很不错的固件
支持楼主 准备开刷！
我120ＷＧ，刷了怎么没有高级选项菜单？？
能不能搞个设置教程，刷上了却不会设置了．．．．
2650bu和rg100a-aa成功刷机。
很好的固件，废话没有，只能说强烈支持Lz
刚刚掉线两次，第一次不能自动重拨。第二次在我记录日志时居然自己拨上号了。。。以下是第二次的日志
login as: admin
admin@192.168.1.1's password:
BusyBox v1.00 (2011.01.14-08:40+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
~ # dmesg
protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 3, 32768 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 18, io mem 0xfffe1300
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6358A1 ATM Network Device v0.1 Jan 14 2011 12:30:56
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Constructed Broadcom Packet Flow Cache v0.1 Feb 26 2009 14:21:08
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1F:A3:42:D4:6F
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
Config Ethernet Switch Through MDIO Pseudo PHY Interface
ethsw: found bcm5325e!
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1F:A3:42:D4:70
KLOB extended to 5 pools
Broadcom BCM6358A1 USB Network Device v0.4 Aug 17 2010 15:57:46
usb0: MAC Address: 00 1F A3 42 D4 71
usb0: Host MAC Address: 00 1F A3 42 D4 72
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: MAC addr from system pool. id:0x776c0000
wl0: MAC Address: 00:1F:A3:42:D4:73
wl0: Broadcom BCM4318 802.11 Wireless Controller 5.10.85.0.cpe4.402.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
proc file create OK for wireless lan.
eth1 Link UP.
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
device usb0 entered promiscuous mode
br0: port 3(usb0) entering learning state
br0: topology change detected, propagating
br0: port 3(usb0) entering forwarding state
I am open &async_queue = 0xc00367c0<3>kill_fasync: bad magic number in fasync_struct!
gpio_fasync
Pasync_queue->magic = 0x4601
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
BcmAdsl_Initialize=0xC0074608, g_pFnNotifyCallback=0xC0094414
KLOB extended to 6 pools
pSdramPHY=0xA7FFFFF8, 0x1B776E 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset:AdslOemDataAddr = 0xA7FF3FD4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
KLOB extended to 7 pools
KLOB extended to 8 pools
bcmxtmrt: MAC address: 00 1f a3 42 d4 74
ip_tables: (C) 2000-2006 Netfilter Core Team
Line 0: xDSL G.994 training
device wl0 left promiscuous mode
br0: port 4(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
br0: port 4(wl0) entering disabled state
Saving OEM data from 0xA7FF3FD4
pSdramPHY=0xA7FFFFF8, 0x1B776E 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset:AdslOemDataAddr = 0xA7FF3FD4
Line 0: ADSL link down
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 4(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL link up, Path 0, us=390, ds=1343
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1021 buckets, 8168 max)
Intrusion -> IN=ppp0 OUT= MAC= SRC=124.237.121.93 DST=116.252.209.65 LEN=40 TOS=0x00 PREC=0x00 TTL=111 ID=256 PROTO=TCP SPT=6000 DPT=9415 WINDOW=16384 RES=0x00 SYN URGP=0
Intrusion -> IN=ppp0 OUT= MAC= SRC=210.14.88.69 DST=116.252.209.65 LEN=44 TOS=0x00 PREC=0x00 TTL=54 ID=60977 DF PROTO=TCP SPT=43346 DPT=14154 WINDOW=8192 RES=0x00 SYN URGP=0
Intrusion -> IN=ppp0 OUT= MAC= SRC=221.7.206.242 DST=116.252.209.65 LEN=40 TOS=0x00 PREC=0x00 TTL=109 ID=57744 PROTO=TCP SPT=6000 DPT=1433 WINDOW=16384 RES=0x00 SYN URGP=0
Intrusion -> IN=ppp0 OUT= MAC= SRC=210.14.88.69 DST=116.252.209.65 LEN=44 TOS=0x00 PREC=0x00 TTL=54 ID=60977 DF PROTO=TCP SPT=43346 DPT=14154 WINDOW=8192 RES=0x00 SYN URGP=0
Intrusion -> IN=ppp0 OUT= MAC= SRC=210.14.88.69 DST=116.252.209.65 LEN=44 TOS=0x00 PREC=0x00 TTL=54 ID=62764 DF PROTO=TCP SPT=44918 DPT=14154 WINDOW=8192 RES=0x00 SYN URGP=0
Line 0: ADSL link down
Saving OEM data from 0xA7FF3FD4
pSdramPHY=0xA7FFFFF8, 0x1B776E 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset:AdslOemDataAddr = 0xA7FF3FD4
Line 0: xDSL G.994 training
Saving OEM data from 0xA7FF3FD4
pSdramPHY=0xA7FFFFF8, 0x1B776E 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset:AdslOemDataAddr = 0xA7FF3FD4
Line 0: ADSL link down
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL link up, Path 0, us=387, ds=1343
~ #
用了一周了，感觉不错，等汉化(bixue:
回复 心何如 的帖子
telnet进路由器，cd到目录，用rm带 -rf 参数删除，股沟一下。
cya001 发表于 2011-1-31 04:21 static/image/common/back.gif
中文固件什么时候发布？给个预告吧
楼主辛苦了！！！