|
|
发表于 2013-10-5 17:51:05
|安徽|
显示全部楼层
本帖最后由 1550261790 于 2013-10-5 21:07 编辑 # |' g9 l, {' A0 R( P. x2 j
; j/ q( \! [) B5 Y电信版烽火HG110刷了，没有CPU ID为tan的选项，选0和1启动不了，选2345则连不上
8 C9 X& t+ e* i: f# [
5 A1 s1 f+ I7 [% I: i. R找到原因了，原来要先刷成D-Link DSL_2640NRU的CFE后，刷这个固件才能正常启动，不用改成tan这个CPU id也能启动。这个固件就是没有USB和SSID只能设置一个，实在有点遗憾。我从dlink官方ftp下载了最新的DSL_2640NRU_v1.0.24_cfe_fs_kernel，TTL下改了Voice Board Configuration的数值后才启动起来的。: @* x1 W# `3 F! N u0 T- o( H; C
Board IP address : 192.168.1.1:ffffff00
+ X3 M) A$ {! _& h% i4 J5 w- j. vHost IP address : 192.168.1.100
9 F2 a. l9 h; M5 k% n; o+ iGateway IP address : 5 s9 V9 B3 o& C$ ~0 [
Run from flash/host (f/h) : f
: ^1 }. [7 q5 uDefault host run file name : vmlinux 3 i- S7 H2 ?: b" A2 s& x# ]. D
Default host flash file name : bcm963xx_fs_kernel " K) K! L. w& r6 x! h
Boot delay (0-9 seconds) : 1
% \$ C! l8 `' ^$ t0 L ^1 LBoot image (0=latest, 1=previous) : 0
) Q7 V5 s* ^+ JBoard Id (0-6) : 96328avng 5 p; M* L% m2 U. c. r
Number of MAC Addresses (1-32) : 11 ) L/ E) W3 i+ l6 E
Base MAC Address : 00:0a:c2:34:55:d8 y8 \4 A' R! `6 S2 D* a
PSI Size (1-64) KBytes : 48 1 e) }3 `# S7 g0 D
Enable Backup PSI [0|1] : 1
, |7 b' l" K" m! s* J |; Y, z. y( cSystem Log Size (0-256) KBytes : 64
1 @* {- r0 Y1 p. lMain Thread Number [0|1] : 0 : A7 _1 b" C3 A
Voice Board Configuration (0-11) : AVNG_VE890HV
. t2 e ]5 v$ R" X' @4 g3 `# j3 N9 r, ?% H8 E
话说刷openwrt-96328avng-16M-flash-generic-squashfs-cfe.bin，硬是没启动起来，也许是跟CFE有关，也许是固件的问题! G: \! O( q* Q( f4 w+ a+ [9 S; i+ }
Booting from only image (0xb8010000) ...* |" L) y4 N* u6 O8 K p* x% A* [
Code Address: 0x80010000, Entry Address: 0x800100000 B% ^1 o& L, ~: C/ V6 Q/ n. | Z$ _
LZMA: Prossible old LZMA format, trying to decompress..: W! C. w: V" u2 S
Decompression OK!
( n0 W( A Y# A, B# g9 b: XEntry at 0x80010000
- {, _/ v7 `1 tClosing network.4 M8 P4 r$ o8 s8 U0 ~% O
Disabling Switch ports.
/ Q5 N" z, W/ I2 J0 b7 |Flushing Receive Buffers...+ y; C6 O* H( g5 y: M% Z5 {+ S/ g9 u
0 buffers found.3 R- o1 ]4 x: ^
Closing DMA Channels.
2 J' @, Y; Q/ I+ ~, YStarting program at 0x80010000
/ [5 E6 i, }6 T( f; \+ p[ 0.000000] Linux version 3.10.13 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38297) ) #1 Thu Oct 3 09:38:26 PDT 2013
' Z5 R1 n; {, V1 \; c, ~: \[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
8 W' m; E9 G$ e% {" q; A[ 0.000000] CPU frequency is 320 MHz
' F; T; i% K- d1 P[ 0.000000] 64MB of RAM installed
" |3 F- L0 h# f" g5 Q, f[ 0.000000] registering 32 GPIOs; L" }4 x% X7 A! t4 @# I: a
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
( l, w5 W8 g) A[ 0.000000] board_bcm963xx: CFE version: unknown
5 ?& ?$ }9 S, P, A- A[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected ffffffff, got d6d2390d)& k# {, m2 n2 A q' u0 Q
[ 0.000000] board_bcm963xx: unknown bcm963xx board: 63av [ 0.000000] bootconsole [early0] enabled
2 {- ~/ {5 ?# }1 @[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)
6 E+ j1 Y( t0 O[ 0.000000] Kernel panic - not syncing: unable to detect bcm963xx board
2 V/ o& U) Z$ N |
|
楼主: zhjook
/1 
44152102000001
