|
|
如题,下午在以色列论坛下载了2760U-E1的新版固件1.25(201210月)和1.27 (20134月的版本 ) ,两个版本的主登录IP都是锁定10.0.0.138,不能像ps3版本那样改成192.168.1.1 ,改动的时候提示这个ip已经被其他net gruop 占用了,在cfg 里边找了半天没有找到,谁知道,如果解锁这个,附件是1.25的cfg ,1.27的cfg 是二进制文件,不是xml
Device Info
| Model Name: | DSL-2760U/E1 | | Board ID: | 96328avng | | Software Version: | BN_1.25-CCOD_OpenWifi | | Bootloader (CFE) Version: | 1.0.37-106.24 | | Release Date: | Oct. 22, 2012 |
This information reflects the current status of your WAN connection.
[tr][/tr]
| Line Rate - Upstream (Kbps): | 638 | | Line Rate - Downstream (Kbps): | 3779 | | LAN IPv4 Address: | 10.0.0.138 | | Default Gateway: | ppp0 | | Primary DNS Server: | 202.106.195.68 | | Secondary DNS Server: | 202.106.46.151 | | Date/Time: | Mon May 13 17:30:25 2013 |
CFE version 1.0.37-106.24 for BCM96328 (32bit,SP,BE)
Build Date: ?????? ?????? 21 08:38:40 UTC 2012 (legath@desk)
Copyright (C) 2000-2009 Broadcom Corporation.
HS Serial flash device: name S25FL128, id 0x0118 size 16384KB
Total Flash size: 16384K with 256 sectors
Chip ID: BCM6328B0, MIPS: 320MHz, DDR: 320MHz, Bus: 160MHz
Main Thread: TP0
Memory Test Passed
Total Memory: 67108864 bytes (64MB)
Boot Address: 0xb8000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-6) : 96328avng
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:0a:c2:c3:fa:a7
PSI Size (1-64) KBytes : 48
Enable Backup PSI [0|1] : 1
System Log Size (0-256) KBytes : 48
Main Thread Number [0|1] : 0
Voice Board Configuration (0-11) : AVNG_VE890HVP
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 110
Booting from latest image (0xb8010000) ...
Code Address: 0x80010000, Entry Address: 0x80014230
Decompression OK!
Entry at 0x80014230
Closing network.
Disabling Switch ports.
Flushing Receive Buffers...
30 buffers found.
Closing DMA Channels.
Starting program at 0x80014230
Linux version 2.6.30 (joan@localhost.localdomain) (gcc version 4.4.2 (Buildroot 2010.02-git) ) #1 Mon Oct 22 09:42:49 CST 2012
HS Serial flash device: name S25FL128P, id 0x0118 size 16384KB
96328avng prom init
CPU revision is: 0002a075 (Broadcom4350)
Determined physical RAM map:
memory: 03f00000 @ 00000000 (usable)
Zone PFN ranges:
DMA 0x00000000 -> 0x00001000
Normal 0x00001000 -> 0x00003f00
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
0: 0x00000000 -> 0x00003f00
On node 0 totalpages: 16128
free_area_init_node: node 0, pgdat 80366490, node_mem_map 81000000
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 94 pages used for memmap
Normal zone: 11938 pages, LIFO batch:1
Built 1 zonelists in Zone order, mobility grouping on. Total pages: 16002
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
wait instruction: enabled
Primary instruction cache 32kB, VIPT, 4-way, linesize 16 bytes.
Primary data cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes
RCU-based detection of stalled CPUs is enabled.
NR_IRQS:128
PID hash table entries: 256 (order: 8, 1024 bytes)
console [ttyS0] enabled
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 60152k/64512k available (2754k kernel code, 4340k reserved, 667k data, 124k init, 0k highmem)
Calibrating delay loop... 319.48 BogoMIPS (lpj=159744)
Mount-cache hash table entries: 512
net_namespace: 812 bytes
NET: Registered protocol family 16
Total Flash size: 16384K with 256 sectors
registering PCI controller with io_map_base unset
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
pci 0000:00:09.0: reg 10 32bit mmio: [0x10002600-0x100026ff]
pci 0000:00:0a.0: reg 10 32bit mmio: [0x10002500-0x100025ff]
pci 0000:01:00.0: PME# supported from D0 D3hot
pci 0000:01:00.0: PME# disabled
pci 0000:02:00.0: reg 10 64bit mmio: [0x000000-0x003fff]
pci 0000:02:00.0: supports D1 D2
pci 0000:01:00.0: PCI bridge, secondary bus 0000:02
pci 0000:01:00.0: IO window: disabled
pci 0000:01:00.0: MEM window: 0x10f00000-0x10ffffff
pci 0000:01:00.0: PREFETCH window: disabled
PCI: Enabling device 0000:01:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:01:00.0 to 64
BLOG v2.1 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 2048 (order: 2, 16384 bytes)
TCP bind hash table entries: 2048 (order: 1, 8192 bytes)
TCP: Hash tables configured (established 2048 bind 2048)
TCP reno registered
NET: Registered protocol family 1
squashfs: version 4.0 (2009/01/31) Phillip Lougher
squashfs: version 4.0 with LZMA457 ported by BRCM
NTFS driver 2.1.29 [Flags: R/W].
fuse init (API version 7.11)
msgmni has been set to 117
io scheduler noop registered (default)
pcieport-driver 0000:01:00.0: device [14e4:6328] has invalid IRQ; check vendor BIOS
PCI: Setting latency timer of device 0000:01:00.0 to 64
Driver 'sd' needs updating - please use bus_type methods
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
File system address: 0xb8010100
ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: Enabling legacy PCI PM
ehci_hcd 0000:00:0a.0: irq 50, io mem 0x10002500
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 49, io mem 0x10002600
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 1 port detected
usbcore: registered new interface driver usblp
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
SES: LED GPIO 0x8009 is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xb0000100 (irq = 36) is a BCM63XX
ttyS1 at MMIO 0xb0000120 (irq = 36) is a BCM63XX
bcmxtmrt: Broadcom BCM6328B0 ATM/PTM Network Device v0.3 Oct 22 2012 09:39:00
Broadcom Logger v0.1 Oct 22 2012 09:38:22
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 17
NET: Registered protocol family 15
Initializing MCPD Module
Ebtables v2.0 registered
ebt_time registered
ebt_ftos registered
ebt_wmm_mark registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly on device 31:0.
Freeing unused kernel memory: 124k freed
init started: BusyBox v1.00 (2012.10.22-01:45+0000) multi-call binary
usbfs: unrecognised mount option "0" or missing value
usbfs: mount parameter error.
BusyBox v1.00 (2012.10.22-01:45+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
Disabling lock debugging due to kernel taint
Broadcom Packet Flow Cache Char Driver v2.1 Mar 18 2010 21:39:51 Registered<242>
NBUFF v1.0 Initialized
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Broadcom Packet Flow Cache registered with netdev chain
Constructed Broadcom Packet Flow Cache v2.1 Mar 18 2010 21:39:50
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6328B0 Ethernet Network Device v0.1 Oct 22 2012 09:38:35
dgasp: kerSysRegisterDyingGaspHandler: bcmsw registered
eth0: MAC Address: 00:0A:C2:C3:FA:A7
eth1: MAC Address: 00:0A:C2:C3:FA:A7
eth2: MAC Address: 00:0A:C2:C3:FA:A7
eth3: MAC Address: 00:0A:C2:C3:FA:A7
eth4: MAC Address: 00:0A:C2:C3:FA:A7
LAN4 Link UP 100 mbps full duplex
LAN0 Link UP 1000 mbps full duplex
message received before monitor task is initialized kerSysSendtoMonitorTask
BCM63XX_USB USB Device not present
insmod: cannot insert `/lib/modules/2.6.30/extra/bcm_usb.ko': Success (19): Success
PCI: Enabling device 0000:02:00.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:02:00.0 to 64
wl:srom not detected,using main memory mapped srom info(wombo board)
wl:loading /etc/wlan/bcm4313_map.bin
wl0: Broadcom BCM4313 802.11 Wireless Controller 5.60.120.3.cpe4.406.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
Broadcom 802.1Q VLAN Interface, v0.1
===== Release Version 4.06L.01 (build timestamp 121022_0943) =====
ifconfig: br0: error fetching interface information: Device not found
ifconfig: br0: error fetching interface information: Device not found
ip_tables: (C) 2000-2006 Netfilter Core Team
ifconfig: br0: error fetching interface information: Device not found
status = enable netBiosName=bezeq directoryName =bezeq utf8DirName=bezeq charset=utf8
br0IP=10.0.0.138 br0Mask=10.0.0.0
killall: imspector: no process killed
hotspotCfg->externalCaptivePortal=[pwcaptive.bezeq.co.il], hotspotCfg->sessionExpirationTime=[1800], hotspotCfg->accessLimitation=[5]
device eth0 entered promiscuous mode
br0: port 1(eth0) entering forwarding state
tr69c:error:16.865:initLoggingFromConfig:276:failed to get lock, ret=9809
Scratch pad is not initialized.
Scratch pad is not initialized.
device eth1 entered promiscuous mode
device eth2 entered promiscuous mode
device eth3 entered promiscuous mode
device wl0 entered promiscuous mode
WLmngr Daemon is running
optarg=0 shmId=0
br0: port 5(wl0) entering forwarding state
wlevt_init@107: opened loopback socket 4
wlevt is ready for new msg...
smbd deleted
.nmbd deleted
.status = enable netBiosName=bezeq directoryName =bezeq utf8DirName=bezeq charset=utf8
br0IP=10.0.0.138 br0Mask=10.0.0.0
I am open &async_queue = 0xc06d853c<3>kill_fasync: bad magic number in fasync_struct!
my_timeout:Pasync_queue->magic = 0x0
wlButtonInit open gpio_fasync
success
Pasync_queue->magic = 0x4601
tr69c:error:23.039:updateTr69cCfgInfo:519:Could not get lock, ret=9809
wlmngr_initCfg:dataSync:1
hotspotCfg->externalCaptivePortal=[pwcaptive.bezeq.co.il], hotspotCfg->sessionExpirationTime=[1800], hotspotCfg->accessLimitation=[5]
BcmAdsl_Initialize=0xC00E2FEC, g_pFnNotifyCallback=0xC0106A94
pSdramPHY=0xA3FFFFF8, 0x1B7782 0xDEADBEEF
*** PhySdramSize got adjusted: 0x76268 => 0x8BFB0 ***
AdslCoreSharedMemInit: shareMemAvailable=475184
AdslCoreHwReset: AdslOemDataAddr = 0xA3F6C9A4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
Scratch pad is not initialized.
No scratch pad found. Initialize scratch pad...
iptables v1.4.0: can't initialize iptables table `nat': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
iptables v1.4.0: can't initialize iptables table `nat': Table does not exist (do you need to insmod?)
Perhaps iptables or your kernel needs to be upgraded.
Line 0: xDSL G.994 training
message received before monitor task is initialized kerSysSendtoMonitorTask
Cannot find device "atm0"
Action 4 device ifb0 ifindex 2
tr69c:error:29.040:setDefaultActiveNotification:3290:could not get lock
Cannot find device "atm0"
Action 4 device ifb0 ifindex 2
monitor task is initialized pid= 249
tr143EchoCfgServer:notice:31.348:main:322:calling cmsMdm_init with shmId=0
tr143EchoCfgServer:notice:31.348:cmsMdm_init:175:entered, eid=103(tr143EchoCfgServer) shmid=0
tr143EchoCfgServer:notice:31.348:oalShm_init:135:attaching to existing shmId=0
tr143EchoCfgServer:notice:31.349:oalLck_init:114:attach existing done, semid=0
tr143EchoCfgServer:notice:31.349:cmsMem_initSharedMemPointer:133:shm pool: 0x58811e04-0x58888000
tr143EchoCfgServer:error:31.350:main:332:setupConfig error ret=-1
tr143EchoCfgServer:notice:31.350:cmsMdm_cleanup:351:entered
tr143EchoCfgServer:notice:31.351:cmsMdm_cleanup:359:done
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (1008 buckets, 4032 max)
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
wl0.1 (): not using net_device_ops yet
wl0.2 (): not using net_device_ops yet
wl0.3 (): not using net_device_ops yet
br0: port 5(wl0) entering disabled state
Setting SSID: "Bezeq-N_c3faa7"
Setting SSID: "Bezeq Free C3FAA7"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b06
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
ssk:error:34.385:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:34.385:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
ssk:error:36.474:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:36.474:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:36.626:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:36.626:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:36.691:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
ssk:error:36.691:lck_checkBeforeEntry:171:lock required during cmsObj_getNextInSubTreeFlags
Cannot find device "atm0"
Action 4 device ifb0 ifindex 2
Line 0: ADSL G.992 started
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
Line 0: ADSL G.992 channel analysis
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
br0: port 5(wl0) entering disabled state
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlmngr_init:dataSync:1
wlmngr_initCfg:dataSync:1
Setting SSID: "Bezeq-N_c3faa7"
Setting SSID: "Bezeq Free C3FAA7"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b06
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Cannot find device "atm0"
Action 4 device ifb0 ifindex 2
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does Line 0: ADSL G.992 message exchange
not exist.
Line 0: ADSL link down
bcmxtmcfg: XTM Link Information, portid = 0, State = DOWN, Service Support = ATM
Line 0: xDSL G.994 training
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL G.992 message exchange
Line 0: ADSL link up, Path 0, us=638, ds=3779
bcmxtmcfg: XTM Link Information, portid = 0, State = UP, Service Support = ATM
(ssk) xDSL link up, Connection Type: ATM
bcmxtmrt: MAC address: 00 0a c2 c3 fa a9
[DoCreateDeviceReq.2288]: register_netdev
[DoCreateDeviceReq.2290]: register_netdev done
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=3779000
bcmxtmrt: MAC address: 00 0a c2 c3 fa aa
[DoCreateDeviceReq.2288]: register_netdev
[DoCreateDeviceReq.2290]: register_netdev done
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=3779000
PPP: ppp1 Start to connect ...
PPP: ppp1 Start to connect ...
PPP: ppp1 Start to connect ...
PPP: ppp1 Start to connect ...
PPP: ppp1 Start to connect ...
bcmxtmcfg: OAM loopback response not received on VCC 1.8.3
bcmxtmcfg: OAM loopback response not received on VCC 1.8.48
bcmxtmcfg: OAM loopback response not received on VCC 1.8.4
bcmxtmcfg: OAM loopback response not received on VCC 1.8.48
PPP: ppp1 Start to connect ...
PPP: ppp1 Start to connect ...
smd:error:248.439:collectApp:1167:Could not collect pppd (pid=2271 timeout=5000ms), ret=9809. Kill it with SIGKILL.
Primary DNS server = 0.0.0.0
Secondary DNS server = 0.0.0.0
iptables: Bad rule (does a matching rule exist in that chain?)
dnsprobe:Network Has Some Error....Change To Hajack Mode
iptables: Bad rule (does a matching rule exist in that chain?)
httpd:error:253.259:rutPMap_deleteFilter:767:could not find InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.2
httpd:error:253.260:rutPMap_deleteAvailableInterface:955:Could not find avail InterfaceReference InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.2
httpd:error:253.260:mdm_deleteObjectInstance:1221:wrong instance depth, iidStack(0) objNode(1)
httpd:error:253.260:rutPMap_deleteAvailableInterface:964:could not delete available interface, ret=9005
httpd:error:255.717:rutPMap_deleteFilter:767:could not find InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.3
httpd:error:255.718:rutPMap_deleteAvailableInterface:955:Could not find avail InterfaceReference InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.3
httpd:error:255.718:mdm_deleteObjectInstance:1221:wrong instance depth, iidStack(0) objNode(1)
httpd:error:255.718:rutPMap_deleteAvailableInterface:964:could not delete available interface, ret=9005
Primary DNS server = 0.0.0.0
Secondary DNS server = 0.0.0.0
dnsprobe:Network Has Some Error....Change To Hajack Mode
iptables: Bad rule (does a matching rule exist in that chain?)
httpd:error:258.390:rutPMap_deleteFilter:767:could not find InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.4
httpd:error:258.391:rutPMap_deleteAvailableInterface:955:Could not find avail InterfaceReference InternetGatewayDevice.WANDevice.1.WANConnectionDevice.1.WANPPPConnection.4
httpd:error:258.392:mdm_deleteObjectInstance:1221:wrong instance depth, iidStack(0) objNode(1)
httpd:error:258.392:rutPMap_deleteAvailableInterface:964:could not delete available interface, ret=9005
Primary DNS server = 0.0.0.0
Secondary DNS server = 0.0.0.0
dnsprobe:Network Has Some Error....Change To Hajack Mode
iptables: Bad rule (does a matching rule exist in that chain?)
ssk:error:261.807:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.808:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.808:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.809:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.809:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.809:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.810:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.810:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
ssk:error:261.811:processWatchWanConnectionMsg:1038:could not get wanConn object to do update on, ret=9005
bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
bcmxtmcfg: Connection DOWN, LinkActiveStatus=0x0
bcmxtmrt: MAC address: 00 0a c2 c3 fa a9
[DoCreateDeviceReq.2288]: register_netdev
[DoCreateDeviceReq.2290]: register_netdev done
bcmxtmcfg: Connection UP, LinkActiveStatus=0x1, US=638000, DS=3779000
dnsprobe:Network Has Some Error....Change To Hajack Mode
dnsprobe:Network Has Some Error....Change To Hajack Mode
Primary DNS server = 0.0.0.0
Secondary DNS server = 0.0.0.0
dnsprobe:Network Has Some Error....Change To Hajack Mode
iptables: Bad rule (does a matching rule exist in that chain?)
PPP: ppp0 Start to connect ...
saving ppp session info ppp0(4c1fcc477de3/1981)
PPP: ppp0 Connection Up.
ssk:error:331.986:rut_fakeDnsForwarding:857:rut_fakeDnsForwarding---->128.9.0.107
iptables: Bad rule (does a matching rule exist in that chain?)
Primary DNS server = 202.106.195.68
Secondary DNS server = 202.106.46.151
iptables: Resource temporarily unavailable
All services associated with ppp0 is activated.
iptables: Bad rule (does a matching rule exist in that chain?)
Intrusion -> IN=ppp0 OUT= MAC= SRC=112.101.64.27 DST=123.119.28.68 LEN=40 TOS=0x00 PREC=0x00 TTL=117 ID=256 PROTO=TCP SPT=30746 DPT=6673 WINDOW=16384 RES=0x00 SYN URGP=0 MARK=0x8000000
Intrusion -> IN=ppp0 OUT= MAC= SRC=182.236.163.115 DST=123.119.28.68 LEN=40 TOS=0x00 PREC=0x00 TTL=247 ID=33802 DF PROTO=TCP SPT=43766 DPT=6675 WINDOW=512 RES=0x00 SYN URGP=0 MARK=0x8000000
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
br0: port 5(wl0) entering disabled state
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlmngr_init:dataSync:1
wlmngr_initCfg:dataSync:1
Setting SSID: "DSL-2760U"
Setting SSID: "Bezeq Free C3FAA7"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b06
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
Sorry, rule does not exist.
Sorry, rule does not exist.
Sorry, rule does not exist.
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
br0: port 5(wl0) entering disabled state
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlmngr_init:dataSync:1
wlmngr_initCfg:dataSync:1
Setting SSID: "DSL-2760U"
Setting SSID: "Bezeq Free C3FAA7"
Setting SSID: "wl0_Guest2"
Setting SSID: "wl0_Guest3"
Chanspec set to 0x2b06
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 entered promiscuous mode
br0: port 5(wl0) entering forwarding state
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看，没有账号？注册
×
|
|Archiver|小黑屋|宽带技术网
|网站地图
发表于 2013-5-13 22:24:53
