|
|
cfe信息如下：
CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE)
Build Date: Wed Mar 31 16:51:00 CST 2010 (richard@SWD100)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h)
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Check Reset Default Hold [0|1] : 0
Board Id (0-12) : 96358VW2_N60
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:25:5e:cf:c2:7d
PSI Size (1-64) KBytes : 48
Main Thread Number [0|1] : 0
User Password : "wcvdz"
WLAN SSID Paramters : "China
Device Serial Number : "4220000255ECFC27D"
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe5e0000) ...
Read flash at blk[47]
Code Address: 0x80010000, Entry Address: 0x80319000
Decompression OK!
Entry at 0x80319000
Closing network.
Closing DMA Channels.
Starting program at 0x80319000
Linux version 2.6.21.5 (chenxi@localhost.localdomain) (gcc version 4.2.3) #58 Sa
t Aug 7 06:39:18 CST 2010
Parallel flash device: name AM29LV320MT, id 0x220
96358VW2_N60 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 31 pages used for memmap
Normal zone: 3969 pages, LIFO batch:0
Built 1 zonelists. Total pages: 8033
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged,
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28696k/32384k available (2272k kernel code, 3688k reserved, 832k data, 9
6k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 299.00 BogoMIPS (lpj=747520)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe5e0100
before hw_init(). dir-high:0, dir:8c000bf, io-high:3f, io:ff7ff3db, mode:0
MPI: Detected 5 vdc 16-bit PCMCIA card
after hw_init(). dir-high:3, dir:8c000bf, io-high:3f, io:ff7ff3db, mode:880
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BLOG v1.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
NET: Registered protocol family 2
Time: MIPS clocksource has been installed.
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/O].
JFFS2 version 2.2. (C) 2001-2006 Red Hat, Inc.
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0x8030b4f4,4194304]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 18, io mem 0xfffe1300
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
hub 1-0:1.0: over-current change on port 2
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x801b is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6358A1 ATM Network Device v0.1 Apr 14 2010 03:25:19
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
TCP cubic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
KLOB extended to 2 pools
init started: BusyBox v1.00 (2010.04.13-19:28+0000) multi-call binary
BusyBox v1.00 (2010.04.13-19:28+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
pktflow: module license 'Proprietary' taints kernel.
blog_fc_flsuh_fn<c00668f0> blog_fc_status_fn<c00661f8> blog_fc_bind_blog_fn<c006
6514>
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Constructed Broadcom Packet Flow Cache v0.1 Feb 26
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
before enet_probe(). dir-high:3, dir:8c000ff, io-high:3f, io:ff7ff3db, mode:880
KLOB extended to 3 pools
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 14 2010 03:25:13
KLOB extended to 4 pools
KLOB extended to 5 pools
KLOB extended to 6 pools
Config Ethernet Switch Through MDIO Pseudo PHY Interface
ethsw: found bcm5325e!
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:25:5E:CF:C2:7D
after enet_probe(). dir-high:3, dir:8c000ff, io-high:3f, io:ff7ff3db, mode:40000
880
Broadcom BCM6358A1 USB Network Device v0.4 Apr 14 2010 03:25:14
usb0: MAC Address: 00 25 5E CF C2 7E
usb0: Host MAC Address: 00 25 5E CF C2 7F
eth0 Link UP.
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: srom not detected, using main memory mapped srom info (wombo board)
KLOB extended to 7 pools
wl0: wlc_attach: MAC addr from system pool. id:0x776c0000
wl0: MAC Address: 00:25:5E:CF:C2:80
wl0: Broadcom BCMa8d6 802.11 Wireless Controller 5.10.85.0.cpe4.402.0
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
===== Release Version 4.02L.02 (build timestamp 100807_0639) =====
wl_cnt= 1
nvramRestore=0
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
/bin/cvtpsi -r
read log from flash (uncompress: 3784 bytes, compress: 0 bytes)
eth0.2: MAC Address: 00:25:5E:CF:C2:7D
eth0.3: MAC Address: 00:25:5E:CF:C2:7D
eth0.4: MAC Address: 00:25:5E:CF:C2:7D
eth0.5: MAC Address: 00:25:5E:CF:C2:7D
udhcp server (v0.9.6) started. pid[216], ppid[158]
device eth0.2 is not a slave of br0
device eth0.2 entered promiscuous mode
br0: port 1(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0.2) entering forwarding state
rut_lan.c,659
device eth0.3 is not a slave of br0
device eth0.3 entered promiscuous mode
br0: port 2(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.3) entering forwarding state
rut_lan.c,659
device eth0.4 is not a slave of br0
device eth0.4 entered promiscuous mode
br0: port 3(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.4) entering forwarding state
rut_lan.c,659
device eth0.5 is not a slave of br0
device eth0.5 entered promiscuous mode
br0: port 4(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.5) entering forwarding state
rut_lan.c,659
WLmngr Daemon i
optarg=0 shmId=0
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 5(wl0) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0) entering forwarding state
udhcp handle msg...
DHCP server enable, backup server disable, msg src[1]
rut_lan.c,659
BcmAdsl_Initialize=0xC00C65F8, g_pFnNotifyCallback=0xC00ECE54
KLOB extended to 8 pools
pSdramPHY=0xA1FFFFF8, 0xFFFBFFFF 0xFFFFBFFF
AdslCoreSharedMemInit: shareMemAvailable=21712
AdslCoreHwReset: AdslOemDataAddr = 0xA1
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
bcmxtmrt: MAC address: 00 25 5e cf c2 81
brctl cmd -i 0:0
atm0 -- ppp0
brctl enableproxymode br0 1 > /dev/null
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
wlctl -i wl0 phytype > /var/wl0
wlctl -i wl0 revinfo > /var/wl0
wlctl -i wl0 bands > /var/wl0bands
wlctl ver > /var/wlver
wlctl -i wl0 cap > /var/wl0cap
killall bftpd
killall: bftpd: no process killed
ssk:error:17.629:ssk_main:1291:cannot handle msg type 0x1000026b
getsockopt failed strangely: Protocol not available
getsockopt failed strangely: Protocol not available
clear all wirless snooping group!
br0: port 5(wl0) entering disabled state
FUNC = wlmngr_ReadCfeDevPin, Line = 2664
InValid Device Pin in CFE
WPS Device PIN = 16696938
wlctl -i wl0 phy_watchdog 0
wlctl -i wl0 wds none
wlctl -i wl0 up
wlctl -i wl0 down
wlctl -i wl0 mbss 1
wlctl -i wl0 bss -C 0 down
wlctl -i wl0 bss -C 1 down
wlctl -i wl0 bss -C 2 down
wlctl -i wl0 bss -C 3 down
wlctl -i wl0 ssid -C 0 'C''h''i''n''a''N''e''t''-''r''s''D''a'
Setting SSID "ChinaNet-rsDa"
wlctl -i wl0 ssid -C 1 'C''h''i''n''a''N''e''t''-''D''B''2'
Setting SSID "ChinaNet-DB2"
wlctl -i wl0 ssid -C 2 'C''h''i''n''a''N''e''t''-''D''B''3'
Setting SSID "ChinaNet-DB3"
wlctl -i wl0 ssid -C 3 'C''h''i''n''a''N
Setting SSID "ChinaNet-DB4"
wlctl -i wl0 cur_etheraddr 00:25:5E:CF:C2:80 2>/dev/null
wlctl -i wl0.1 cur_etheraddr 52:25:5e:cf:c2:81 2>/dev/null
wlctl -i wl0.2 cur_etheraddr 52:25:5e:cf:c2:82 2>/dev/null
wlctl -i wl0.3 cur_etheraddr 52:25:5e:cf:c2:83 2>/dev/null
wlctl -i wl0 ap 1
wlctl -i wl0 infra 1
wlctl -i wl0 closed 0
wlctl -i wl0 country CN
wlctl -i wl0 band b
wlctl -i wl0 regulatory 0
wlctl -i wl0 radar 0 2>/dev/null
wlctl -i wl0 spect 0 2>/dev/null
wlctl -i wl0 nmode -1
wlctl -i wl0 mimo_bw_cap 2
wlctl -i wl0 wpa_cap -C 0 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 0 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 1 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 1 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 2 > /var/wpa_cap0
wlctl -i wl0 wpa_cap -C 2 0 2>/dev/null
wlctl -i wl0 wpa_cap -C 3 > /var/wpa_cap0
wlctl: Unsupported
br_handle_frame_finish src_ip[192.168.1.2] dest_ip[255.255.255.255] src_port[68]
dest_port[67]
state[3] option 60 Field Type[0x46]
br_pass_frame_up
br_handle_frame_finish src_ip[0.0.0.0] dest_ip[255.255.255.25
t_port[67]
state[1] option 60 Field Type[0x46]
br_pass_frame_up
br_handle_frame_finish src_ip[0.0.0.0] dest_ip[255.255.255.255] src_port[68] des
t_port[67]
state[3] option 60 Field Type[0x46]
br_pass_frame_up
br_handle_frame_finish src_ip[192.168.1.2] dest_ip[255.255.255.255] src_port[68]
dest_port[67]
state[8] option 60 Field Type[0x46]
br_pass_frame_up
br_handle_frame_finish src_ip[192.168.1.2] dest_ip[255.255.255.255] src_port[68]
dest_port[67]
state[8] option 60 Field Type[0x46]
br_pass_frame_up
wlctl -i wl0 wpa_cap -C 3 0 2>/dev/null
wlctl -i wl0 maxassoc 16
wlctl -i wl0 bss_maxassoc 16
wlctl -i wl0 gmode Auto
wlctl -i wl0 gmode_protection_override -1
wlctl -i wl0 gmode_protection_control 2
wlctl -i wl0 nmode_protection_override -1
wlctl -i wl0 protection_control 2
wlctl -i wl0 nreqd 0
wlctl -i wl0 wme 0 2>/dev/null
wlctl -i wl0 afterburner_override 0 2>/dev/null
wlctl -i wl0 ampdu 1
wlctl -i wl0 amsdu 1
wlctl -i wl0 afterburner_override 0
wlctl -i wl0 wme 1 2>/dev/null
wlctl -i wl0 wme_noack 0 2>/dev/nul
wlctl -i wl0 wme_apsd 1 2>/dev/null
wlctl -i wl0 wme_bss_disable 0
wlctl -i wl0 rate 0
wlctl -i wl0 bg_rate 0
wlctl -i wl0 leddc 0 2>/dev/null
wlctl -i wl0 mrate -1
wlctl -i wl0 bg_mrate -1
wlctl -i wl0 rateset default
wlctl -i wl0 rtsthresh 2347
wlctl -i wl0 fragthresh 2346
wlctl -i wl0 dtim 1
wlctl -i wl0 bi 100
wlctl -i wl0 frameburst 0
wlctl -i wl0 ap_isolate 0
wlctl -i wl0 wds none
wlctl -i wl0 pwr_percent 100
wlctl -i wl0 wmf_bss_enable 0
wlctl -i wl0.1 wmf_bss_enable 0
wlctl -i wl0.2 wmf_bss_enable 0
wlctl -i wl0.3 wmf_bss_enable 0
wlctl -i wl0 mac none
wlctl -i wl0 macmode 0
wlctl -i wl0 lazywds 0
wlctl -i wl0 wds
rutQos_setDefaultWlQueuesLock() returns error. ret=9804
wlctl -i wl0 up
wl led 0 32 0
wlctl -i wl0 autochannel 1
wlctl -i wl0 autochannel 2
chanspec 0x2b06 selected
wlctl -i wl0 csscantimer 0
wlctl -i wl0 chanspec > /var/curchaspec0
br0: port 5(wl0) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 5(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 5(wl0) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0) entering forwarding state
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0
wlctl -i wl0 rmwep -C 0 0
wlctl -i wl0 rmwep -C 0 1
wlctl -i wl0 rmwep -C 0 2
wlctl -i wl0 rmwep -C 0 3
wlctl -i wl0 rmwep -C 1 0
wlctl -i wl0 rmwep -C 1 1
wlctl -i wl0 rmwep -C
wlctl -i wl0 rmwep -C 1 3
wlctl -i wl0 rmwep -C 2 0
wlctl -i wl0 rmwep -C 2 1
wlctl -i wl0 rmwep -C 2 2
wlctl -i wl0 rmwep -C 2 3
wlctl -i wl0 rmwep -C 3 0
wlctl -i wl0 rmwep -C 3 1
wlctl -i wl0 rmwep -C 3 2
wlctl -i wl0 rmwep -C 3 3
wlctl -i wl0 wsec -C 0 6
wlctl -i wl0 wsec_restrict -C 0 1
wlctl -i wl0 wpa_auth -C 0 132
wlctl -i wl0 eap 1
wlctl -i wl0 auth -C 0 0
wlctl -i wl0 bss -C 0 up
++++++++++func = wlmngr_wlIfcUp,line = 127,idx = 0
wlmngr_startWsc: client-pbc mode
wlctl -i wl0 phy_watchdog 1
wl led 0 2 1
wlctl -i wl0 chanspec > /var/curchaspec0
wlctl -i wl0 authe_sta_list > /var/wl0_authe
wlctl -i wl0 assoclist > /var/wl0_assoc
wlctl -i wl0 autho_sta_list > /var/wl0_autho
wlctl -i wl0 authe_sta_list > /var/wl0_authe
wlctl -i wl0 assoclist > /var/wl0_assoc
wlctl -i wl0 autho_sta_list > /var/wl0_autho
按reset加电源也失败，忘高手解答
|
|
粤公网安备44152102000001号 
发表于 2012-9-8 21:42:26