EC1308 机顶盒裸照

lawman

上两张EC1308的裸照，没有TTL线啊，怎么办啊？
是不是那六个柱子的就是TTL线的接口啊？这种借口哪里有买的么？

极地枫

居然有uboot，还是128m'内存，内核2.6的，够强劲啊。打个问号看看有没有帮助信息，或者ctrl+C或者esc看看。

zhuanghong

试试TELNET 能不能进去。

jht-007

坏了的话当尸体卖给我吧，20元包邮，呵呵。

lawman

不接那个5V就不烧
从上到下 1：空 2：gnd 3：t 4：r 5:3.3v 6：空
大头针从地板背后插入

从别人那里得到一些信息，赌一把吧，找些大头针接接看了

lawman

TTL 线连上了 EC1308

然后呢？怎么Telnet？我要复位啊！

U-Boot 1.1.4 (Aug 20 2009 - 16:19:34)

U-Boot code: F0500000 -> F051F500  BSS: -> F0588A08
YX_VERSION=U_BOOT_1_1_4-YX5531EB01HIS3560FW049C01 @ 2009-8-20 16:25:40
RAM Configuration:
Bank #0: f0000000 128 MB
YX NAND init information:
ID:9510daad  TYPE:Hynix 8-bit nand_flash  SIZE:256MB
Serial code: 13080942H1B281776
Board  name: YX5531D
MAC address: 00:07:67:24:4c:b0
normal  start
In:    serial
Out:   serial
Err:   serial
Flash MAC->[00:07:67:24:4c:b0]
MAC:   00-07-67-24-4C-B0
X:[40] Y:[471] W:[100] H:[15] COLOR:[0xffffff80]
Hit any key to stop autoboot:  0
bootm in nand !
## Booting image at f0008000 ...
   Image Name:   yslinux
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    1122824 Bytes =  1.1 MB
   Load Address: f0a00000
   Entry Point:  f0a00000
OK

Starting kernel ...

Uncompressing Linux........................................................................ done, booting the kernel.
Linux version 2.6.14-hi3560v100-pilot-test-pa-release (root@localhost) (gcc version 3.4.3 (release) (CodeSourcery ARM Q3cvs 2004)) #3 Wed Jul 22 18:24:28 CST 2009
CPU: ARM926EJ-Sid(wb) [41069265] revision 5 (ARMv5TEJ)
Machine: Hi3560v100
Memory policy: ECC disabled, Data cache writeback
CPU0: D VIVT write-back cache
CPU0: I cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
CPU0: D cache: 16384 bytes, associativity 4, 32 byte lines, 128 sets
Built 1 zonelists
Kernel command line: mem=64M console=ttyAMA0,115200 root=/dev/mtdblock/7 rootfstype=yaffs2 nand_mtdparts=phys_mapped_flash:256K(uboot),384K(nvram),640K(reserve),384K(config0),384K(config1),3M(kernel0),3M(kernel1),40M(root0),40M(root1),-(roothome) kernel=flash0.kernel0 runlevel=4 yxip=10.0.0.255
PID hash table entries: 512 (order: 9, 8192 bytes)
Console: colour dummy device 80x30
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 64MB = 64MB total
Memory: 62464KB available (1847K code, 370K data, 76K init)
Mount-cache hash table entries: 512
HI_VERSION=LINUX_2_6_14-M05C0404B0202 @Hi3560v100_OSDrv_1_0_0_2 2008-08-14 18:53:45
CPU: Testing write buffer coherency: ok
NET: Registered protocol family 16
Hisilicon clock system V0.01
SCSI subsystem initialized
NetWinder Floating Point Emulator V0.97 (double precision)
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
yaffs Jul 22 2009 18:22:30 Installing.
Initializing Cryptographic API
Serial: AMBA PL011 UART driver
ttyAMA0 at MMIO 0x101f1000 (irq = 12) is a AMBA/PL011
ttyAMA1 at MMIO 0x101f2000 (irq = 13) is a AMBA/PL011
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered
loop: loaded (max 8 devices)
nbd: registered device at major 43
PPP generic driver version 2.4.2
NET: Registered protocol family 24
HISI_NAND-MDC040003B040002 @Hi3560v100_OSDrv_1_0_0_2 2008-12-18 17:21:50
NAND device: Manufacturer ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
here1!
Creating 10 MTD partitions on "NAND 256MiB 3,3V 8-bit":
0x00000000-0x00040000 : "uboot"
0x00040000-0x000a0000 : "nvram"
0x000a0000-0x00140000 : "reserve"
0x00140000-0x001a0000 : "config0"
0x001a0000-0x00200000 : "config1"
0x00200000-0x00500000 : "kernel0"
0x00500000-0x00800000 : "kernel1"
0x00800000-0x03000000 : "root0"
0x03000000-0x05800000 : "root1"
0x05800000-0x10000000 : "roothome"
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 4096 (order: 2, 16384 bytes)
TCP bind hash table entries: 4096 (order: 2, 16384 bytes)
TCP: Hash tables configured (established 4096 bind 4096)
TCP reno registered
TCP bic registered
NET: Registered protocol family 1
NET: Registered protocol family 17
yaffs: dev is 32505863 name is "mtdblock7"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.7, "mtdblock7"
VFS: Mounted root (yaffs2 filesystem).
Freeing init memory: 76K
init started:  BusyBox v1.1.2 (2008.04.19-03:06+0000) multi-call binary
Execute /home/yx5531/local.rc ...
yaffs: dev is 32505865 name is "mtdblock9"
yaffs: passed flags ""
yaffs: Attempting MTD mount on 31.9, "mtdblock9"
Hisilicon Media Memory Zone Manager
HISI_DMAC-MDC040002 @Hi3560v100_OSDrv_1_0_0_2 2008-08-14 19:00:02
NETDRV_ETHV100-M03C04DB0201 @Hi3560v100_OSDrv_1_0_0_2 2008-08-14 19:00:08
hiir: init ok. ver=Feb  9 2009, 16:50:31.
YuXing modify gpio driver init successful!
gpio_int init gpio interruptible number (7)
tde: module license 'Copyright(c)' taints kernel.
TDE_MAIN_VERSION[v1.0.0.1] Build Time[Aug 14 2008, 19:12:13]
TDE_ADP_VERSION[hi3560 adp v1.0.0.3] Build Time[Aug 14 2008, 19:12:13]
DRV356X_init
Hisilicon UMAP device driver interface: v1.00
The Vou Clk Freq is 270
DRV356X_init ok
hifb info: HIFB_MAIN_VERSION[HIFB_MAIN_VERSION] Build Time[Aug 14 2008, 19:12:15]
hifb info: video:vram0_size:3403776,vram1_size:5578752
hifb info: succeed in registering the fb0: ovl0 frame buffer device
hifb info: succeed in registering the fb1: ovl1 frame buffer device
ys_upgrade v1.0.100, 2009.02.25-11:13:22 by root
BOOTTIMES="0"
do nothing
runlevel = 4
we first to debug insmod Hisi will be modify USB MODULE
usbcore: registered new driver usbfs
usbcore: registered new driver hub
Initializing MUSB Driver (2.2.2) [debug=1][gadget=yes][otg=yes]
MUSBxDRC at 0x80090000, IRQ 23
xDRC version 2.0
musbhdrc usb0: new USB bus registered, assigned bus number 1
OTG module compiling time: Aug 14 2008->19:09:24
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 1 port detected
MUSB_HCD-M05C0406 @Hi3560v100_OSDrv_1_0_0_2 2008-08-14 19:00:13
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
usbcore: registered new driver usbserial
drivers/usb/serial/usb-serial.c: USB Serial support registered for Generic
usbcore: registered new driver usbserial_generic
drivers/usb/serial/usb-serial.c: USB Serial Driver core v2.0
drivers/usb/serial/usb-serial.c: USB Serial support registered for PL-2303
usbcore: registered new driver pl2303
drivers/usb/serial/pl2303.c: Prolific PL2303 USB to serial adaptor driver v0.12
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
Starting test ...
******* runlevel=4 *********get BOOTCOUNT="(null)"
in configGet init
TVSYSTEM IS ==1
HI_MPI_DISPLAY_Gdisplay device must be enabled before enable vou device.
etAttr: internal error!
[37:yx_drv_display_open] [error] <yx_drv_display_open> HI_API_DISPLAY_GetAddr
HI_MPI_VO_SetAttr: internal error!
[41:yx_drv_videoout_open] [error] <yx_drv_videoout_open> set VO attr failed!
display device must be enabled before enable vou device.
HI_MPI_VO_SetAttr: internal error!
HI_MPI_DISPLAY_GetAttr: display device must be enabled before enable vou device.
device not openedisplay device must be enabled before enable vou device.
d!
HI_MPI_VO_SetAttr: internal error!
HI_MPI_VO_SetAttr: internal error!
[166:yx_drv_decode_open] decoder err_cover=100
HI_MPI_DISPLAY_GetAttr: internal error!
[displayOpen,40]:get displayer parameter failed
HI_MPI_DISPLAY_SetAttr: can not support macrovision mode :30

lawman

没法操作啊。能搞定，就不用上来求助了。

rxq

谢谢分享！！！

kkllo

我有个坏的谁收

bxb_0315

very good!