神舟数码DHCH800（RG100A）不断重启，能进cfe升级登录页面，是不是已经坏了？

wingo

如题，刷了这个DLINK的固件：https://www.chinadsl.net/thread-63271-1-1.html 。用了一断时间发现有点问题，有时候收不到WIFI。今天下午测底歇菜了。开始不断重启。路由界面进不去，网线老是连上断开连上断开。情况和这个兄弟一样，https://www.chinadsl.net/thread-35963-1-1.html 按住reset等power燈滅後,打開192.168.1.1 進到一個 cfe升級登陸 頁面, 用telecomadmin用户 密码nE7jA%5m能登录。然后试着重刷DLINK，还有刷了一下博达的3G路由固件，依然还是不断重启，唉。是不是坏了啊{:soso_e109:}。。本人没有TTL线···有没有方法修复啊？？如果有TTL线能不能修复呢？

wingo

来人帮帮忙{:soso_e109:}

wingo

今天又试了很多固件还是不行。不断重启。现在按REST键也没反应了，进不了CFE界面。已经在网上淘了条TTL线。拆机后PCB发现FLASH是S29的。不知道TTL线能不能搞定。谁有TTL线的相关软件？

lawman

1.刷机之前可以先刷DSL-2760U的固件，带CFE的。从此以后进入CFE不会再询问要密码，很方便。

2.刷910改版固件试试看，

你这个是不是搞错了？你的芯片别不是BCM6328的。

RG100A-AA和BA是不一样的。

wingo

lawman 发表于 2012-7-6 21:31
1.刷机之前可以先刷DSL-2760U的固件，带CFE的。从此以后进入CFE不会再询问要密码，很方便。

2.刷910改版 ...

芯片是BCM6358的，内存32M。FLASH是S29的。没有错。已经拆机确认了。现在按REST键也进不了CFE界面了，还是一直不断重启。。。刚刚TTL线回来了。大侠有没有相关教程和软件。具有代表性的帖子大侠能不能介绍一些来

wingo

连上TTL线了。。进入超级终端还是不断重启啊··呜呜呜，怎么终止它重启呢。。

超级终端的信息：

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80238018
Decompression OK!
Entry at 0x80238018
Closing network.
Starting program at 0x80238018
Linux version 2.6.8.1 (root@MOD6538) (gcc version 3.4.2) #1 Sat Sep 19 22:45:29 CST 2009
Parallel flash device: name AM29LV320MT|S29GL128N, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 4000 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29552k/32384k available (1804k kernel code, 2788k reserved, 399k data, 76k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80e00000 ... 0x80f00000>
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe020100
Can't analyze prologue code at 801d19d4
SCSI subsystem initialized
usbcore: registered new driver hub
Initializing Cryptographic API
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0000300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0001400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x801b is enabled
D%G

CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)
Build Date: Sat Sep 19 22:28:19 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128N, id 0x2201, size 16384KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x805285F0 (1209840)
Initialized Data:          0x8041DED0 - 0x8041FCF0 (7712)
BSS Area:                  0x8041FCF0 - 0x804265F0 (26880)
Local Heap:                0x804265F0 - 0x805265F0 (1048576)
Stack Area:                0x805265F0 - 0x805285F0 (8192)
Text (code) segment:       0x80401000 - 0x8041DEC4 (118468)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id Name                     : 96358VW2  
Psi size in KB                    : 24
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:e0:fc:00:e0:fc  
Ethernet PHY Type                 : Internal


一直都如此循环。停止不了

lawman

你要刷RG100A-AA的固件和CFE

wingo

lawman 发表于 2012-7-7 16:28
你要刷RG100A-AA的固件和CFE

现在一直这样循环滚动啊。不断的重启。我不知道怎么操作才能进CFE。按RESET键再开电源也不行，一直重启重启

lawman

不是按住RESET键开电源进入的么？我的是RG100A-BA的，不知道你的是怎么样的了

wingo

lawman 发表于 2012-7-7 16:49
不是按住RESET键开电源进入的么？我的是RG100A-BA的，不知道你的是怎么样的了

按RESET键无效了现在。一点用都没。一直都在重启{{cry{{