本帖最后由 jadi 于 2011-11-9 00:31 编辑 7 S; E b8 W3 L; k: I! {
; B4 l G# H0 D# K9 ~# p2 ?7 y高手们来帮看看如何给TP406改NR285PB提高CPU频率
/ D$ I+ o5 A- a, h先看TTL启动信息/ C! v# n3 p- ^* f: i) ~
Booting...
4 v0 ?) [2 M3 x [$ v, W$ y=============================
; Y6 d+ e4 u2 `4 E<Probe SPI #0 >& l/ S- U3 a; e2 n
1.Manufacture ID=0x000000c2
+ i% @6 g \( c! b% N# [2.Device ID=0x00000020
1 }5 u7 E( F" U* @3 b& \3 |3.Capacity ID=0x00000015( `& z' K7 j/ d0 S. i' H9 W- i& k" a
4.MXIC SPI (2 MByte)!$ I- l: N: p# h
5.Total sector-counts = 512(sector=4KB). |; s! C5 [+ J8 _# \* t( w* w
6.spi_flash_info[0].device_size = 21' g- l! `0 d/ v4 O$ c
. p- Q/ G! Z2 X---RealTek(RTL8196C)at 2011.01.07-12:11+0800 version v1.0a [16bit](195MHz)% @% b. k- [. D! S7 l
uncompress_app 1
6 P8 q3 T/ n, S( c4 w& z5 P1 auncompress_app 2
# R. U. R9 `$ ?0 Y3 w5 z ^0 buncompress_app 3 h$ P! a; p0 j1 `/ h; v" v6 E& Q+ [, n
uncompress_app 4
: K* l# x. e# y0 E5 v! S* |) Buncompress_app 5
K( i7 R7 q1 n" P, z7 p; qJump to image start=0x80700000...1 s. ?) T4 e7 F, j$ M3 k
jump to init
$ G2 u# b/ l" \, }gpio init
c- e, T3 F+ N5 [watchdog enable
/ ?2 ]3 H6 d2 iUUID check OK) O+ j; i0 c- `7 o
checksum OK
; C$ T8 {5 m4 _+ V4 Linit check OK6 V' U% W. E: E
Loading Run Parameters...! G5 U3 x, k5 s; U! b7 c1 ^
Parameters Are Blank!8 H3 r2 J* j& K8 m s0 ~& C1 a) Z
Loading Default Parameters...
$ |. p4 [2 C, N. epara size 1KB' ^5 ?0 Y8 l8 y
IGD-R1A2-V1.1.19CN-Netcore(NR285PB), IGD software for NR285PB, V1.1.19 Simplifie8 S4 ~- f$ c7 @$ O
d Chinese version, 2011.01.07 12:15.<br>Copyright(c) by Netcore Technology Co.Lt
+ j- \' M+ |5 e& Fd. All rights reserved.8 N7 s, k+ V- P8 t4 i8 B4 Q; ?
LAN_IP=192.168.1.1,unusemem=1154KB
- W: M" [9 C' @/ u4 g$ Q* L; n* D& S/ l# b6 m8 t, ^$ R" E
CPU频率被降低了一半 0 D \) V" D( C* D& }
就这B
1 Q/ R* g; F: i |
粤公网安备44152102000001号 
发表于 2011-11-9 00:29:25