ZXV10 H108L无线路由猫TTL线破解的问题

gb2858

我用TTF线接上电脑后开启超级终端（或securecrt），能显示启动信息，但经过很长时间启动信息还在慢慢滚动，始终不能出现#光标，请问有人知道是什么原因吗？最后的启动信息如下（似乎不断重复）：
11930:24:53 [Klogfile][Info] [(1745)KLogThread] Need to save log file, sFileName=/proc/cfg/log, BakBufDataLen=2423
11930:24:53 [FLASHRW][Info] [proc_file_mod.c(1130)file_open] open file: /proc/cfg/log
11930:24:53 [FLASHRW][Info] [proc_file_mod.c(1260)file_close] close file: /proc/cfg/log
11930:24:53 [Klogfile][Info] [(1853)KLogThread] KLogThread save log file over, ToWriteLen=0, ErrCnt=0
11930:25:27 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[456]  died  exit_code = 2 exit_status = 1
11930:25:27 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 456 exitcode = 2
11930:25:27 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp
11930:26:09 [usb_stor][Notice] [usb_storage_mgr(1373)UsbStorageTimer] 180 seconds after insmod usb-storage.ko, startup_flag=1!
11930:26:28 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[457]  died  exit_code = 2 exit_status = 1
11930:26:28 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 457 exitcode = 2
11930:26:28 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp
11930:27:29 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[458]  died  exit_code = 2 exit_status = 1
11930:27:29 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 458 exitcode = 2
11930:27:29 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp
00:00:15 [upgrade_mgr][Notice] [upgrade_mgr.c(2091)upgradeProcTime] PcStartProgram syn_version to syn version!
00:00:15 [User][Info] [syn_version.c(367)main] No Need to Syn version
00:00:15 [User][Info] [syn_version.c(497)main] syn_version over!
00:00:16 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: var/syn_version[460]  died  exit_code = 0 exit_status = 1
00:00:16 [upgrade_mgr][Info] [upgrade_mgr.c(3677)StateIdleProc] invalid MSG!0x1111
00:00:37 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[459]  died  exit_code = 2 exit_status = 1
00:00:37 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 459 exitcode = 2
00:00:37 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp
00:01:37 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[461]  died  exit_code = 2 exit_status = 1
00:01:37 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 461 exitcode = 2
00:01:37 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp

gb2858

有人知道吗？？

k2000

猫接通电源当显示：
*** Press any key to stop auto run (1 seconds) ***
按下任意键（比如：空格键），停止CFE加载，终端上将显示：
>CFE

gb2858

没看到有*** Press any key to stop auto run (1 seconds) ***，敲回车能出现登录提示，输入root后也能出#光标，但仍然不停地滚动着类似最后几行的信息：
00:01:37 [OSS][Notice] [pc.c(938)ScanProgram] sendprogstop: msntp[461]  died  exit_code = 2 exit_status = 1
00:01:37 [sntp_mgr][Info] [sntp_mgr.c(784)sntpProcMsntpSt] Process died.Msntp, pid 461 exitcode = 2
00:01:37 [sntp_mgr][Info] [sntp_mgr.c(1482)sntpStartClient] start program successful!msntp
所有命令都不起作用！！
谁来救救我。

gb2858

打开猫的电源最先出现的信息如下：
Booting...
Press '1' to enter BOOT console...
Press '2' to enter DEBUG mode......
Using Int. PHY
Hardware or Otherway Reset!
选1的话会出现<RTL867X>，然后就不动了，选2或都不选都会出现不停地滚动信息。

gb2858

终于搞定了。破解完成。原来不需要管那些继续滚动的信息，只要在#下输命令就可以了。还要提醒大家一点，用tftp服务器的时候，记得要把所有的防火墙关了。

aming

请问你的猫是啥版本的，ttl接线顺序是怎样的谢谢

gb2858

ZXV10 H108L V2.0中国电信的，接线跟“睡觉讲话”同志介绍的方法是一样的。
https://www.chinadsl.net/thread-56693-1-1.html

fj3344

不明白
帮你顶了