[原创]GT701-WG 刷RouterTech 2.96（adam2_Recovery方法）

jonathanhu

刷了Router Tech固件，后来想刷回原厂的固件，不知道怎么搞得现在只有红灯亮，
用恢复办法，到第三步， easing flash就失败了
试过能FTP进去，应该还没废吧
请教，怎么恢复呀

xhh2001

从RT 恢复官方原版，一般要用FTP 的方法把my_ipaddress 修改回192.168.0.1 ，再刷官方原版。

xhh2001

nickhuajun 发表于 2011-6-6 14:50
按照楼主的方法和固件,正常刷上去了,进FTP改IP也成功了,可是重启后,Power常亮红灯,Internet常绿,其它全灭,网 ...

电脑网卡IP 设置成自动获取试试。 LAN 口插了网线会正常亮吗？

guhjuhju

davelov5 发表于 2011-5-16 20:28
你好 为什么在recovery这一步 按紧reset再插电后我的电源灯一直是黄灯呢？
没有教程上说的红灯。。。然后就 ...

我的和你一样！已经是砖头了！！！

guhjuhju

谁能帮下忙！现在刷过RouterTech 2.965了进不去猫而且power灯总是黄色其他灯倒是很正常是绿色，还能闪动！qq：99272686

guhjuhju

本人采用的gtrecovery.exe 官方恢复英文的方法刷 RouterTech ， 刷的时候有些紧张忘记了装网线结果按重启键按了30秒power灯都没有变成红色而是黄色，后来重刷连接上网线按住重启键插上电源十秒后发现power变不成红色了一直是黄色，可gtrecovery.exe软件进度条开始走动就抱着试试看的心理继续刷最后显示完成（期间每个进度条都正常走动），结果192.168.0.1和192.168.1.1都进不去猫了！而且发现power灯怎么弄都变不成红色了！

ppbbgg110

我本来是2.93,什么都好。就是adsl宽带的速度下行只600,上行60
转行2.96
谁知。更新完之后就power 亮红灯 my_ipadress 怎么改都是192.168.0.1
恢复不了原厂的固件。
用TTL观察到以下信息。

Launching kernel LZMA decompressor.
Kernel decompressor was successful ... launching kernel.

LINUX started...
Config serial console: ttyS0,38400
Auto Detection SANGAM chip
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #
1 Mon Jan 3 01:30:14 GMT 2011
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14112k/16384k available (1696k kernel code, 2272k reserved, 131k data, 6
0k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...  unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Using 128 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.1 (2006/08/19) Phillip Lougher, lzma support by McMCC
Adam2 environment variables API installed.
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
block: 64 slots per queue, batch=16
DEBUG: Initializing the voice port management module.
DEBUG: Initialization of the voice port management module successful..
loop: loaded (max 8 devices)
Using the MAC with internal PHY
Cpmac driver is allocating buffer memory at init time.
Cpmac driver Enable TX complete interrupt
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
PPP Deflate Compression module registered
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v1.0 at 0x0040
Flash type: AMD; Manufacturer=ST (AMD-compat).
Manufacturer_ID=0x0020; Chip_ID=0x005F; Chip_Size=0x400000; Erase_Regions=0x0002

The Chief's FLASH extensions (www.RouterTech.Org): code loaded.
number of CFI chips: 1
Looking for mtd device :mtd0:
ERROR: Invalid mtd0 start,end.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.1 (1021 buckets, 8168 max) - 384 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
ipt_account 0.1.6 : Piotr Gasid硂 <quaker@barbara.eu.org>, http://www.barbara.eu
.org/~quaker/ipt_account/
netfilter PSD loaded - (c) astaro AG
ipt_recent v0.3.1: Stephen Frost <sfrost@snowman.net>.  http://snowman.net/proje
cts/ipt_recent/
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Failed to access the environment variable region:  mtd3
Failed to get base address to mtd3
Failed to access the environment variable region:  mtd3
Failed to get base address to mtd3
Failed to access the environment variable region:  mtd3
Failed to get base address to mtd3
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'HWA_3' or 'macc' or 'wan_br_mac'.
MAC Address should be in the following format: xx:xx:xx:xx:xx:xx
VFS: Cannot open root device "" or 1f:00
Please append a correct "root=" boot option
Failed to access the environment variable region: mtd3
Kernel panic: VFS: Unable to mount root fs on 1f:00



是不是需要重新刷MTD3的配置文件。


printenv 信息

memsize               0x01000000
flashsize             0x00400000
modetty0              38400,n,8,1,hw
modetty1              38400,n,8,1,hw
bootserport           tty0
cpufrequency          150000000
sysfrequency          125000000
bootloaderVersion     0.22.02
ProductID             GT701-WG
HWRevision            2A
SerialNumber          DENGonly
AEIBootVersion        0.2i
my_ipaddress          192.168.0.1
prompt                Adam2_AR7DB
firstfreeaddress      0x9401d328
req_fullrate_freq     125000000
maca                  00:e0:a0:a6:66:70
mtd0 0x90098000       0x903f0000
mtd1 0x90010090       0x90098000
mtd2 0x90000000       0x90010000
mtd3 0x903f0000       0x90400000
mtd4 0x90010000       0x903f0000
mtd0 0x900d0000       0x903e0000
mtd0                  0x90098000,0x903f0000
mtd2                  0x90000000,0x90010000
mtd1                  0x90010090,0x90098000
usb_board_mac         00:20:E0:21:XX:B9
usb_rndis_mac         00:20:E0:21:XX:BA
macb                  00:20:E0:21:XX:B7
mac_ap                00:20:E0:21:XX:BB
autoload              1
mtd4                  0x90010000,0x903f0000
usb_pid               0x6010
usb_vid               0x1668
man                   Actiontec Electronics, Inc.
prod                  Actiontec USB/Ethernet Home DSL Modem
HWA_RNDIS             00:E0:A6:66:XX:EB
HWA_HRNDIS            00:E0:A6:66:XX:E1
DSL_FEATURE_CNTL_0        0x0000020C
connection0           0x9034
DSL_PHY_CNTL_0        0x0010080
modulation            MMODE
defaults              1
autoload_timeout      25
StaticBuffer          128
memchk.sh             1
checksync.sh          1
cron_la.sh            2

theahan

    楼主的第4步（进入FTP 修改my_ipaddress 为192.168.1.1）我认为根本就没有必要。以后进adam2猫的地址是192.168.0.1，进RT猫的地址就是192.168.1.1 一般同学不要动变量，以利于以后刷其它固件。变量乱动就会有碎片，刷多了就会有莫名其妙的故障。同步不正常有个原因是MTU不正确，默认是1500，一般是1350~1490，当然也有可能是其它，比如线路不正常。