本帖最后由 chkboy 于 2011-4-17 17:23 编辑
大亚DB120－WG，单U口，误刷双U口，能正常启动，PING不通……。
主芯片：BCM6358URKFBG
FLASH：S29GL128P
BCM5325EKQMG，这个应该是交换芯片吧？
下面还有一个BCM4328KMBG不知道做什么用的。
启动信息：
CFE version 1.0.37-102.9 for BCM96358 (32bit,SP,BE)
Build Date: Thu Jan 15 20:34:16 PST 2009 (root@pclinux-lkaplan)
Copyright (C) 2000-2008 Broadcom Corporation.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Boot Address 0xbe000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-5) : 96358VW2
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1e:40:f9:72:36
PSI Size (1-64) KBytes : 64
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80276018
LZMA: Prossible old LZMA format, trying to decompress..
Decompression OK!
Entry at 0x80276018
Closing network.
Closing DMA Channels.
Starting program at 0x80276018
Linux version 2.6.8.1 (root@localhost.localdomain) (gcc version 3.4.2) #1 Tue Se
p 29 14:11:00 CST 2009
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29300k/32384k available (1944k kernel code, 3040k reserved, 507k data, 8
0k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size[16777216] sectors[128]
Flash not used for Auxillary File System
Partition ROOTFS_KRN [0xbe020000, 16384000] Blks[125: 1 .. 125]
SubPartition Image 1 [0xbe020000, 8126464] Blks[ 62: 1 .. 62]
SubPartition Image 2 [0xbe7e0000, 8257536] Blks[ 63: 63 .. 125]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1 131072 131072 0xbe000580 1024 BOOTLOADER
1 0 125 131072 16384000 0xbe020000 16384000 ROOTFS_KRN
126 0 0 0 0 0xbefc0000 0 JFFS_AUXFS
126 65536 1 131072 131072 0xbefd0000 65536 PERSISTMEM 2
127 0 1 131072 131072 0xbefe0000 65536 LOG_SCRPAD
127 65536 1 131072 131072 0xbeff0000 65536 PERSISTMEM
Blk# BlkOff Blks MemLen Partition Name
0 1408 1 1024 NVRAM
126 65536 1 65536 Config 2
127 0 1 57344 Log
127 57344 1 8192 Scratch PAD
127 65536 1 65536 Config 1
Can't analyze prologue code at 801f4934
SCSI subsystem initialized
usbcore: registered new driver hub
TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca)
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3833856]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
hub 1-0:1.0: over-current change on port 2
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x801b is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
Mirror/redirect action on
u32 classifier
input device check on
Actions configured
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 80k freed
init started: BusyBox v1.00 (2009.09.29-06:16+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2009.09.29-06:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
fuse init (API version 7.8)
fuse distribution version: 2.7.3
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Sep 29 2009 14:09:18
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1E:40:F9:72:36
Broadcom BCM6358A1 Ethernet Network Device v0.3 Sep 29 2009 14:09:18
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1E:40:F9:72:37
Broadcom BCM6358A1 USB Network Device v0.4 Sep 29 2009 14:09:20
usb0: MAC Address: 00 1E 40 F9 72 38
usb0: Host MAC Address: 00 1E 40 F9 72 39
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1E:40:F9:72:3A
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth1 Link UP.
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x1B79CF 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
ip_nat_irc: Unknown symbol needs_ip_conntrack_irc
insmod: cannot insert `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_irc
.ko': Success (2): Success
==> Bcm963xx Software Version: 3.10L.CT_10.A2pB022g.d20e <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
SIGUSR1
# Shell exited afte
BusyBox v1.00 (2009.09.29-06:16+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
#
Power灯绿色常亮，DSL灯绿色一直闪（没插线），LAN口对应的灯插线都能亮，请问这是什么问题？
|
粤公网安备44152102000001号 
发表于 2011-4-17 16:45:13
