|
|
楼主 |
发表于 2011-4-16 14:42:37
|
显示全部楼层
清空配置是指 cfe的 e a操作吗？这个操作我进行过，这是最后一次搞的情看一下：
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[125,0xbefa0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 16252928
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8026c018
下面这个是重启过程：Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
*** Board is not initialized properly ***
Press: <enter> to use current value
'-' to go previous parameter
'.' to clear the current value
'x' to exit this command
96358VW2 ------- 0
96358VW ------- 1
96358GWVG ------- 2
96358MV2G ------- 3
96358M ------- 4
96358B ------- 5
96358BGWE_OEM1 ------- 6
96359PONG ------- 7
96358SV ------- 8
Board Id (0-8) : 0
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 0 128
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[125,0xbefa0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 16252928
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 67108864 bytes (64MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:e0:fc:00:e0:fc
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x8026c018
Decompression OK!
Entry at 0x8026c018
Closing network.
Starting program at 0x8026c018
Linux version 2.6.8.1 (root@localhost) (gcc version 3.4.2) #1 Wed Oct 8 21:54:12 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 03fa0000 @ 00000000 (usable)
On node 0 totalpages: 16288
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 12192 pages, LIFO batch:2
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 256 (order 8: 2048 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61780k/65152k available (1908k kernel code, 3304k reserved, 504k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size[16777216] sectors[128]
Flash not used for Auxillary File System
Partition ROOTFS_KRN [0xbe020000, 16252928] Blks[124: 1 .. 124]
SubPartition Image 1 [0xbe020000, 8126464] Blks[ 62: 1 .. 62]
SubPartition Image 2 [0xbe7e0000, 8126464] Blks[ 62: 63 .. 124]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1 131072 131072 0xbe000580 1024 BOOTLOADER
1 0 124 131072 16252928 0xbe020000 16252928 ROOTFS_KRN
125 0 0 0 0 0xbefa0000 0 JFFS_AUXFS
125 0 1 131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1 131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1 131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801eb814
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,4521984]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
D%GBoot Address 0xbe000000
|
|
粤公网安备44152102000001号 
发表于 2011-4-16 10:18:05