咦，用zip压缩ruc的备份文件还要审核才行啊？
Router Upgrade Check 1.4.1 13/06/2011 20:10:56
Router IP: 192.168.1.1
CLI is needed
Description: HomePlusPlus500S6307MPWII
Board type: AR7WRD
Product ID: AR7WRD
Bootloader: psbl
RAM 16.0 MB
Flash (ROM) 8.0 MB
ADAM2: No
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build: 070110
Firmware version: 3.7.1_ASB
Firmware stamp: 20070110183348
CPU: MIPS 4KEc V4.8
DSP: 6.01.04.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: Yes
TIAP: No
TNETW: No
Wireless: Yes
WIFI chip: TNETW1130******这里比较奇怪，我拆开看了就是TNETW1350A******
WIFI chip conf: No
Ports: 4
Ports (according to router): N/A
Marvell (or Marvell like): Yes
NSP: 3.7.1_ASB
Manufacturers:
RNDIS:
HRNDIS:
WARNING
Cannot confirm the model number of the wireless chip.
The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again.
Select an AR7WRD PSPBOOT 4 PORT firmware.
Latest: routertech-ar7wrd-pspboot-firmware-4ports-20110502.zip
Please read the instructions that come with the firmware files before you upgrade.
Note: a later version of the firmware may exist depending on the how up to date the RUC is.
The date-stamp may be superseded, but the rest of the filename should be the same.
According to your current MTD values, you should be able to upgrade using a single firmware image.
/etc /versions
VERSION=3.7.1_ASB
BUILD=070110
BOARD=AR7WRD
FSSTAMP=20070110183348
#
/proc/wlan
cd: can't cd to /proc/wlan
#
/usr/sbin/wlan
#
/proc/ticfg/env
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00800000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT (psbl)
IPA 192.168.1.1
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90800000
BOOTCFG m:f:"mtd1"
NVS_TFTP_LOAD 1
HWA_0 00:74:04:E5:75:92
HWA_2 00:74:04:E5:75:93
HWA_3 00:74:04:E5:75:93
TR69_CR_USERNAME plugfest
TR69_CR_PASSWORD plugfest
configed 13
mtd5 0x90042000,0x90800000
Route_Enabled 1
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
vlynq_polarity low
MAC_PORT 0
mtd1 0x90020090,0x9009f000
mtd0 0x9009f000,0x90800000
autoload 0
WLAN_HWADDR 00:74:04:E5:75:94******我怀疑这里是不是手工改错了******
Max_MACs 0
mac_ap 00:74:04:E5:75:95******我怀疑这里是不是手工改错了******
cron_enable 1
configid 6
#
/proc/sys/dev/adam2/environment
cat: /proc/sys/dev/adam2/environment: No such file or directory
#
/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #3 Wed Jan 10 18:32:13 CST 2007
#
/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector : yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
#
/proc/avalanche/avsar_ver
ATM Driver version:[6.00.01.00]
DSL HAL version: [6.00.01.00]
DSP Datapump version: [6.01.04.00] Annex A
SAR HAL version: [01.07.2b]
PDSP Firmware version:[0.54]
Chipset ID: [Ohio250(7200/7100A2)]
#
/proc/interrupts
7: 14779 R4000 timer/counter [MIPS interrupt]
8: 0 unified secondary [hw0 (Avalanche Primary)]
15: 552 serial [hw0 (Avalanche Primary)]
23: 0 + SAR [hw0 (Avalanche Primary)]
27: 1616 + Cpmac Driver [hw0 (Avalanche Primary)]
29: 0 vlynq0 [hw0 (Avalanche Primary)]
31: 3 + DSL [hw0 (Avalanche Primary)]
32: 1 + USB [hw0 (Avalanche Primary)]
#
/proc/modules
tiatm 129704 c0031060 96 2
avalanche_usb 65208 c0020060 96 0 (unused)
#
/proc/flashinfo
cat: /proc/flashinfo: No such file or directory
#
/etc/PORTS
cat: /etc/PORTS: No such file or directory
#
logic:status/nspver
3.7.1_ASB
logic:status/has_marvell
1
/etc /led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
module = adsl # module = {adsl,usb,pppoe}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 200 # flash on duration in ms
param2 = 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = usb # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = wlan # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1 = 100 # blink/flash rate in ms
###################################################################### |
|Archiver|小黑屋|宽带技术网
|网站地图
发表于 2011-6-12 21:52:10
