|
|
发表于 2011-4-30 20:48:14
|
显示全部楼层
Booting...
Launching kernel LZMA decompressor.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
vlynq_polarity = low
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #
162 Mon Jan 3 01:50:03 GMT 2011
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14108k/16384k available (1726k kernel code, 2276k reserved, 111k data, 6
4k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.1 (2006/08/19) Phillip Lougher, lzma support by McMCC
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
loop: loaded (max 8 devices)
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
Default Asymmetric MTU for eth0 1500
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
AMD/Spansion chip; checking for errata; Original Chip_ID=0x007E
AMD/Spansion chip; finished checking for errata; Revised Chip_ID=0x1000
RouterTech: AMD/Spansion chip; good chip with no errata; Restored Chip_ID=0x007E
Flash type: AMD; Manufacturer=AMD.
Manufacturer_ID=0x0001; Chip_ID=0x007E; Chip_Size=0x800000; Erase_Regions=0x0002
The Chief's FLASH extensions (www.RouterTech.Org): code loaded.
number of CFI chips: 1
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0xa1000), with size (0x35f000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a1000-0x00400000 : "mtd0"
mtd: partition "mtd0" doesn't start on an erase block boundary -- force read-onl
y
Avalanche: linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x20090), with size (0x80f70).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020090-0x000a1000 : "mtd1"
mtd: partition "mtd1" doesn't start on an erase block boundary -- force read-onl
y
Avalanche: linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Avalanche: linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Avalanche: linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x20000), with size (0x3e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00400000 : "mtd4"
Avalanche: linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
Looking for mtd device :mtd6:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (512 buckets, 4096 max) - 400 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
ipt_account 0.1.6 : Piotr Gasid硂 <quaker@barbara.eu.org>, http://www.barbara.eu
.org/~quaker/ipt_account/
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
Algorithmics/MIPS FPU Emulator v1.5
Mon Jan 3 01:54:00 UTC 2011
ledcfg: reading Standard Configuration File /etc/led.conf
ledcfg: configured 19 states
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DSP binary filesize = 374282 bytes
tn7dsl_init : env var DSL_BIT_TMODE is set
ERROR DSL: Unable to register with LED module
Texas Instruments ATM driver: version:[7.01.00.10]
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
resolver: configuration tree:
Jan 3 01:54:16 cfgmgr(sar): Could not get oam_ping_interval from boot loader e
nv
Jan 3 01:54:16 cfgmgr(sar): Trying to retreive the value from Configuration
Jan 3 01:54:16 cfgmgr(sar): oamPingInterval(20)(20)
Jan 3 01:54:16 cfgmgr(ap): AP Acquiring Lock
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Jan 3 01:54:16 cfgmgr(pppoa-109): Valid Configuration Tree
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Doing BRCTL ...
addbr br0
Doing BRCTL ...
addbr br1
Doing BRCTL ...
adDefault Asymmetric MTU for br0 1500
dbr br2
Doing BRCTL ...
addbr br3
Please press Enter to activate this console. Jan 3 01:54:17 cfgmgr(resolver): s
tat successfull for /etc/resolv.conf.
Jan 3 01:54:17 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Jan 3 01:54:17 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Jan 3 01:54:17 cfgmgr(sar): DSL Polling Timer Started succesfully.
Jan 3 01:54:17 cfgmgr(fdb): Firewall NAT service started
Jan 3 01:54:17 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Jan Default Asymmetric MTU for br1 1500
3 01:54:17 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Jan 3 01:54:17 cfgmgr(ap): MAC address is : 00:74:04:e6:57:81
Default Asymmetric MTU for br2 1500
Default Asymmetric MTU for br3 1500
root: USB is disabled
Jan 3 01:54:19 cfgmgr(ap): WPA Authenticator Started
Jan 3 01:54:19 cfgmgr(lanbridge0): Bridge Created: br0
Bridge Multicasting for br0 is now Enabled.
Doing BRCTL ...
addif br0 eth0
Jan 3 01:54:21 cfgmgr(lanbridge1): Bridge Created: br1
Bridge Multicasting for br1 is now Enabled.
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
Jan 3 01:54:23 cfgmgr(lanbridge2): Bridge Created: br2
Bridge Multicasting for br2 is now Enabled.
Default Asymmetric MTU for wlan0 1500
Default Asymmetric MTU for wdsup0 1500
Default Asymmetric MTU for wdsdw0 1500
Default Asymmetric MTU for wdsdw1 1500
Default Asymmetric MTU for wdsdw2 1500
Default Asymmetric MTU for wdsdw3 1500
Jan 3 01:54:24 cfgmgr(lanbridge3): Bridge Created: br3
Bridge Multicasting for br3 is now Enabled.
Doing BRCTL ...
stp br0 off
Jan 3 01:54:26 cfgmgr(lanbridgbr0: port 1(eth0) entering forwarding state
e0): Bridge Intebr0: topology change detectedrface Added: eth, propagating0
Doing BRCTL ...
stp br1 off
Jan 3 01:54:28 initTnetwAddr: MemAddr=0xa4000000, RegAddr=0xa4080000
cfgmgr(ap): EEPROM len 473
Jan 3 01:54:28 cfgmgr(ap): ERROR: DIE ID Mismatch eeprom ID: fc015907 11171f17
TNETW ID: b80158d1 820d0a24
Jan 3 01:54:28 cfgmgr(ap): ERROR: Validate EEPROM Imdda: starting cleanup:
age failed
Jandda: cleanup finish succesfully, good-bye.
3 01:54:28 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Jan 3 01:54:28 cfgmgr(ap): NVS_TFTP_LOAD is enabled to download the correct EEP
ROM image during next boot.
Set TFTP Server Address using IPA_SVR env variable
Jan 3 01:54:28 cfgmgr(ap): Setting bootloader env NVS_TFTP_LOAD to 1
Jan 3 01:54:28 cfgmgr(ap): AP Releasing Lock
Doing BRCTL ...
stp br2 off
Doing BRCTL ...
stp br3 off
Jan 3 01:54:28 root: USB is disabled
Jan 3 01:54:28 cfgmgr(sar): DSL Carrier is down
Jan 3 01:54:28 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
BusyBox v1.18.1 (2011-01-03 01:52:40 GMT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
|
|
|Archiver|小黑屋|宽带技术网
|网站地图
