求助 RG100A刷机后只能打开WEB页面但进不了

用户已注册

一开始刷了
【上海贝尔】RG100A-AA 改版固件（基于DLink_DSL-2760U_1.04）
https://www.chinadsl.net/forum-viewthread-tid-50681-fromuid-216548.html
一切都正常
【上海贝尔】RG100A-AA Ver:1.1固件 【Bcm6358芯片】
https://www.chinadsl.net/forum-viewthread-tid-24950-fromuid-216548.html
刷了这个后就进不了web页面了
一直显示这个

下面是TTl线 信息
=========================================================
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_200_20000 entered promiscuous mode
br0: port 9(nas_0_200_20000) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_200_20000) entering forwarding state
eth0.2: MAC Address: 00:1F:A3:97:93:99
eth0.3: MAC Address: 00:1F:A3:97:93:99
eth0.4: MAC Address: 00:1F:A3:97:93:99
eth0.5: MAC Address: 00:1F:A3:97:93:99
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0 left promiscuous mode
br0: port 1(wl0) entering disabled state
device wl0.1 left promiscuous mode
br0: port 2(wl0.1) entering disabled state
device wl0.2 left promiscuous mode
br0: port 3(wl0.2) entering disabled state
device wl0.3 left promiscuous mode
br0: port 4(wl0.3) entering disabled state
device nas_0_8_35 left promiscuous mode
br0: port 5(nas_0_8_35) entering disabled state
device nas_0_0_100 left promiscuous mode
br0: port 6(nas_0_0_100) entering disabled state
device nas_0_0_35 left promiscuous mode
br0: port 7(nas_0_0_35) entering disabled state
device nas_0_0_127 left promiscuous mode
br0: port 8(nas_0_0_127) entering disabled state
device nas_0_200_20000 left promiscuous mode
br0: port 9(nas_0_200_20000) entering disabled state
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device eth0.2 entered promiscuous mode
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
device eth0.3 entered promiscuous mode
br0: port 3(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.3) entering forwarding state
device eth0.4 entered promiscuous mode
br0: port 4(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.4) entering forwarding state
device eth0.5 entered promiscuous mode
br0: port 5(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.5) entering forwarding state
device nas_0_8_35 entered promiscuous mode
br0: port 6(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_8_35) entering forwarding state
device nas_0_0_100 entered promiscuous mode
br0: port 7(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_100) entering forwarding state
device nas_0_0_35 entered promiscuous mode
br0: port 8(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_35) entering forwarding state
device nas_0_0_127 entered promiscuous mode
br0: port 9(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_0_127) entering forwarding state
device nas_0_200_20000 entered promiscuous mode
br0: port 10(nas_0_200_20000) entering learning state
br0: topology change detected, propagating
br0: port 10(nas_0_200_20000) entering forwarding state
sntp: host not found
ip_syslog_out_ops: unload
ip_syslog_out_ops: unload success
ip_syslog_out_ops: load success
blaa_dd: port mirroring config.
blaa_dd: port mirroring config.
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
algname: h323 enable
algname: rtsp enable
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_co
nntrack_l2tp.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_na
t_l2tp.ko': No such file or directory
algname: l2tp enable
algname: ipsec enable
br0: port 2(eth0.2) entering disabled state
br0: port 3(eth0.3) entering disabled state
br0: port 4(eth0.4) entering disabled state
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
              AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP1
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:  0x80401000 - 0x80529850 (1214544)
Initialized Data:          0x8041E730 - 0x80421050 (10528)
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Board Id (0-8)                    : 96358VW2
Number of MAC Addresses (1-32)    : 12
Base MAC Address                  : 00:1f:a3:97:93:99
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1]          : 1
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80257018
Decompression OK!
Entry at 0x80257018
Closing network.
Starting program at 0x80257018
Linux version 2.6.8.1 (root@liangbingtong) (gcc version 3.4.2) #1 Thu Apr 17 19:
47:37 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 4000 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29428k/32384k available (1902k kernel code, 2912k reserved, 425k data, 7
6k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12058624] : AuxFS[4194304]
Partition ROOTFS_KRN [0xbe020000,   12058624] Blks[ 92:   1 ..  92]
SubPartition Image 1 [0xbe020000,    6029312] Blks[ 46:   1 ..  46]
SubPartition Image 2 [0xbe5e0000,    6029312] Blks[ 46:  47 ..  92]
Blk# BlkOff Blks BlkSize AvailSize   MemStart     MemLen Partition Name
   0   1408    1  131072    131072 0xbe000580       1024 BOOTLOADER
   1      0   92  131072  12058624 0xbe020000   12058624 ROOTFS_KRN
  93      0   32  131072   4194304 0xbeba0000    4194304 JFFS_AUXFS
125      0    1  131072    131072 0xbefa0000     131072 LOG_SCRPAD
126 106496    1  131072    131072 0xbefda000      24576 TW_PERSISTMEM
127 106496    1  131072    131072 0xbeffa000      24576 PERSISTMEM
Can't analyze prologue code at 801ea324
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3592192]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbeba0000,4194304]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
initLed: led[0]: mask=0x400000, state=0
initLed: led[1]: mask=0x0100, state=0
initLed: led[2]: mask=0x1000000, state=0
initLed: led[3]: mask=0x0001, state=0
initLed: led[4]: mask=0x0004, state=0
initLed: led[5]: mask=0x0010, state=0
initLed: led[6]: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:  BusyBox v1.00 (2008.04.17-11:53+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5

BusyBox v1.00 (2008.04.17-11:53+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 17 2008 19:45:36
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:97:93:99
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:97:93:9A
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth0 Link UP.
BcmCfg_recover, L341:   Waiting Usb init complete
cfminit.c, L358: flgfoundusb:0
cfminit.c, L379: flgfounddisk:0
cfminit.c, L445: time:1 sec
##no usb device22
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
==func:xmlEndFtpSrvObjNode==, objName:account1
==func:xmlEndFtpSrvObjNode==, objName:account2
==func:xmlEndFtpSrvObjNode==, objName:account3
==func:xmlEndFtpSrvObjNode==, objName:srvParams
do profileCopyToTWProfile.
BcmDb_setPMapInfo: id=2
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
BcmDb_setPMapInfo: id=5
BcmDb_setPMapIfcCfgInfo: id=3
==func:xmlEndFtpSrvObjNode==, objName:account1
==func:xmlEndFtpSrvObjNode==, objName:account2
==func:xmlEndFtpSrvObjNode==, objName:account3
==func:xmlEndFtpSrvObjNode==, objName:srvParams
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x82348 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFBA64
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_devicectl: load success
ip_conntrack_rtsp v0.01 loading
ip_syslog_out_ops: load success
ip_nat_rtsp v0.01 loading
get qos queue policy type error
Enable = 1
enter QosPriorityQueueTbl::removeAllTCRules
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_8_35
Cannot find device "nas_0_8_35"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_8_46
Cannot find device "nas_0_8_46"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_100
Cannot find device "nas_0_0_100"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_35
Cannot find device "nas_0_0_35"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_0_127
Cannot find device "nas_0_0_127"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface nas_0_200_20000
Cannot find device "nas_0_200_20000"
==>   Bcm963xx Software Version: RG100A_V1.1   <==
SIOCGIFFLAGS: No such device
buffer=2.6.8.1
ip_conntrack_devicectl: unload
ip_conntrack_devicectl: unload success
-----insmod=insmod /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_d
evicectl.ko ip_begin=3232235777 ip_end=3232236030  mode=1 maxTotalNumber=4 maxCo
mputerNumber=1 maxStbNumber=0 maxCameraNumber=1 computerStatus=0 stbStatus=0 cam
eraStatus=0
ip_conntrack_devicectl: load success
ses_led_off_ex I want
ctlstate = 0x0
recv action = 0
recv event = 0x0
blinktype=0, event=0, status=0
Setting SSID "ChinaNet-one"
Setting SSID "Guest"
Setting SSID "Guest1"
Setting SSID "Guest2"
Setting country code using abbreviation: "ALL"
channel 6 selected
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device wl0.1 entered promiscuous mode
br0: port 2(wl0.1) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0.1) entering forwarding state
device wl0.2 entered promiscuous mode
br0: port 3(wl0.2) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0.2) entering forwarding state
device wl0.3 entered promiscuous mode
br0: port 4(wl0.3) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0.3) entering forwarding state
br0: port 2(wl0.1) entering disabled state
br0: port 3(wl0.2) entering disabled state
br0: port 4(wl0.3) entering disabled state
BcmRfc2684_init interface is not up nas_0_8_35!
pvc2684ctl -a -v 0.8.35 &
pvc2684d: Interface "nas_0_8_35" created sucessfully
pvc2684d: Communicating over ATM 0.8.35, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_8_35 entered promiscuous mode
br0: port 5(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 5(nas_0_8_35) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_46!
pvc2684ctl -a -v 0.8.46 &
pvc2684d: Interface "nas_0_8_46" created sucessfully
pvc2684d: Communicating over ATM 0.8.46, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
BcmRfc2684_init interface is not up nas_0_0_100!
pvc2684ctl -a -v 0.0.100 &
pvc2684d: Interface "nas_0_0_100" created sucessfully
pvc2684d: Communicating over ATM 0.0.100, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_0_100 entered promiscuous mode
br0: port 6(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_0_100) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_35!
pvc2684ctl -a -v 0.0.35 &
pvc2684d: Interface "nas_0_0_35" created sucessfully
pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_0_35 entered promiscuous mode
br0: port 7(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_35) entering forwarding state
BcmRfc2684_init interface is not up nas_0_0_127!
pvc2684ctl -a -v 0.0.127 &
pvc2684d: Interface "nas_0_0_127" created sucessfully
pvc2684d: Communicating over ATM 0.0.127, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_0_127 entered promiscuous mode
br0: port 8(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_127) entering forwarding state
BcmRfc2684_init interface is not up nas_0_200_20000!
pvc2684ctl -a -v 0.200.20000 &
pvc2684d: Interface "nas_0_200_20000" created sucessfully
pvc2684d: Communicating over ATM 0.200.20000, encapsulation: LLC
psiTraffictl = 716024404
HTB init, kernel part version 3.17
device nas_0_200_20000 entered promiscuous mode
br0: port 9(nas_0_200_20000) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_200_20000) entering forwarding state
eth0.2: MAC Address: 00:1F:A3:97:93:99
eth0.3: MAC Address: 00:1F:A3:97:93:99
eth0.4: MAC Address: 00:1F:A3:97:93:99
eth0.5: MAC Address: 00:1F:A3:97:93:99
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0 left promiscuous mode
br0: port 1(wl0) entering disabled state
device wl0.1 left promiscuous mode
br0: port 2(wl0.1) entering disabled state
device wl0.2 left promiscuous mode
br0: port 3(wl0.2) entering disabled state
device wl0.3 left promiscuous mode
br0: port 4(wl0.3) entering disabled state
device nas_0_8_35 left promiscuous mode
br0: port 5(nas_0_8_35) entering disabled state
device nas_0_0_100 left promiscuous mode
br0: port 6(nas_0_0_100) entering disabled state
device nas_0_0_35 left promiscuous mode
br0: port 7(nas_0_0_35) entering disabled state
device nas_0_0_127 left promiscuous mode
br0: port 8(nas_0_0_127) entering disabled state
device nas_0_200_20000 left promiscuous mode
br0: port 9(nas_0_200_20000) entering disabled state
device wl0 entered promiscuous mode
br0: port 1(wl0) entering learning state
br0: topology change detected, propagating
br0: port 1(wl0) entering forwarding state
device eth0.2 entered promiscuous mode
br0: port 2(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0.2) entering forwarding state
device eth0.3 entered promiscuous mode
br0: port 3(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.3) entering forwarding state
device eth0.4 entered promiscuous mode
br0: port 4(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.4) entering forwarding state
device eth0.5 entered promiscuous mode
br0: port 5(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.5) entering forwarding state
device nas_0_8_35 entered promiscuous mode
br0: port 6(nas_0_8_35) entering learning state
br0: topology change detected, propagating
br0: port 6(nas_0_8_35) entering forwarding state
device nas_0_0_100 entered promiscuous mode
br0: port 7(nas_0_0_100) entering learning state
br0: topology change detected, propagating
br0: port 7(nas_0_0_100) entering forwarding state
device nas_0_0_35 entered promiscuous mode
br0: port 8(nas_0_0_35) entering learning state
br0: topology change detected, propagating
br0: port 8(nas_0_0_35) entering forwarding state
device nas_0_0_127 entered promiscuous mode
br0: port 9(nas_0_0_127) entering learning state
br0: topology change detected, propagating
br0: port 9(nas_0_0_127) entering forwarding state
device nas_0_200_20000 entered promiscuous mode
br0: port 10(nas_0_200_20000) entering learning state
br0: topology change detected, propagating
br0: port 10(nas_0_200_20000) entering forwarding state
sntp: host not found
ip_syslog_out_ops: unload
ip_syslog_out_ops: unload success
ip_syslog_out_ops: load success
blaa_dd: port mirroring config.
blaa_dd: port mirroring config.
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
algname: h323 enable
algname: rtsp enable
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_co
nntrack_l2tp.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_na
t_l2tp.ko': No such file or directory
algname: l2tp enable
algname: ipsec enable
br0: port 2(eth0.2) entering disabled state
br0: port 3(eth0.3) entering disabled state
br0: port 4(eth0.4) entering disabled state

MINE

接TTL数据线 中止启动进入CFE
i回车
i2回车
重启RG100A-AA

telecomadmin
nE7jA%5m

用户已注册

回复 MINE 的帖子

没用！还是老样子！

x885

我的也是，终端显示MAC地址未确定，请设置bind bridge2000-1-1 0:1:41 Notice 104501 用户admin从 192.168.1.100 成功登录


Warning!!! mac address has not been set, please set it.
xml parse error: invalid xml format

wdd512

进来学习学习。

VB60

期待解决办法