【求助】j-link 接rg100a-aa jtag口，识别不出cpu

stonefive

这两天想把j-link用起来，却遇到不少问题

先是j-link没有反应，后来刷了firmware可以好了

高兴的使用H大的Brjtag 1.9o 测试
可以识别 j-link，但不能识别6358的cpu

G:\CNC\tools\brjtag1.9o\win32>brjtag.exe -probeonly /cable:2

        ===============================================
         Broadcom EJTAG Debrick Utility v1.9o-hugebird
        ===============================================


  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000000123456]

Initializing J-Link HW Ver. 8.0
Set I/O speed to 3000 KHz
Detected target Vref = 3.364V

USB TAP device has been initialized. Please confirm VREF signal connected!
Press any key to continue... ONCE target board is powered on!

Jlink TLR reset error (3)
Jlink TLR reset error (76)
Probing bus ... ====>usb write[16], usb read[-116],(st=1)
====>v3 return state[76],(8)


USB Port R/W error occur! Please reduce buffer size with /L5:1000 and try again.




jlink commander 下面显示情况
------------------------------------
SEGGER J-Link Commander V4.25a ('?' for help)
Compiled Mar  2 2011 12:24:56
DLL version V4.25a, compiled Mar  2 2011 12:24:38
Firmware: J-Link ARM V8 compiled Jan 31 2011 18:34:52
Hardware: V8.00
S/N: 805306163
Feature(s): RDI,FlashDL,FlashBP,JFlash,GDBFull
J-Link>f
Firmware: J-Link ARM V8 compiled Jan 31 2011 18:34:52
Hardware: V8.00

J-Link>st
VTarget=0.000V
ITarget=-1599mA
TCK=0 TDI=0 TDO=0 TMS=0 TRES=1 TRST=0
Supported JTAG speeds:
- 48 MHz/n, (n>=4). => 12000kHz, 9600kHz, 8000kHz, ...
- Adaptive clocking
J-Link>hwinfo
HWInfo[00] = Target power is enabled
HWInfo[02] = -1573mA    (ITarget)
HWInfo[03] = 0mA        (ITargetPeak)
HWInfo[04] = 0mA        (ITargetPeakOperation)
HWInfo[10] = 0ms        (ITargetMaxTime0)
HWInfo[11] = 0ms        (ITargetMaxTime1)
HWInfo[12] = 0ms        (ITargetMaxTime2)
J-Link>


打开猫后（jtag pin1接了vcc）
---------
SEGGER J-Link Commander V4.25a ('?' for help)
Compiled Mar  2 2011 12:24:56
DLL version V4.25a, compiled Mar  2 2011 12:24:38
Firmware: J-Link ARM V8 compiled Jan 31 2011 18:34:52
Hardware: V8.00
S/N: 805306163
Feature(s): RDI,FlashDL,FlashBP,JFlash,GDBFull
VTarget = 3.364V
Info: TotalIRLen = ?, IRPrint = 0x..000000000000000000000000

WARNING: CPU core not found.
No devices found on JTAG chain. Trying to find device on SWD.

WARNING: CPU core not found.
No device found on SWD.
Did not find any core.
Info: TotalIRLen = ?, IRPrint = 0x..000000000000000000000000

WARNING: CPU core not found.
No devices found on JTAG chain. Trying to find device on SWD.

WARNING: CPU core not found.
No device found on SWD.
Did not find any core.
J-Link>f
Firmware: J-Link ARM V8 compiled Jan 31 2011 18:34:52
Hardware: V8.00

J-Link>st
VTarget=3.364V
ITarget=-1509mA
TCK=1 TDI=0 TDO=0 TMS=0 TRES=1 TRST=1
Supported JTAG speeds:
- 48 MHz/n, (n>=4). => 12000kHz, 9600kHz, 8000kHz, ...
- Adaptive clocking
J-Link>hwinfo
HWInfo[00] = Target power is enabled
HWInfo[02] = -1496mA    (ITarget)
HWInfo[03] = 0mA        (ITargetPeak)
HWInfo[04] = 0mA        (ITargetPeakOperation)
HWInfo[10] = 0ms        (ITargetMaxTime0)
HWInfo[11] = 0ms        (ITargetMaxTime1)
HWInfo[12] = 0ms        (ITargetMaxTime2)
J-Link>


我接线有问题吗？

怎么样可以让我用j-link v8 刷新 6358的flash

antitel

接线都确定正确不？

stonefive

是这样的，jlink 送了一个20pin的延长线，刚好可以查到猫上，
猫-jlink对应关系
3-3
4-4
5-5
6-6
7-7
8-8
9-9
10-10
另外jlink pin1 接了猫的vcc

stonefive

回复 antitel 的帖子

猫-jlink对应关系
3-3
4-4
5-5
6-6
7-7
8-8
9-9
10-10
另外jlink pin1 接了猫的vcc

stonefive

接线顺序如下
rg100a -- jlink
vcc-1
3-5
5-13
7-7
9-9
gnd-gnd

路由加电，st结果如下
-----------------------------
J-Link>st
VTarget=3.287V
ITarget=0mA
TCK=1 TDI=0 TDO=1 TMS=0 TRES=1 TRST=1
Supported JTAG speeds:
- 48 MHz/n, (n>=4). => 12000kHz, 9600kHz, 8000kHz, ...
- Adaptive clocking
J-Link>

stonefive

感谢帮助我的朋友！特别感谢hotqj版大！
确认是jlink版本问题，或者需要特别设置（不要问我，我也不会）。

现在使用版本信息如下
------------------------
Firmware: J-Link ARM V8 compiled Dec  1 2009 11:42:48

接线顺序如下
-----------------
rg100a -- jlink
vcc-1
3-5
5-13
7-7
9-9
gnd-gnd

成功备份cfe和wholeflash
------------------------------
G:\>brjtag.exe -backup:cfe /cable:2

        ===============================================
         Broadcom EJTAG Debrick Utility v1.9o-hugebird
        ===============================================


  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000805306163]

Jlink get cap error (-116)
Set I/O speed to 3000 KHz
Detected target Vref = 0.0V

USB TAP device has been initialized. Please confirm VREF signal connected!
Press any key to continue... ONCE target board is powered on!

Probing bus ... >>>JL det insta =                       FFFFFF21
                        00280680
Done

Detected IR Length is 5

CPU assumed running under BIG endian

CPU Chip ID: 00000110001101011000000101111111 (0635817F)
*** Found a Broadcom manufactured BCM6358 REV 01 CPU ***

    - EJTAG IMPCODE ....... : 00000000100000011000100100000100 (00818904)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS16 MIPS32

Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor Entered Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
Detecting Flash Base Address...
Read MPI register value : 1E00000C
MPI register show Flash Access Base Addr : 1E000000

Probing Flash at Address: 0x1E000000 ...
Detected Chip ID (VenID:DevID = 017E : 2101)
*** Found a Spansion S29GL128N/P Uni  (16MB) Flash Chip from AMD/Spansion

    - Flash Chip Window Start .... : 1E000000
    - Flash Chip Window Length ... : 01000000
    - Selected Area Start ........ : 1E000000
    - Selected Area Length ....... : 00040000

*** You Selected to Backup the CFE.BIN ***

=========================
Backup Routine Started
=========================

Saving CFE.BIN.SAVED_20110305_192418 to Disk...
Done  (CFE.BIN.SAVED_20110305_192418 saved to Disk OK)

bytes written: 262144
=========================
Backup Routine Complete
=========================
elapsed time: 19 seconds


*** REQUESTED OPERATION IS COMPLETE ***



*** You Selected to Backup the WHOLEFLASH.BIN ***
=========================
Backup Routine Started
=========================
Saving WHOLEFLASH.BIN.SAVED_20110305_192805 to Disk...
Done  (WHOLEFLASH.BIN.SAVED_20110305_192805 saved to Disk OK)
bytes written: 16777216
=========================
Backup Routine Complete
=========================
elapsed time: 817 seconds

hotqj

问题解决就好。。。 (shengli:

lang30

我的brjtag 不能识别j  link

gzshy

stonefive 发表于 2011-3-5 11:40
感谢帮助我的朋友！特别感谢hotqj版大！
确认是jlink版本问题，或者需要特别设置（不要问我，我也不会）。 ...

请问如何降低jlink firmware版本？谢谢

gzshy

hotqj 发表于 2011-3-6 01:54
问题解决就好。。。 (shengli:

请问如何降低jlink firmware版本？谢谢