找回密码
 注册

QQ登录

只需一步,快速开始

查看: 5432|回复: 6

TTl线的启动代码 来看下 变砖头了 Ha910

[复制链接]
发表于 2010-8-12 13:38:29 | 显示全部楼层 |阅读模式
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
              AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80529370 (1213296)
Initialized Data:          0x8041E550 - 0x80420B80 (9776)


*** Break into CFE console ***

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-8)                    : 96358VW2  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:74:05:00:61:ee  
PSI Size (1-64) KBytes            : 24  
Flash Block Size (1-128) in KBytes: 128  
Auxillary File System Size Percent: 25  
Main Thread Number [0|1]          : 0  

udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.9 (openwrtcn@fedora) (gcc version 4.3.3 (GCC) ) #11 Fri Mar 12 10:02:55 CST 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29720k/32768k available (2057k kernel code, 3048k reserved, 365k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.287:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: Flash phys=0x1e000000, size=0x02000000, virt= 0xbe000000
Number of erase regions: 1
Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
Primary Algorithm Table at 0040
Alternative Vendor Command Set: 0000 (None)
No Alternate Algorithm Table
Vcc Minimum:  2.7 V
Vcc Maximum:  3.6 V
No Vpp line
Typical byte/word write timeout: 128 碌s
Maximum byte/word write timeout: 1024 碌s
Typical full buffer write timeout: 128 碌s
Maximum full buffer write timeout: 4096 碌s
Typical block erase timeout: 1024 ms
Maximum block erase timeout: 16384 ms
Chip erase not supported
Device size: 0x1000000 bytes (16 MiB)
Flash Device Interface description: 0x0002
  - supports x8 and x16 via BYTE# with asynchronous interface
Max. bytes in buffer write: 0x20
Number of Erase Block Regions: 1
  Erase Region #0: BlockSize 0x20000 bytes, 128 blocks
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
bootloc=5, NumEraseRegions=1.
bcm963xx: CFI does not contain boot bank location. Assuming top.
cfi->addr_unlock1 = 0x555, cfi->addr_unlock2 = 0x2aa
number of CFI chips: 1
  0: offset=0x0,size=0x0,blocks=131072
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
i=0, tagid='bc310',  matchtagid='bccfe', Not matched.
i=1, tagid='bc310',  matchtagid='bc300', Not matched.
i=2, tagid='',  matchtagid='ag306', Not matched.
i=3, tagid='310',  matchtagid='bc221', Not matched.
i=4, tagid='bc310',  matchtagid='bc310', Matched.
CRC ok.
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc310.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is 720000 offset and length 8c0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=720000, len=8C0000
0x000000720000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SQUASHFS error: squashfs_read_data failed to read block 0x604f1a
SQUASHFS error: Unable to read metadata cache entry [604f1a]
SQUASHFS error: Unable to read inode 0x277013b7
------------[ cut here ]------------
WARNING: at fs/inode.c:712 0x800a9a10()
Modules linked in:
Call Trace:[<8002fdf0>] 0x8002fdf0
[<8001950c>] 0x8001950c
[<8001950c>] 0x8001950c
[<8002ed58>] 0x8002ed58
[<800a9a10>] 0x800a9a10
[<800a9a10>] 0x800a9a10
[<800e98cc>] 0x800e98cc
[<800abd6c>] 0x800abd6c
[<800e8f08>] 0x800e8f08
[<8012b284>] 0x8012b284
[<80098264>] 0x80098264
[<800debdc>] 0x800debdc
[<800c2990>] 0x800c2990
[<8009882c>] 0x8009882c
[<800974dc>] 0x800974dc
[<800e8678>] 0x800e8678
[<800e8748>] 0x800e8748
[<80097580>] 0x80097580
[<8009767c>] 0x8009767c
[<800afe60>] 0x800afe60
[<800aff78>] 0x800aff78
[<800a1a18>] 0x800a1a18
[<8026ed00>] 0x8026ed00
[<8001c010>] 0x8001c010
[<8015bbec>] 0x8015bbec
[<8026f100>] 0x8026f100
[<80065a8c>] 0x80065a8c
[<8026e388>] 0x8026e388
[<8001e5e4>] 0x8001e5e4
[<8026e26c>] 0x8026e26c
[<8001e5d4>] 0x8001e5d4

---[ end trace ef118225dac3aae4 ]---
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00             128 mtdblock0 (driver?)
1f01             895 mtdblock1 (driver?)
1f02           15232 mtdblock2 (driver?)
1f03            8960 mtdblock3 (driver?)
1f04             128 mtdblock4 (driver?)
1f05           16128 mtdblock5 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
              AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80529370 (1213296)
Initialized Data:          0x8041E550 - 0x80420B80 (9776)


*** Break into CFE console ***

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-8)                    : 96358VW2  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:74:05:00:61:ee  
PSI Size (1-64) KBytes            : 24  
Flash Block Size (1-128) in KBytes: 128  
Auxillary File System Size Percent: 25  
Main Thread Number [0|1]          : 0  

udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
Linux version 2.6.32.9 (openwrtcn@fedora) (gcc version 4.3.3 (GCC) ) #11 Fri Mar 12 10:02:55 CST 2010
Detected Broadcom 0x6358 CPU revision a1
CPU frequency is 300 MHz
32MB of RAM installed
registering 40 GPIOs
board_bcm963xx: CFE version: 1.0.37-10.3
bootconsole [early0] enabled
CPU revision is: 0002a010 (Broadcom BCM6358)
board_bcm963xx: board name: 96358VW2
Determined physical RAM map:
memory: 02000000 @ 00000000 (usable)
Initrd not found or empty - disabling initrd
Zone PFN ranges:
  Normal   0x00000000 -> 0x00002000
Movable zone start PFN for each node
early_node_map[1] active PFN ranges
    0: 0x00000000 -> 0x00002000
Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
PID hash table entries: 128 (order: -3, 512 bytes)
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
Memory: 29720k/32768k available (2057k kernel code, 3048k reserved, 365k data, 136k init, 0k highmem)
Hierarchical RCU implementation.
NR_IRQS:128
Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
registering PCI controller with io_map_base unset
bio: create slab <bio-0> at 0
Switching to clocksource MIPS
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
NET: Registered protocol family 1
audit: initializing netlink socket (disabled)
type=2000 audit(0.287:1): initialized
squashfs: version 4.0 (2009/01/31) Phillip Lougher
Registering mini_fo version $Id$
JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
msgmni has been set to 58
io scheduler noop registered
io scheduler deadline registered (default)
gpiodev: gpio device registered with major 254
gpiodev: gpio platform device registered with access mask FFFFFFFF
bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
console [ttyS0] enabled, bootconsole disabled
console [ttyS0] enabled, bootconsole disabled
bcm963xx_flash: Flash phys=0x1e000000, size=0x02000000, virt= 0xbe000000
Number of erase regions: 1
Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
Primary Algorithm Table at 0040
Alternative Vendor Command Set: 0000 (None)
No Alternate Algorithm Table
Vcc Minimum:  2.7 V
Vcc Maximum:  3.6 V
No Vpp line
Typical byte/word write timeout: 128 碌s
Maximum byte/word write timeout: 1024 碌s
Typical full buffer write timeout: 128 碌s
Maximum full buffer write timeout: 4096 碌s
Typical block erase timeout: 1024 ms
Maximum block erase timeout: 16384 ms
Chip erase not supported
Device size: 0x1000000 bytes (16 MiB)
Flash Device Interface description: 0x0002
  - supports x8 and x16 via BYTE# with asynchronous interface
Max. bytes in buffer write: 0x20
Number of Erase Block Regions: 1
  Erase Region #0: BlockSize 0x20000 bytes, 128 blocks
bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
bootloc=5, NumEraseRegions=1.
bcm963xx: CFI does not contain boot bank location. Assuming top.
cfi->addr_unlock1 = 0x555, cfi->addr_unlock2 = 0x2aa
number of CFI chips: 1
  0: offset=0x0,size=0x0,blocks=131072
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
bcm963xx_flash: Read Signature value of CFE1CFE1
bcm963xx_flash: CFE bootloader detected
i=0, tagid='bc310',  matchtagid='bccfe', Not matched.
i=1, tagid='bc310',  matchtagid='bc300', Not matched.
i=2, tagid='',  matchtagid='ag306', Not matched.
i=3, tagid='310',  matchtagid='bc221', Not matched.
i=4, tagid='bc310',  matchtagid='bc310', Matched.
CRC ok.
bcm963xx_flash: CFE boot tag found with version 6, board type 96358VW2, and tagid bc310.
bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
bcm963xx_flash: Spare partition is 720000 offset and length 8c0000
Creating 5 MTD partitions on "bcm963xx":
0x000000000000-0x000000020000 : "CFE"
0x000000020100-0x000000100000 : "kernel"
mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
0x000000100000-0x000000fe0000 : "rootfs"
mtd: partition "rootfs" set to be root filesystem
mtd: partition "rootfs_data" created automatically, ofs=720000, len=8C0000
0x000000720000-0x000000fe0000 : "rootfs_data"
0x000000fe0000-0x000001000000 : "nvram"
0x000000020000-0x000000fe0000 : "linux"
bcm63xx_enet MII bus: probed
bcm63xx_wdt started, timer margin: 30 sec
Registered led device: adsl
Registered led device: ppp-fail
Registered led device: power
Registered led device: stop
TCP westwood registered
NET: Registered protocol family 17
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
SQUASHFS error: squashfs_read_data failed to read block 0x604f1a
SQUASHFS error: Unable to read metadata cache entry [604f1a]
SQUASHFS error: Unable to read inode 0x277013b7
------------[ cut here ]------------
WARNING: at fs/inode.c:712 0x800a9a10()
Modules linked in:
Call Trace:[<8002fdf0>] 0x8002fdf0
[<8001950c>] 0x8001950c
[<8001950c>] 0x8001950c
[<8002ed58>] 0x8002ed58
[<800a9a10>] 0x800a9a10
[<800a9a10>] 0x800a9a10
[<800e98cc>] 0x800e98cc
[<800abd6c>] 0x800abd6c
[<800e8f08>] 0x800e8f08
[<8012b284>] 0x8012b284
[<80098264>] 0x80098264
[<800debdc>] 0x800debdc
[<800c2990>] 0x800c2990
[<8009882c>] 0x8009882c
[<800974dc>] 0x800974dc
[<800e8678>] 0x800e8678
[<800e8748>] 0x800e8748
[<80097580>] 0x80097580
[<8009767c>] 0x8009767c
[<800afe60>] 0x800afe60
[<800aff78>] 0x800aff78
[<800a1a18>] 0x800a1a18
[<8026ed00>] 0x8026ed00
[<8001c010>] 0x8001c010
[<8015bbec>] 0x8015bbec
[<8026f100>] 0x8026f100
[<80065a8c>] 0x80065a8c
[<8026e388>] 0x8026e388
[<8001e5e4>] 0x8001e5e4
[<8026e26c>] 0x8026e26c
[<8001e5d4>] 0x8001e5d4

---[ end trace 6441c6107f48d952 ]---
VFS: Cannot open root device "mtdblock2" or unknown-block(31,2)
Please append a correct "root=" boot option; here are the available partitions:
1f00             128 mtdblock0 (driver?)
1f01             895 mtdblock1 (driver?)
1f02           15232 mtdblock2 (driver?)
1f03            8960 mtdblock3 (driver?)
1f04             128 mtdblock4 (driver?)
1f05           16128 mtdblock5 (driver?)
Kernel panic - not syncing: VFS: Unable to mount root fs on unknown-block(31,2)
发表于 2010-8-14 00:00:13 | 显示全部楼层
这个应该是你刷其他固件导致设备无法正常运行重复启动,刷回去兼容的固件就可以恢复正常,这个设备和贝尔rg100a是一样的东西,你可以用他的固件
 楼主| 发表于 2010-8-15 22:23:41 | 显示全部楼层
我刷好了 刷回来了  成功OPEN WRT  学会了很多 哈哈
发表于 2010-8-24 07:56:25 | 显示全部楼层
{{gangzai9{{
发表于 2010-8-24 08:13:09 | 显示全部楼层
额~~很好  最起码比我的好多了  能刷回来~~~~
恭喜恭喜~~!
发表于 2010-9-2 03:06:12 | 显示全部楼层
(daxiao:呵呵
发表于 2010-9-2 21:08:58 | 显示全部楼层
恭喜楼主刷回来了
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|宽带技术网 |网站地图 粤公网安备44152102000001号

GMT+8, 2025-5-18 03:56 , Processed in 0.047053 second(s), 3 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表