大亚DB120-B1刷机后为什么还是升级界面？

hseih

我用TTL刷机后，进入192.168.1.1还是出现升级界面，请问这是怎么回事？另外每次刷机后，都需要重新在超级终端那边再次输入电信的那个超级密码才能进入192.168.1.1。具体请参见如下图片，谢谢了先！

antitel

你把猫开电后最开始的几段输出信息贴出来。

hseih

谢谢回复，这个信息太长了，具体如下，具体如下：



BusyBox v1.00 (2008.07.14-04:11+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 02:18:26:10:0D:01
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 02:18:26:10:0D:02
Broadcom BCM6358A1 USB Network Device v0.4 Jul 14 2008 00:02:48
usb0: MAC Address: 02 18 26 10 0D 03
usb0: Host MAC Address: 02 18 26 10 0D 04
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 02:18:26:10:0D:05
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth1 Link UP.
do_page_fault() #2: sending SIGSEGV to cfm for invalid write access to
7fff8000 (epc == 2ae89d3c, ra == 2aaffa18)
SIGSEGV
# 6
6: not found
# eth1 Link DOWN.
eth1 Link UP.
eth1 Link DOWN.
eth1 Link UP.
reset
reset: not found
# reset
reset: not found
# reboot
The system is going down NOW !!
Sending SIGTERM to all processes.
Please stand by while rebooting the system.
Restarting system.


CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80528450 (1209424)
Initialized Data:          0x8041DEB0 - 0x8041FC60 (7600)
BSS Area:                  0x8041FC60 - 0x80426450 (26608)
Local Heap:                0x80426450 - 0x80526450 (1048576)
Stack Area:                0x80526450 - 0x80528450 (8192)
Text (code) segment:       0x80401000 - 0x8041DEA8 (118440)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000


Resetting Secondary CPU...
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8)                    : 96358BGWE_OEM1
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:18:26:10:0d:01
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe5e0000) ...
Code Address: 0x80010000, Entry Address: 0x80259018
Decompression OK!
Entry at 0x80259018
Closing network.
Starting program at 0x80259018
Linux version 2.6.8.1 (root@dhcppc2) (gcc version 3.4.2) #1 Mon Jul 14 00:04:40
EDT 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Not find second flash
96358BGWE_OEM1 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 4000 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29420k/32384k available (1909k kernel code, 2920k reserved, 426k data, 7
6k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12320768] : AuxFS[4063232]
Partition ROOTFS_KRN [0xbe020000,   12320768] Blks[ 94:   1 ..  94]
SubPartition Image 1 [0xbe020000,    6160384] Blks[ 47:   1 ..  47]
SubPartition Image 2 [0xbe600000,    6160384] Blks[ 47:  48 ..  94]
Blk# BlkOff Blks BlkSize AvailSize   MemStart     MemLen Partition Name
   0   1408    1  131072    131072 0xbe000580       1024 BOOTLOADER
   1      0   94  131072  12320768 0xbe020000   12320768 ROOTFS_KRN
  95      0   31  131072   4063232 0xbebe0000    4063232 JFFS_AUXFS
126 106496    1  131072    131072 0xbefda000      24576 PERSISTMEM 2
127      0    1  131072    131072 0xbefe0000     106496 LOG_SCRPAD
127 106496    1  131072    131072 0xbeffa000      24576 PERSISTMEM
Blk# BlkOff Blks  MemLen Partition Name
   0   1408    1    1024 NVRAM
126 106496    1   24576 Config 2
127      0    1   98304 Log
127  98304    1    8192 Scratch PAD
127 106496    1   24576 Config 1
Can't analyze prologue code at 801ebe04
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3481600]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbebe0000,4063232]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
hub 1-0:1.0: over-current change on port 2
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0xc007 is enabled
Invalid External Interrupt definition
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:  BusyBox v1.00 (2008.07.14-04:11+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5


BusyBox v1.00 (2008.07.14-04:11+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 02:18:26:10:0D:01
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 02:18:26:10:0D:02
Broadcom BCM6358A1 USB Network Device v0.4 Jul 14 2008 00:02:48
usb0: MAC Address: 02 18 26 10 0D 03
usb0: Host MAC Address: 02 18 26 10 0D 04
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 02:18:26:10:0D:05
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth1 Link UP.
reboot
do_page_fault() #2: sending SIGSEGV to cfm for invalid write access to
7fff8000 (epc == 2ae89d3c, ra == 2aaffa18)
SIGSEGV
# reboot
The system is going down NOW !!
Sending SIGTERM to all processes.
Terminated
Please stand by while rebooting the system.
Restarting system.


CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80528450 (1209424)
Initialized Data:          0x8041DEB0 - 0x8041FC60 (7600)
BSS Area:                  0x8041FC60 - 0x80426450 (26608)
Local Heap:                0x80426450 - 0x80526450 (1048576)
Stack Area:                0x80526450 - 0x80528450 (8192)
Text (code) segment:       0x80401000 - 0x8041DEA8 (118440)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000


Resetting Secondary CPU...
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8)                    : 96358BGWE_OEM1
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:18:26:10:0d:01
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:********
web info: Waiting for connection on socket 0.
CFE> e n
Erase nvram? (y/n):y

Resetting board...

CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 2008-05-27 16:57:32 2 (tashin@linux-server1)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB

*** Board is not initialized properly ***

Press:  <enter> to use current value
        '-' to go previous parameter
        '.' to clear the current value
        'x' to exit this command
96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
Board Id (0-8)                    :  [C
Number of MAC Addresses (1-32)    :  11
Base MAC Address                  :  02:18:26:10:0d:01
PSI Size (1-64) KBytes            :  24
Flash Block Size (1-128) in KBytes:  128
Auxillary File System Size Percent:  25
Main Thread Number [0|1]          :  0
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80528450 (1209424)
Initialized Data:          0x8041DEB0 - 0x8041FC60 (7600)
BSS Area:                  0x8041FC60 - 0x80426450 (26608)
Local Heap:                0x80426450 - 0x80526450 (1048576)
Stack Area:                0x80526450 - 0x80528450 (8192)
Text (code) segment:       0x80401000 - 0x8041DEA8 (118440)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.100 g= r=f
f=vmlinux i=bcm963xx_fs_kernel d=1 p=0
Board IP address                  : 192.168.1.1:ffffff00
Host IP address                   : 192.168.1.100
Gateway IP address                :
Run from flash/host (f/h)         : f
Default host run file name        : vmlinux
Default host flash file name      : bcm963xx_fs_kernel
Boot delay (0-9 seconds)          : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8)                    : 96358VW2
Number of MAC Addresses (1-32)    : 11
Base MAC Address                  : 02:18:26:10:0d:01
PSI Size (1-64) KBytes            : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1]          : 0

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:
PASSWD:********
web info: Waiting for connection on socket 0.
web info: Waiting for connection on socket 1.
web info: Waiting for connection on socket 0.
CFE>
Decompression OK!
Entry at 0x80259018
Closing network.
Starting program at 0x80259018
Linux version 2.6.8.1 (root@dhcppc2) (gcc version 3.4.2) #1 Mon Jul 14 00:04:40
EDT 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Not find second flash
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
  DMA zone: 4096 pages, LIFO batch:1
  Normal zone: 4000 pages, LIFO batch:1
  HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29420k/32384k available (1909k kernel code, 2920k reserved, 426k data, 7
6k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...  unavailable.
NET: Registered protocol family 16
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12320768] : AuxFS[4063232]
Partition ROOTFS_KRN [0xbe020000,   12320768] Blks[ 94:   1 ..  94]
SubPartition Image 1 [0xbe020000,    6160384] Blks[ 47:   1 ..  47]
SubPartition Image 2 [0xbe600000,    6160384] Blks[ 47:  48 ..  94]
Blk# BlkOff Blks BlkSize AvailSize   MemStart     MemLen Partition Name
   0   1408    1  131072    131072 0xbe000580       1024 BOOTLOADER
   1      0   94  131072  12320768 0xbe020000   12320768 ROOTFS_KRN
  95      0   31  131072   4063232 0xbebe0000    4063232 JFFS_AUXFS
126 106496    1  131072    131072 0xbefda000      24576 PERSISTMEM 2
127      0    1  131072    131072 0xbefe0000     106496 LOG_SCRPAD
127 106496    1  131072    131072 0xbeffa000      24576 PERSISTMEM
Blk# BlkOff Blks  MemLen Partition Name
   0   1408    1    1024 NVRAM
126 106496    1   24576 Config 2
127      0    1   98304 Log
127  98304    1    8192 Scratch PAD
127 106496    1   24576 Config 1
Can't analyze prologue code at 801ebe04
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3481600]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbebe0000,4063232]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
hub 1-0:1.0: over-current change on port 2
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x801b is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started:  BusyBox v1.00 (2008.07.14-04:11+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5


BusyBox v1.00 (2008.07.14-04:11+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.


Loading drivers and kernel modules...

atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 02:18:26:10:0D:01
Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul 14 2008 00:02:46
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 02:18:26:10:0D:02
Broadcom BCM6358A1 USB Network Device v0.4 Jul 14 2008 00:02:48
usb0: MAC Address: 02 18 26 10 0D 03
usb0: Host MAC Address: 02 18 26 10 0D 04
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 02:18:26:10:0D:05
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
do_page_fault() #2: sending SIGSEGV to cfm for invalid write access to
7fff8000 (epc == 2ae89d3c, ra == 2aaffa18)
SIGSEGV
#

YES东

用i 命令清除一下试试。不行的话重复刷两次固件