|
|
oot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12058624
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x80529860 (1214560)
Initialized Data: 0x8041E740 - 0x80421060 (10528)
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id (0-8) : 96358VW2
Number of MAC Addresses (1-32) : 11
Base MAC Address : 00:1f:a3:9b:09:4b
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
udp_send finished
No answer .auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80257018
Decompression OK!
Entry at 0x80257018
Closing network.
Starting program at 0x80257018
Linux version 2.6.8.1 (root@liangbingtong) (gcc version 3.4.2) #1 Thu Apr 17 19:47:37 CST 2008
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
fInfo.flash_rootfs_available_length = 16252928
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 29428k/32384k available (1902k kernel code, 2912k reserved, 425k data, 76k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction... unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
Computing partition layout for flash of size[16777216] sectors[128]
Flash split 25% into RootFS+Kernel[12058624] : AuxFS[4194304]
Partition ROOTFS_KRN [0xbe020000, 12058624] Blks[ 92: 1 .. 92]
SubPartition Image 1 [0xbe020000, 6029312] Blks[ 46: 1 .. 46]
SubPartition Image 2 [0xbe5e0000, 6029312] Blks[ 46: 47 .. 92]
Blk# BlkOff Blks BlkSize AvailSize MemStart MemLen Partition Name
0 1408 1 131072 131072 0xbe000580 1024 BOOTLOADER
1 0 92 131072 12058624 0xbe020000 12058624 ROOTFS_KRN
93 0 32 131072 4194304 0xbeba0000 4194304 JFFS_AUXFS
125 0 1 131072 131072 0xbefa0000 131072 LOG_SCRPAD
126 106496 1 131072 131072 0xbefda000 24576 TW_PERSISTMEM
127 106496 1 131072 131072 0xbeffa000 24576 PERSISTMEM
Can't analyze prologue code at 801ea324
SCSI subsystem initialized
usbcore: registered new driver hub
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v2.0
File system address: 0xbe020100
Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3592192]
Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbeba0000,4194304]
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x3 is enabled
WIFI: Button Interrupt 0x0 is enabled
WIFI: map_external_irq begin
SES: LED GPIO 0x8018 is enabled
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
no exited Gpio, no found Gpio To Name
initLed: led[0]: mask=0x400000, state=0
initLed: led[1]: mask=0x0100, state=0
initLed: led[2]: mask=0x1000000, state=0
initLed: led[3]: mask=0x0001, state=0
initLed: led[4]: mask=0x0004, state=0
initLed: led[5]: mask=0x0010, state=0
initLed: led[6]: mask=0x0002, state=0
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 76k freed
init started: BusyBox v1.00 (2008.04.17-11:53+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.04.17-11:53+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Apr 17 2008 19:45:36
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:9B:09:4B
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:9B:09:4C
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth0 Link UP.
BcmCfg_recover, L341: Waiting Usb init complete
cfminit.c, L358: flgfoundusb:0
cfminit.c, L379: flgfounddisk:0
cfminit.c, L445: time:1 sec
##no usb device22
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
do profileCopyToTWProfile.
xmlEndCTCfgObj(calling cfm to get appName SystemInfo, objName ctCfg
BcmDb_setPMapInfo: id=2
xmlEndPMapFltObj(calling cfm to get appName PMapCfg, objName pmapFlt
BcmDb_setPMapInfo: id=5
BcmDb_setPMapIfcCfgInfo: id=3
BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000987 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0x0 0x0
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFBA64
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000987 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_devicectl: load success
ip_conntrack_rtsp v0.01 loading
ip_syslog_out_ops: load success
ip_nat_rtsp v0.01 loading
Enable = 1
atm: Queue was not found.
atm: Queue was not found.
atm: Queue was not found.
enter QosPriorityQueueTbl::removeAllTCRules
remove tc rule:nas_0_8_81
Cannot find device "nas_0_8_81"
waninfo 8021d= -1, vlanid= -1 muxVlanId = -1
remove tc rule of the interface ppp_0_8_81_1
Cannot find device "ppp_0_8_81_1"
==> Bcm963xx Software Version: RG100A_V1.1 <==
SIOCGIFFLAGS: No such device
buffer=2.6.8.1
ip_conntrack_devicectl: unload
ip_conntrack_devicectl: unload success
-----insmod=insmod /lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_devicectl.ko ip_begin=3232235777 ip_end=3232236030 mode=1 maxTotalNumber=99 maxComputerNumber=60 maxStbNumber=0 maxCameraNumber=1 computerStatus=1 stbStatus=0 cameraStatus=0
ip_conntrack_devicectl: load success
ses_led_off_ex I want
ctlstate = 0x0
recv action = 0
recv event = 0x0
blinktype=0, event=0, status=0
Setting SSID "ChinaNet-tgaS"
Setting SSID "Guest"
Setting SSID "Guest1"
Setting SSID "Guest2"
BcmRfc2684_init interface is not up nas_0_8_81!
pvc2684ctl -a -v 0.8.81 -f &
pvc2684d: Interface "nas_0_8_81" created sucessfully
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
psiTraffictl = 716045604
have total bandwidth rule
HTB init, kernel part version 3.17
device nas_0_8_81 entered promiscuous mode
br0: port 1(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 1(nas_0_8_81) entering forwarding state
eth0.2: MAC Address: 00:1F:A3:9B:09:4B
eth0.3: MAC Address: 00:1F:A3:9B:09:4B
eth0.4: MAC Address: 00:1F:A3:9B:09:4B
eth0.5: MAC Address: 00:1F:A3:9B:09:4B
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
SIOCSIFFLAGS: Network is down
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
device eth0.2 entered promiscuous mode
br0: port 3(eth0.2) entering learning state
br0: topology change detected, propagating
br0: port 3(eth0.2) entering forwarding state
device eth0.3 entered promiscuous mode
br0: port 4(eth0.3) entering learning state
br0: topology change detected, propagating
br0: port 4(eth0.3) entering forwarding state
device eth0.4 entered promiscuous mode
br0: port 5(eth0.4) entering learning state
br0: topology change detected, propagating
br0: port 5(eth0.4) entering forwarding state
device eth0.5 entered promiscuous mode
br0: port 6(eth0.5) entering learning state
br0: topology change detected, propagating
br0: port 6(eth0.5) entering forwarding state
CT SystemLog Init Read From Flash string lenth =12296
CT SystemLog Init Read From Flash string acsloglenth =5656 secloglenth=1043
sntp: host not found
ip_syslog_out_ops: unload
ip_syslog_out_ops: unload success
blaa_dd: port mirroring config.
blaa_dd: port mirroring config.
SIOCSIFADDR: No such device
SIOCSIFNETMASK: No such device
SIOCSIFBRDADDR: No such device
algname: h323 enable
algname: rtsp enable
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_conntrack_l2tp.ko': No such file or directory
insmod: cannot open module `/lib/modules/2.6.8.1/kernel/net/ipv4/netfilter/ip_nat_l2tp.ko': No such file or directory
algname: l2tp enable
algname: ipsec enable
br0: port 4(eth0.3) entering disabled state
br0: port 5(eth0.4) entering disabled state
br0: port 6(eth0.5) entering disabled state
最后就这样~!到了
*** Press any key to stop auto run (1 seconds) ***这个地方我快速按回车进不了CFE
有人知道怎么回事??? |
|
粤公网安备44152102000001号 
发表于 2010-6-20 14:28:41
发表于 2010-6-21 20:58:20