机器信息 CFE 版本如下，高人指导一下 我怎么办才能破解，论坛里的方法均已试验过，没用才买的TTL线，但还是和论坛各位高人给出的指导知识有出入，我有点笨，希望不惜赐教，多谢。
CFE version 1.0.37-102.6 for BCM96358 (32bit,SP,BE) Build Date: Tue Aug 18 20:48:19 CST 2009 (root@g40420m) Copyright (C) 2000-2008 Broadcom Corporation. Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz CPU running TP0 Total memory: 33554432 bytes (32MB) Boot Address 0xbe000000 Board IP address
: 192.168.1.1:ffffff00
Host IP address
: 192.168.1.100
Gateway IP address
:
Run from flash/host (f/h)
: f
Default host run file name
: vmlinux
Default host flash file name
: bcm963xx_fs_kernel
Boot delay (0-9 seconds)
: 3
Boot image (0=latest, 1=previous) : 0
Board Id (0-6)
: HG522_B
Number of MAC Addresses (1-32)
: 11
Base MAC Address
: 02:10:18:01:00:01
PSI Size (1-64) KBytes
: 0
Main Thread Number [0|1]
: 0
*** Press any key to stop auto run (3 seconds) *** Auto run second count down: 0
Support Double system.
Flash boot Flag: Boot from main system! Decompression OK! Entry at 0x80269018 Closing network. Closing DMA Channels. Starting program at 0x80269018 Linux version 2.6.8.1 (root@g40420m) (gcc version 3.4.2) #136 Tue Aug 18 20:47:03 CST 2009 Flash 0 at 0xbe000000
Size : 16 MB
Regions : 1
0 : 0x00000000 - 0x00020000 * 128
CHIP96358 prom init CPU revision is: 0002a010 Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists Kernel command line: root=31:0 ro noinitrd Bootting from Main System. brcm mips: enabling icache and dcache... Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes. Primary data cache 16kB 2-way, linesize 16 bytes. PID hash table entries: 128 (order 7: 1024 bytes) Using 150.000 MHz high precision timer. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes) Inode-cache hash table entries: 4096 (order: 2, 16384 bytes) Allocating memory for DSP module core and initialization code Allocated DSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Memory: 29348k/32384k available (1893k kernel code, 2992k reserved, 506k data, 76k init, 0k highmem) Calibrating delay loop... 299.82 BogoMIPS Mount-cache hash table entries: 512 (order: 0, 4096 bytes) Checking for 'wait' instruction...
unavailable. NET: Registered protocol family 16 Can't analyze prologue code at 801e7c54 SCSI subsystem initialized usbcore: registered new driver usbfs usbcore: registered new driver hub JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc. Initializing Cryptographic API PPP generic driver version 2.4.2 NET: Registered protocol family 24 IMQ starting with 2 devices... IMQ driver loaded successfully.
Hooking IMQ before NAT on PREROUTING.
Hooking IMQ after NAT on POSTROUTING.
netconsole: not configured, aborting Using noop io scheduler atp_mtd driver v1.0 Atp Physically mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
Atp Physically mapped flash: CFI does not contain boot bank location. Assuming top. number of CFI chips: 1 cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness. l63336:Init Partition drivers/mtd_02/maps/atpbcm963xx-flash.c 101
0 block: 0x00020100 ---0x00452000
1 block: 0x005a0000 ---0x00080000
2 block: 0x00620000 ---0x00400000
3 block: 0x00a20100 ---0x00452000
drivers/mtd_02/maps/atpbcm963xx-flash.c 119 i=4
Creating 4 MTD partitions on "Atp Physically mapped flash": 0x00020100-0x00472100 : "mainlinux" mtd: partition "mainlinux" doesn't start on an erase block boundary -- force read-only 0x005a0000-0x00620000 : "defaultcfg" 0x00620000-0x00a20000 : "middware" 0x00a20100-0x00e72100 : "slavelinux" mtd: partition "slavelinux" doesn't start on an erase block boundary -- force read-only PCI: Enabling device 0000:00:0a.0 (0000 -> 0002) ehci_hcd 0000:00:0a.0: EHCI Host Controller PCI: Setting latency timer of device 0000:00:0a.0 to 64 ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300 ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1 PCI: cache line size of 32 is not supported by device 0000:00:0a.0 ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 2 ports detected ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ohci_hcd: block sizes: ed 64 td 64 PCI: Enabling device 0000:00:09.0 (0000 -> 0002) ohci_hcd 0000:00:09.0: OHCI Host Controller PCI: Setting latency timer of device 0000:00:09.0 to 64 ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400 ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected usbcore: registered new driver usblp drivers/usb_02/class/usblp.c: v0.13: USB Printer Device Class driver Initializing USB Mass Storage driver... usbcore: registered new driver usb-storage USB Mass Storage support registered. drivers/usb_02/serial/usb-serial.c: USB Serial support registered for Generic usbcore: registered new driver usbserial_generic usbcore: registered new driver usbserial drivers/usb_02/serial/usb-serial.c: USB Serial Driver core v2.0 bhal: bhal_init entry ** support LED GPIO mode. ** SES: Button GPIO 0x8023 is enabled SES: LED GPIO 0x8023 is enabled bcm963xx_serial driver v2.0 u32 classifier NET: Registered protocol family 2 IP: routing cache hash table of 512 buckets, 4Kbytes TCP: Hash tables configured (established 2048 bind 4096) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 NET: Registered protocol family 15 Bridge firewalling registered Ebtables v2.0 registered NET: Registered protocol family 8 NET: Registered protocol family 20 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com> All bugs added by David S. Miller <davem@redhat.com> VFS: Mounted root (squashfs filesystem) readonly. Freeing unused kernel memory: 76k freed init started: BusyBox v1.9.1 (2009-08-18 20:47:31 CST) starting pid 71, tty '': '/etc/init.d/rcS' Algorithmics/MIPS FPU Emulator v1.5 RCS DONE starting pid 131, tty '': '/bin/sh' BusyBox v1.9.1 (2009-08-18 20:47:31 CST) built-in shell (ash) Enter 'help' for a list of built-in commands. -/bin/sh: can't access tty; job control turned off Loading drivers and kernel modules... atmapi: module license 'Proprietary' taints kernel. blaadd: blaa_detect entry adsl: adsl_init entry Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 18 2009 20:46:13 Config Ethernet Switch Through MDIO Pseudo PHY Interface eth0: MAC Address: 00:25:68:87:4D:52 PCI: Setting latency timer of device 0000:00:01.0 to 64 PCI: Enabling device 0000:00:01.0 (0004 -> 0006) wl: srom not detected, using main memory mapped srom info (wombo board) wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000 wl0: MAC Address: 00:25:68:87:4D:53 wl0: Broadcom BCM4318 802.11 Wireless Controller 4.150.10.15.cpe2.2 fuse init (API version 7.8) fuse distribution version: 2.7.3 Daemon: 251 Waiting for cli start!|eth0 Link Up, LinkState = 0x0. - enter the msg ===enter the log |TSP_DBGetPara ok ulPort = 23 - ============Start vendor config deal.============ Welcome Visiting Huawei
Home Gateway Copyright by Huawei Technologies Co., Ltd. Login:CWMP app version: V100R002C05B018 cwmp app V1.2.3.0.0 CWMP stk version: V100R002C05B018 cwmp stk V1.2.3.0.0 bootok ConfigDefaultSsl return: 0 atmapi: prioritize receive packets ATM proc init !!! atmcmd:atmcmd available pin_string= PIN=0 accum=0
stop wsc iWsc = 0 iLltd = 0 wps_btn = 0
WIRELESS is off port_no -1 not surported, br:br0, port:wl0 device wl0 is not a slave of br0 port_no -1 not surported, br:br0, port:wl0.1 interface wl0.1 does not exist! port_no -1 not surported, br:br0, port:wl0.2 interface wl0.2 does not exist! port_no -1 not surported, br:br0, port:wl0.3 interface wl0.3 does not exist! ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCSIFHWADDR: No such device wlancmd: wlan driver adapter not found ifconfig: SIOCSIFHWADDR: No such device wlancmd: wlan driver adapter not found ifconfig: SIOCSIFHWADDR: No such device wlancmd: wlan driver adapter not found wlancmd: wlan driver adapter not found wlancmd: wlan driver adapter not found wlancmd: wlan driver adapter not found
set wlan assoc device is 32.
set wlan assoc device is 32.
set wlan assoc device is 32.
set wlan assoc device is 32.
WIRELESS is on channel 6 selected FILE: midmsg.c, LINE: 703
now
I don't init
midcom, just boot tr069
ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device ifconfig: SIOCGIFFLAGS: No such device device wl0 entered promiscuous mode br0: port 1(wl0) entering learning state br0: topology change detected, propagating br0: port 1(wl0) entering forwarding state
wlan wps enabled
wps pbc mode
cmd wps mode = client-pbc
wlan_wpswsc@4412 cfg_state=[1] wsc_mode=enabled WlMngr::startWsc: client-pbc mode ********************************************* Wi-Fi Simple Config Application - Intel Corp. Version: Build 1.0.5, November 19 2006 ********************************************* Created @ Apr
2 2008 18:07:39 Initializing stack...button monitor start...!
OK
Now starting stack get mac = 00 25 68 87 4D 53
Error, ETHCMD_ETHCONTROLPORT cannot enter ioctl
eth0.2: MAC Address: 00:25:68:87:4D:52 eth0.3: MAC Address: 00:25:68:87:4D:52 eth0.4: MAC Address: 00:25:68:87:4D:52 eth0.5: MAC Address: 00:25:68:87:4D:52 device eth0.2 entered promiscuous mode device eth0.3 entered promiscuous mode device eth0.4 entered promiscuous mode device eth0.5 entered promiscuous mode device eth0 is not a slave of br0 pvc2684d: Interface "nas_0_8_46" created sucessfully br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff pvc2684d: Communicating over ATM 0.8.46, encapsulation: LLC
V100R002C03 DHCP Client V3.01
pvc2684d: Interface "nas_0_0_32" created sucessfully br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff pvc2684d: Communicating over ATM 0.0.32, encapsulation: LLC NO UPnP @Configed Mode ******* MODE: AP with built-in Registrar and UPnP Proxy ******* WSC: Build-in Registrar, wait for start command.... WSC: Build-in Registrar, wait for start command.... device nas_0_0_32 entered promiscuous mode br0: port 6(nas_0_0_32) entering learning state br0: topology change detected, propagating br0: port 6(nas_0_0_32) entering forwarding state pvc2684d: Interface "nas_0_8_81" created sucessfully br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC device nas_0_8_81 entered promiscuous mode br0: port 7(nas_0_8_81) entering learning state br0: topology change detected, propagating br0: port 7(nas_0_8_81) entering forwarding state pvc2684d: Interface "nas_0_0_35" created sucessfully br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC device nas_0_0_35 entered promiscuous mode br0: port 8(nas_0_0_35) entering learning state br0: topology change detected, propagating br0: port 8(nas_0_0_35) entering forwarding state pvc2684d: Interface "nas_0_8_45" created sucessfully br2684_attachvcc brvcc->vlan_id 10000, brvcc->vlan_id_wan fff pvc2684d: Communicating over ATM 0.8.45, encapsulation: LLC device nas_0_8_45 entered promiscuous mode br0: port 9(nas_0_8_45) entering learning state br0: topology change detected, propagating br0: port 9(nas_0_8_45) entering forwarding state atp: cur kernel version:[2.6.8.1] ip_conntrack version 2.1 (125 buckets, 1000 max) - 352 bytes per conntrack eth0 Link Down, LinkState = 0x8. atp: Gre conn Register OK. atp: Gre nat Register OK. ip_conntrack_pptp version 2.1 loaded atp: ip_conntrack_rtsp v0.01 loading atp: ip_nat_rtsp v0.01 loading eth0 Link Up, LinkState = 0x0. DNS Server version: V100R002C05B019 dns server V1.2.5.0.1 g_ulMacFltEnable[0] Timezone is wrong in Function: SntpTzOrderByNames, Line: 323. The string of TimeZone exceed in Function: ATP_SNTP_SetVar, Line: 678. Sntp doesn't enable! Dropbear sshd starting 2 /etc/handy_dss_key... [1265] Jan 01 00:01:06 Running in background blaa_dd: port mirroring config. blaa_dd: port mirroring config.
Stop mirror atm package to eth0.5
Read upnp enable return: 0. ===bUsbconf=0====! br0: port 5(eth0.5) entering learning state br0: topology change detected, propagating br0: port 5(eth0.5) entering forwarding state
Login incorrect! Login:!!Huawei Password: ATP>start
^
ATP>vicurcfg.xml
^
ATP>192.168.1.1
^
ATP>ea
^
ATP>start
^
ATP> | 
粤公网安备44152102000001号 
发表于 2010-5-29 16:29:48
发表于 2010-5-30 14:24:44