[BCM6358]大亚DB120-WG的折腾从BCM公版-OPENWRT-电信E家

xhh2001 · 发表于 2010-11-5 11:34:10

附一个刷了DSL-2760U 1.04后的TTL 启动信息：

CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二 1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[95,0xbebe0000] Misc[126,0xbefc0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 12320768
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x805285A0 (1209760)
Initialized Data: 0x8041DD30 - 0x8041FDC0 (8336)
BSS Area: 0x8041FDC0 - 0x804265A0 (26592)
Local Heap: 0x804265A0 - 0x805265A0 (1048576)
Stack Area: 0x805265A0 - 0x805285A0 (8192)
Text (code) segment: 0x80401000 - 0x8041DD30 (118064)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.20
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-9) : 96358VW2
Number of MAC Addresses (1-32) : 24
Base MAC Address : 00:12:34:56:78:90
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 128
Auxillary File System Size Percent: 25
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x8031e000
Decompression OK!
Entry at 0x8031e000
Closing network.
Starting program at 0x8031e000
Linux version 2.6.21.5 (lijf@deb-vm) (gcc version 4.2.3) #7 Sun Sep 5 13:52:39 CST 2010
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 32 pages used for memmap
DMA zone: 0 pages reserved
DMA zone: 4064 pages, LIFO batch:0
Normal zone: 31 pages used for memmap
Normal zone: 3969 pages, LIFO batch:0
Built 1 zonelists. Total pages: 8033
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB, 2-way, linesize 16 bytes.
Synthesized TLB refill handler (21 instructions).
Synthesized TLB load handler fastpath (33 instructions).
Synthesized TLB store handler fastpath (33 instructions).
Synthesized TLB modify handler fastpath (32 instructions).
PID hash table entries: 128 (order: 7, 512 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
Memory: 28676k/32384k available (2236k kernel code, 3708k reserved, 888k data, 96k init, 0k highmem)
KLOB Pool 1 Initialized: 1048576 bytes <0x80c00000 ... 0x80d00000>
Calibrating delay loop... 297.98 BogoMIPS (lpj=148992)
Mount-cache hash table entries: 512
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe020100
registering PCI controller with io_map_base unset
SCSI subsystem initialized
usbcore: registered new interface driver usbfs
usbcore: registered new interface driver hub
usbcore: registered new device driver usb
BLOG v1.0 Initialized
NET: Registered protocol family 8
NET: Registered protocol family 20
Time: MIPS clocksource has been installed.
NET: Registered protocol family 2
IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
TCP established hash table entries: 1024 (order: 1, 8192 bytes)
TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
TCP: Hash tables configured (established 1024 bind 1024)
TCP reno registered
squashfs: version 3.2-r2 (2007/01/15) Phillip Lougher
squashfs: LZMA suppport for slax.org by jro
NTFS driver 2.1.28 [Flags: R/W].
fuse init (API version 7.8)
io scheduler noop registered (default)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: EHCI Host Controller
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:0a.0: irq 18, io mem 0xfffe1300
ehci_hcd 0000:00:0a.0: USB f.f started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: OHCI Host Controller
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:09.0: irq 13, io mem 0xfffe1400
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new interface driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
bcmxtmrt: Broadcom BCM6358A1 ATM Network Device v0.1 Sep 5 2010 13:51:14
TCP cubic registered
Initializing XFRM netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 96k freed
init started: BusyBox v1.00 (2010.09.05-05:52+0000) multi-call binary
BusyBox v1.00 (2010.09.05-05:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
-sh: can't access tty; job control turned off
Loading drivers and kernel modules...
mknod: /var/fuse: File exists
pktflow: module license 'Proprietary' taints kernel.
Broadcom Packet Flow Cache learning via BLOG enabled.
Created Proc FS /procfs/fcache
Constructed Broadcom Packet Flow Cache v0.1 Feb 26 2009 14:21:08
bcmxtmcfg: bcmxtmcfg_init entry
adsl: adsl_init entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:12:34:56:78:90
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 17 2010 15:57:41
KLOB extended to 2 pools
KLOB extended to 3 pools
KLOB extended to 4 pools
Config Ethernet Switch Through MDIO Pseudo PHY Interface
ethsw: found bcm5325e!
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:12:34:56:78:91
KLOB extended to 5 pools
Broadcom BCM6358A1 USB Network Device v0.4 Aug 17 2010 15:57:46
usb0: MAC Address: 00 12 34 56 78 92
usb0: Host MAC Address: 00 12 34 56 78 93
PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
PCI: Setting latency timer of device 0000:00:01.0 to 64
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: MAC addr from system pool. id:0x776c0000
wl0: MAC Address: 00:12:34:56:78:94
wl0: Broadcom BCM4318 802.11 Wireless Controller 5.10.85.0.cpe4.402.8
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
proc file create OK for wireless lan.
eth1 Link UP.
===== Release Version 4.02L.03 (build timestamp 100817_1558) =====
wl_cnt= 1
ifconfig: br0: error fetching interface information: Device not found
ifconfig: br0: error fetching interface information: Device not found
rut_restartSamba: enter
rut_stopSamba: enter
rut_stopSamba: Smbd has not been started yet
.rut_stopSamba: Nmbd has not been started yet
.rut_startSamba: status = disable netBiosName=bezeq directoryName =bezeq utf8DirName=bezeq charset=utf8
rut_startSamba: samba disable,don't start samba
device eth0 is not a slave of br0
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device eth1 is not a slave of br0
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
KLOB extended to 6 pools
device usb0 is not a slave of br0
device usb0 entered promiscuous mode
br0: port 3(usb0) entering learning state
br0: topology change detected, propagating
br0: port 3(usb0) entering forwarding state
WLmngr Daemon is running
optarg=0 shmId=0
I am open &async_queue = 0xc00367c0<3>kill_fasync: bad magic number in fasync_struct!
wlButtonInit open gpio_fasync
success
Pasync_queue->magic = 0x4601
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
BcmAdsl_Initialize=0xC0074608, g_pFnNotifyCallback=0xC0094414
pSdramPHY=0xA1FFFFF8, 0x1B777C 0xDEADBEEF
AdslCoreSharedMemInit: shareMemAvailable=3552
AdslCoreHwReset: AdslOemDataAddr = 0xA1FF3FD4
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
KLOB extended to 7 pools
KLOB extended to 8 pools
bcmxtmrt: MAC address: 00 12 34 56 78 95
Plugin rp-pppoe.so loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
recovered previous ppp session info ppp0(0018820b6110/2293)
ip_tables: (C) 2000-2006 Netfilter Core Team
Line 0: xDSL G.994 training
device wl0 left promiscuous mode
br0: port 4(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
Virtual device wl0 asks to queue packet!
Setting SSID "---------"
Setting SSID "wl0_Guest1"
Setting SSID "wl0_Guest2"
Setting SSID "wl0_Guest3"
br0: port 4(wl0) entering disabled state
wlctl: Unsupported
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
device wl0 left promiscuous mode
br0: port 4(wl0) entering disabled state
device wl0 is not a slave of br0
device wl0 entered promiscuous mode
br0: port 4(wl0) entering learning state
br0: topology change detected, propagating
br0: port 4(wl0) entering forwarding state
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0
Line 0: ADSL G.992 started
Line 0: ADSL G.992 channel analysis
Line 0: ADSL G.992 message exchange
Line 0: ADSL link up, Path 0, us=637, ds=6143
(ssk) xDSL link up, Connection Type: ATM
PPP: ppp0 Start to connect ...
delay_run start
Initializing USB Mass Storage driver...
usbcore: registered new interface driver usb-storage
USB Mass Storage support registered.
saving ppp session info ppp0(0018820b6110/2ebb)
Using interface ppp0
Connect: ppp0 <--> atm0
Couldn't increase MTU to 1500
Couldn't increase MRU to 1500
Couldn't increase MRU to 1500
CHAP authentication succeeded: Authentication success,Welcome!
peer from calling number 00:18:82:0B:61:10 authorized
local IP address 119.*.*.*
remote IP address 119.*.*.*
primary DNS address 58.20.127.238
secondary DNS address 58.20.127.170
PPP: ppp0 Connection Up.
Netfilter messages via NETLINK v0.30.
nf_conntrack version 0.5.0 (253 buckets, 2024 max)
Primary DNS server = 58.20.127.238
Secondary DNS server = 58.20.127.170
All services associated with ppp0 are activated.

复制代码

zhangmings03 · 发表于 2010-11-5 20:30:48

终于看完了，收藏，有好多固件的链接\(^o^)/~

cxc_701 · 发表于 2010-11-5 22:54:09

LZ太强悍了！牛
图文并茂！真不错

xxf101 · 发表于 2010-11-8 21:45:39

不知道到底刷哪个好

arty · 发表于 2010-11-9 21:54:10

楼主太强了，不顶不行

lxyzzzg · 发表于 2010-11-12 03:57:35

楼主能不能总结一下，拿个DB120-GW来，要怎么判断哪种情况必须用TTL线刷，哪种可以只用网线刷呢？能用楼主目前最满意的DLINK固件：DLINK 2740B 3.03 来说明一下吗？

xhh2001 · 发表于 2010-11-12 08:41:29

回复 lxyzzzg 的帖子

一般来说，DB120-WG 刷固件，有带CFE 的和不带CFE 的两种，刷了带CFE 的固件后，都要用TTL线进行BOARD ID 等参数的设置。不带CFE 的固件也有和CFE 固件版本的配合问题，部分也要修改参数，像DLINK 2740B 系列的固件，一定要把BOARD ID 改为9358GW 才行，而其他电信原版、BCM公版、DSL-2650和2760U、USR9113 等BOARD ID 要改为9358VW2 才行。

为了保险，还是要在TTL线刷才安全，能了解设备启动情况，便于判断和处理故障。能直接能WEB刷的固件还是很少。

lxyzzzg · 发表于 2010-11-12 14:11:11

回复 xhh2001 的帖子

老大解释很清楚，谢谢。TTL线一定要用USB的吗，能用交换机Console线（RJ-45toDB-9）改吗？

zwjwjz · 发表于 2010-11-12 19:59:38

顶顶~~我的RG100A-AA刷死了

随风逐秀 · 发表于 2010-11-15 14:46:44

把能刷的都刷完了，看你还折腾什么？

账号		自动登录	找回密码
密码			注册