[BCM6358]大亚DB120-WG的折腾从BCM公版-OPENWRT-电信E家

digabi

我也刷了这么多版本 可现在我的rg100a不能拔号 换了好多版本 的都一样 不能拔号！

pl888888

高手，谢谢发帖

maxuetao

{{gangzai13{{haha一个大亚120-WG都刷了5个版本的固件了。

改天我也要试试看。

maxuetao

看了 只能看懂几个，10.3的CFE系通过刷哪个固件刷上去的？   纯支持啊

xhh2001

继续刷刷刷：OPENWRT   Backfire 10.03 内测版（5月5日发布，OPENWRT中文论坛有针对DB120和RG100A的2个版本，文件大小： 11.38M）
再次说明，至今为止的OPENWRT 系统暂不支持内置ADSL，必须外接猫当普通路由器用（当然是功能强大的路由器），LAN4 为WAN 接入，LAN1-3 为普通网口。

还是在CFE 1.0.37-10.3 的状态下，进入CFE>，在192.168.1.1的页面 刷新固件，OPENWRT 固件刷一次即可（因为固件文件较大，时间会稍长），重启就能登录192.168.1.1 用户名 root 密码 admin
指示灯状态：电源 绿，DSL 与INTERNET 不亮（拨号成功了也不亮），LAN1-3正常，LAN4 不亮，无线灯不亮，USB 灯常亮。这一点不太方便。

直接在WAN 设置里把ADSL 账号密码输入，有绑定MAC 的，直接输入绑定的MAC ，保存并应用就行了，本人用快速设置过几次，老是拨不了号，后来恢复出厂设置（捅RESET键）后，在WAN 设置就能上网了，LAN 一般不用设置，开启无线等设置都很简单。






很多高级功能的，慢慢研究吧。

xhh2001

附一个backfire 10.03 的TTL 启动信息：
没有连接相关的信息，只能在WEB界面的“状态”-“系统日志”下查看。

1. 
   
2. CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
   
3. Build Date: 二  1月 29 07:41:15 CST 2008 (root@ZTJ)
   
4. Copyright (C) 2000-2006 Broadcom Corporation.
   
5. Boot Address 0xbe000000
   
6. Initializing Arena.
   
7. Initializing Devices.
   
8. Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
   
9. Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
   
10.               AuxFS[95,0xbebe0000] Misc[126,0xbefc0000] PSI[127,0xbefe0000]
    
11. Flash RootFS Partition Length: 12320768
    
12. 100 MB Full-Duplex (auto-neg)
    
13. CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
    
14. CPU running TP0
    
15. Total memory: 33554432 bytes (32MB)
    
16. Total memory used by CFE:  0x80401000 - 0x805285A0 (1209760)
    
17. Initialized Data:          0x8041DD30 - 0x8041FDC0 (8336)
    
18. BSS Area:                  0x8041FDC0 - 0x804265A0 (26592)
    
19. Local Heap:                0x804265A0 - 0x805265A0 (1048576)
    
20. Stack Area:                0x805265A0 - 0x805285A0 (8192)
    
21. Text (code) segment:       0x80401000 - 0x8041DD30 (118064)
    
22. Boot area (physical):      0x00529000 - 0x00569000
    
23. Relocation Factor:         I:00000000 - D:00000000
    
24. Board IP address                  : 192.168.1.1:ffffff00  
    
25. Host IP address                   : 192.168.1.159  
    
26. Gateway IP address                :   
    
27. Run from flash/host (f/h)         : h  
    
28. Default host run file name        : 308nfs6358  
    
29. Default host flash file name      : bcm963xx_fs_kernel  
    
30. Boot delay (0-9 seconds)          : 1  
    
31. Board Id (0-9)                    : 96358VW2  
    
32. Number of MAC Addresses (1-32)    : 11  
    
33. Base MAC Address                  : 00:12:34:56:78:90  
    
34. PSI Size (1-64) KBytes            : 24  
    
35. Flash Block Size (1-128) in KBytes: 128  
    
36. Auxillary File System Size Percent: 25  
    
37. Main Thread Number [0|1]          : 0  
    
38. *** Press any key to stop auto run (1 seconds) ***
    
39. Auto run second count down: 0
    
40. Booting from only image (0xbe020000) ...
    
41. Code Address: 0x80010000, Entry Address: 0x80010000
    
42. Decompression OK!
    
43. Entry at 0x80010000
    
44. Closing network.
    
45. Starting program at 0x80010000
    
46. Linux version 2.6.32.10 (openwrtcn@ip-10-242-58-208) (gcc version 4.3.3 (GCC) ) #10 Tue May 4 22:51:39 EDT 2010
    
47. Detected Broadcom 0x6358 CPU revision a1
    
48. CPU frequency is 300 MHz
    
49. 32MB of RAM installed
    
50. registering 40 GPIOs
    
51. board_bcm963xx: CFE version: 1.0.37-10.3
    
52. bootconsole [early0] enabled
    
53. CPU revision is: 0002a010 (Broadcom BCM6358)
    
54. board_bcm963xx: board name: 96358VW2
    
55. Determined physical RAM map:
    
56. memory: 02000000 @ 00000000 (usable)
    
57. Initrd not found or empty - disabling initrd
    
58. Zone PFN ranges:
    
59.   Normal   0x00000000 -> 0x00002000
    
60. Movable zone start PFN for each node
    
61. early_node_map[1] active PFN ranges
    
62.     0: 0x00000000 -> 0x00002000
    
63. Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 8128
    
64. Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
    
65. PID hash table entries: 128 (order: -3, 512 bytes)
    
66. Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
    
67. Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
    
68. Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
    
69. Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
    
70. Memory: 29680k/32768k available (2096k kernel code, 3088k reserved, 365k data, 136k init, 0k highmem)
    
71. Hierarchical RCU implementation.
    
72. NR_IRQS:128
    
73. Calibrating delay loop... 299.00 BogoMIPS (lpj=598016)
    
74. Mount-cache hash table entries: 512
    
75. NET: Registered protocol family 16
    
76. Success to register irq 35 for button reset.
    
77. Create /proc/button_reset success.
    
78. registering PCI controller with io_map_base unset
    
79. bio: create slab <bio-0> at 0
    
80. Switching to clocksource MIPS
    
81. PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
    
82. ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
    
83. NET: Registered protocol family 2
    
84. IP route cache hash table entries: 1024 (order: 0, 4096 bytes)
    
85. TCP established hash table entries: 1024 (order: 1, 8192 bytes)
    
86. TCP bind hash table entries: 1024 (order: 0, 4096 bytes)
    
87. TCP: Hash tables configured (established 1024 bind 1024)
    
88. TCP reno registered
    
89. NET: Registered protocol family 1
    
90. audit: initializing netlink socket (disabled)
    
91. type=2000 audit(0.295:1): initialized
    
92. squashfs: version 4.0 (2009/01/31) Phillip Lougher
    
93. Registering mini_fo version $Id$
    
94. JFFS2 version 2.2. (NAND) (SUMMARY)  漏 2001-2006 Red Hat, Inc.
    
95. msgmni has been set to 57
    
96. io scheduler noop registered
    
97. io scheduler deadline registered (default)
    
98. gpiodev: gpio device registered with major 254
    
99. gpiodev: gpio platform device registered with access mask FFFFFFFF
    
100. 蔯onsole [ttyS0] enabled, bootconsole disabled= 10) is a bcm63xx_uart
     
101. console [ttyS0] enabled, bootconsole disabled
     
102. bcm963xx_flash: Flash phys=0x1e000000, size=0x02000000, virt= 0xbe000000
     
103. Number of erase regions: 1
     
104. Primary Vendor Command Set: 0002 (AMD/Fujitsu Standard)
     
105. Primary Algorithm Table at 0040
     
106. Alternative Vendor Command Set: 0000 (None)
     
107. No Alternate Algorithm Table
     
108. Vcc Minimum:  2.7 V
     
109. Vcc Maximum:  3.6 V
     
110. No Vpp line
     
111. Typical byte/word write timeout: 64 碌s
     
112. Maximum byte/word write timeout: 512 碌s
     
113. Typical full buffer write timeout: 64 碌s
     
114. Maximum full buffer write timeout: 2048 碌s
     
115. Typical block erase timeout: 512 ms
     
116. Maximum block erase timeout: 4096 ms
     
117. Typical chip erase timeout: 524288 ms
     
118. Maximum chip erase timeout: 2097152 ms
     
119. Device size: 0x1000000 bytes (16 MiB)
     
120. Flash Device Interface description: 0x0002
     
121.   - supports x8 and x16 via BYTE# with asynchronous interface
     
122. Max. bytes in buffer write: 0x40
     
123. Number of Erase Block Regions: 1
     
124.   Erase Region #0: BlockSize 0x20000 bytes, 128 blocks
     
125. bcm963xx: Found 1 x16 devices at 0x0 in 16-bit bank
     
126. Amd/Fujitsu Extended Query Table at 0x0040
     
127. bootloc=5, NumEraseRegions=1.
     
128. bcm963xx: CFI does not contain boot bank location. Assuming top.
     
129. cfi->addr_unlock1 = 0x555, cfi->addr_unlock2 = 0x2aa
     
130. number of CFI chips: 1
     
131. 0: offset=0x0,size=0x0,blocks=131072
     
132. cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
     
133. bcm963xx_flash: Read Signature value of CFE1CFE1
     
134. bcm963xx_flash: CFE bootloader detected
     
135. bcm963xx_flash: CFE boot tag found with version 6 and board type 96358VW2
     
136. bcm963xx_flash: Partition 0 is CFE offset 0 and length 20000
     
137. bcm963xx_flash: Partition 1 is kernel offset 20100 and length dff00
     
138. bcm963xx_flash: Partition 2 is rootfs offset 100000 and length ee0000
     
139. bcm963xx_flash: Partition 3 is nvram offset fe0000 and length 20000
     
140. bcm963xx_flash: Partition 4 is linux offset 20000 and length fc0000
     
141. bcm963xx_flash: Spare partition is b80000 offset and length 460000
     
142. Creating 5 MTD partitions on "bcm963xx":
     
143. 0x000000000000-0x000000020000 : "CFE"
     
144. 0x000000020100-0x000000100000 : "kernel"
     
145. mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
     
146. 0x000000100000-0x000000fe0000 : "rootfs"
     
147. mtd: partition "rootfs" set to be root filesystem
     
148. mtd: partition "rootfs_data" created automatically, ofs=B80000, len=460000
     
149. 0x000000b80000-0x000000fe0000 : "rootfs_data"
     
150. 0x000000fe0000-0x000001000000 : "nvram"
     
151. 0x000000020000-0x000000fe0000 : "linux"
     
152. bcm63xx_enet MII bus: probed
     
153. bcm63xx_wdt started, timer margin: 30 sec
     
154. Registered led device: adsl
     
155. Registered led device: ppp-fail
     
156. Registered led device: power
     
157. Registered led device: stop
     
158. TCP westwood registered
     
159. NET: Registered protocol family 17
     
160. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
161. All bugs added by David S. Miller <davem@redhat.com>
     
162. VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
     
163. Freeing unused kernel memory: 136k freed
     
164. Please be patient, while OpenWrt loads ...
     
165. - preinit -
     
166. Press the [f] key and hit [enter] to enter failsafe mode
     
167. - regular preinit -
     
168. switching to jffs2
     
169. mini_fo: using base directory: /
     
170. mini_fo: using storage directory: /overlay
     
171. - init -
     
172. Please press Enter to activate this console. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
     
173. bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
     
174. PPP generic driver version 2.4.2
     
175. NET: Registered protocol family 24
     
176. eth0: link UP - 100/full - flow control off
     
177. eth1: link forced UP - 100/full - flow control off/off
     
178. device eth1 entered promiscuous mode
     
179. br-lan: port 1(eth1) entering forwarding state
     
180. Generic kernel compatibility enabled based on linux-next next-20100113
     
181. cfg80211: Calling CRDA to update world regulatory domain
     
182. SCSI subsystem initialized
     
183. roboswitch: Probing device eth0: Failed to enable switch
     
184. roboswitch: Probing device eth1: found a 5325! It's a 5350.
     
185. eth0: link DOWN
     
186. cfg80211: World regulatory domain updated:
     
187.     (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp)
     
188.     (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     
189.     (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
     
190.     (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm)
     
191.     (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     
192.     (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm)
     
193. usbcore: registered new interface driver usbfs
     
194. usbcore: registered new interface driver hub
     
195. eth0: link UP - 100/full - flow control off
     
196. usbcore: registered new device driver usb
     
197. b43-phy0: Broadcom 4318 WLAN found (core revision 9)
     
198. Registered led device: b43-phy0::tx
     
199. Registered led device: b43-phy0::rx
     
200. Registered led device: b43-phy0::radio
     
201. Broadcom 43xx driver loaded [ Features: PL, Firmware-ID: FW13 ]
     
202. NTFS driver 2.1.29 [Flags: R/O MODULE].
     
203. ip_tables: (C) 2000-2006 Netfilter Core Team
     
204. ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
     
205. bcm63xx_ehci bcm63xx_ehci.0: BCM63XX integrated EHCI controller
     
206. bcm63xx_ehci bcm63xx_ehci.0: new USB bus registered, assigned bus number 1
     
207. bcm63xx_ehci bcm63xx_ehci.0: irq 18, io mem 0xfffe1300
     
208. bcm63xx_ehci bcm63xx_ehci.0: USB 2.0 started, EHCI 1.00
     
209. usb usb1: configuration #1 chosen from 1 choice
     
210. hub 1-0:1.0: USB hub found
     
211. hub 1-0:1.0: 2 ports detected
     
212. nf_conntrack version 0.5.0 (465 buckets, 1860 max)
     
213. CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
     
214. nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
     
215. sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
     
216. IMQ driver loaded successfully.
     
217.         Hooking IMQ before NAT on PREROUTING.
     
218.         Hooking IMQ after NAT on POSTROUTING.
     
219. xt_time: kernel timezone is -0000
     
220. ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
     
221. bcm63xx_ohci bcm63xx_ohci.0: BCM63XX integrated OHCI controller
     
222. bcm63xx_ohci bcm63xx_ohci.0: new USB bus registered, assigned bus number 2
     
223. bcm63xx_ohci bcm63xx_ohci.0: irq 13, io mem 0xfffe1400
     
224. usb usb2: configuration #1 chosen from 1 choice
     
225. hub 2-0:1.0: USB hub found
     
226. hub 2-0:1.0: 1 port detected
     
227. uhci_hcd: USB Universal Host Controller Interface driver
     
228. usbcore: registered new interface driver usblp
     
229. Initializing USB Mass Storage driver...
     
230. usbcore: registered new interface driver usb-storage
     
231. USB Mass Storage support registered.
     
232. fuse init (API version 7.13)
     
233. b43 ssb0:0: firmware: requesting b43/ucode5.fw
     
234. b43 ssb0:0: firmware: requesting b43/pcm5.fw
     
235. b43 ssb0:0: firmware: requesting b43/b0g0initvals5.fw
     
236. b43 ssb0:0: firmware: requesting b43/b0g0bsinitvals5.fw
     
237. b43-phy0: Loading firmware version 478.104 (2008-07-01 00:50:23)
     
238. device wlan0 entered promiscuous mode
     
239. br-lan: port 2(wlan0) entering forwarding state
     
240. device wlan0 left promiscuous mode
     
241. br-lan: port 2(wlan0) entering disabled state
     
242. device wlan0 entered promiscuous mode
     
243. br-lan: port 2(wlan0) entering forwarding state
     
244. 
     

复制代码

-------------系统日志-----------------

1. 
   
2. May  5 10:53:15 OpenWrt daemon.info pppd[2314]: Plugin rp-pppoe.so loaded.
   
3. May  5 10:53:15 OpenWrt daemon.notice pppd[2318]: pppd 2.4.4 started by root, uid 0
   
4. May  5 10:53:15 OpenWrt daemon.info pppd[2318]: PPP session is 8438
   
5. May  5 10:53:15 OpenWrt daemon.info pppd[2318]: Using interface ppp0
   
6. May  5 10:53:15 OpenWrt daemon.notice pppd[2318]: Connect: ppp0 <--> eth0
   
7. May  5 10:53:16 OpenWrt daemon.info dnsmasq[1609]: exiting on receipt of SIGTERM
   
8. May  5 10:53:16 OpenWrt user.info kernel: eth0: link UP - 100/full - flow control off
   
9. May  5 10:53:18 OpenWrt daemon.info pppd[2318]: CHAP authentication succeeded: Authentication success,Welcome!
   
10. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: CHAP authentication succeeded
    
11. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: peer from calling number 00:18:82:0B:61:10 authorized
    
12. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: local  IP address 110.*.*.*（本人隐藏）
    
13. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: remote IP address 110.*.*.1（本人隐藏）
    
14. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: primary   DNS address 58.20.127.170
    
15. May  5 10:53:18 OpenWrt daemon.notice pppd[2318]: secondary DNS address 58.20.127.238
    
16. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: started, version 2.52 cachesize 150
    
17. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: compile time options: IPv6 GNU-getopt no-DBus no-I18N DHCP TFTP
    
18. May  5 10:53:19 OpenWrt daemon.info dnsmasq-dhcp[2460]: DHCP, IP range 192.168.1.100 -- 192.168.1.250, lease time 12h
    
19. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: using local addresses only for domain lan
    
20. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: reading /tmp/resolv.conf.auto
    
21. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: using nameserver 58.20.127.238#53
    
22. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: using nameserver 58.20.127.170#53
    
23. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: using local addresses only for domain lan
    
24. May  5 10:53:19 OpenWrt daemon.info dnsmasq[2460]: read /etc/hosts - 1 addresses
    
25. May  5 10:53:19 OpenWrt daemon.info dnsmasq-dhcp[2460]: read /etc/ethers - 0 addresses
    
26. May  5 10:53:22 OpenWrt user.notice root: starting ntpclient
    
27. May  5 10:53:22 OpenWrt user.notice rdate: No usable time server found
    

复制代码

iouxm10000

楼主果然厉害啊，是不是联通红版的lan4口都不能用啊？我一直纳闷这个问题，谢谢啦。

fugui_tian

[quote]LAN4 为WAN 接入，LAN1-3 为普通网口。[/quote]
lz我有两根adsl,一根电话线进adsl口,另一根连个猫再连到LAN4口,行不行啊,你说刷那种版本最好

9345487

能用来刷hg522 c吗？