|
|
今天真是够郁闷啊，才写了一个长长贴没注意放在了固件下载区里，结果被YES东扔到了回收站，我想重新编辑下放到技术区，给YES东发了好几个信息，一个没回啊，也没没有结果。那会的好心情一下子没了，现在要我重写越想越觉着郁闷，不过，有问题要请教高人，所以还是再写一回吧！
中兴H608B V2和W300硬件方案基本相同，W300中英方双界面，而且ADSL与WAN、LAN全接入，又是WDS、QOS功能可谓超强，而H608B呢，用了电信的垃圾固件，那垃圾得都不用说了，大家都知道的了，于是早想看看W300的固件能不能用在H608BV2上，搜索坛子上，XYN大侠想到了一个更换界面文件的方法，实现了H608B能够实现WAN口PPPOE接入，确实方法很高明的了，但因为固件内部调用不同，不能实现指定IP地址和更改LAN IP后，能够正确自动获取IP地址，大家期待大侠能够早点出来更完善的固件，但大侠可能一直没有时间，好久没见露面了。今天有幸弄到H608BV2和W300各一台，手头又有编程器，于是就想到了那个人人都会想到的方法----FLASH移植大法。用热风枪将W300的FLASH吹下焊在H608B的上面，就是简单的动一下手，这当然没什么好讲的，芯片很快换好了，于是兴奋的加电试机。
我习惯测机方法，首先打开CMD，输入PING 192.168.1.1 -T，然后接收TTL线，然后加电，超级终端很快显示信息，然后PING命令显示IP地址通了，我想有戏。于是，IE里输入192.168.1.1，网页一闪，哈！W300的登陆页面出来了，ADMIN，ADMIN输入用户名和密码，进去了，速度很快。设置路由，电源灯，DSL灯，INTERNET灯都亮了，打开网页，很快显示出来，有线上网没问题了。真是让人太兴奋了！中兴原厂W300的固件，性能真不是盖的，界面简洁，功能却非常强大，而且反映速度很快，不像RG100A-AA中国联通那个固件，反映慢得要死！这时候再注意其他指示灯，两个USB灯不亮，这个感觉在情理之中，W300本身没有设计两个USB接口。WPS灯亮着，WLAN灯却不亮，按说，WPS灯不亮正常，难道是错位了，打开无线置界面，无线功能开着，不是错位了，就是有问题了。赶紧打开无线网络连接查看，果真问题来了，没有发现H608B的无线ID，等于是W300的固件没有开启H608BV2的无线功能。
就这么算了，肯定不可能啊！接着查原因吧，在坛子上搜了下，有高人说，可能是MAC地址不正确造成，于是马上想到用TTL张更改MAC地址吧。结果再次连上TTL线却没有找到更改MAC地址的地方，这个不是BCM6358的固件啊，不一样的。不过，对比之前W300的调试信息看到了不同的地方。
H608B上W300FLASH的调试信息：
Basic POST completed... Success.
Last reset cause: Hardware reset (Power-on reset)
ZXV10 W300A BOOT 1.0 rev: 1.4.2.0
ZXV10 W300A board 2.0.6
(c) Copyright 2004-2005 ZTE CORPORATION. All Rights Reserved.
Press ESC for monitor...
ZXV10 W300>
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
CONFIG_AVALANCHE_VLYNQ_POLARITY_LOW
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le ([email=xia@XLVersion]xia@XLVersion[/email]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113.2) neon) #1 Mon Aug 20 17:28:11 CST 2007
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14132k/16384k available (1652k kernel code, 2252k reserved, 79k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
AVALANCHE_WATCHDOG_TIMER_BASE=a8611f00
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
cpmac_dev_init,EnableHwIGMP1
Default Asymmetric MTU for eth0 1500
Default Asymmetric MTU for eth1 1500
CPMAC: Registered switch port 1 with device eth1
Default Asymmetric MTU for eth2 1500
CPMAC: Registered switch port 2 with device eth2
Default Asymmetric MTU for eth3 1500
CPMAC: Registered switch port 3 with device eth3
Default Asymmetric MTU for eth4 1500
CPMAC: Registered switch port 4 with device eth4
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Found: SST 39VF3201
Physically mapped flash:0: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
Using word write method
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0xd0000), with size (0x320000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000d0000-0x003f0000 : "mtd0"
Avalanche: linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x40000), with size (0x90000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00040000-0x000d0000 : "mtd1"
Avalanche: linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Avalanche: linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x10000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00030000 : "mtd3"
Avalanche: linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x40000), with size (0x3b0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00040000-0x003f0000 : "mtd4"
Avalanche: linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
Avalanche: Adding a mtd5 image (0x30000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00030000-0x00040000 : "mtd5"
Avalanche: linking partition mtd5: mtd5 -> ../../mtdblock/5
Looking for mtd device :mtd6:
Avalanche: Adding a mtd6 image (0x3f0000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003f0000-0x00400000 : "mtd6"
Avalanche: linking partition mtd6: mtd6 -> ../../mtdblock/6
Looking for mtd device :mtd7:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (128 buckets, 1024 max) - 372 bytes per conntrack
ip_ct_sip: registering helper for port 5060
ip_ct_sip: registering helper for port 5063
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
urlfilter match register 0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
serial console detected. Disabling virtual terminals.
console=/dev/tts/0
init started: BusyBox v0.61.pre (2007.08.20-09:37+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
ledcfg: reading Standard Configuration File /etc/led.conf
ledcfg: configured 15 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o
USB: Entering USB_init_module.
USB Driver built for RNDIS-CDC protocols.
Error getting protocol configuration from bootloader environment.
Defaulting to "RNDIS-CDC" mode.
VID = 0x451
PID = 0x6060
No Serial Number String present.
Manufacturer = Texas Instruments
Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
USB: Entering USB_Init.
USB: Leaving USB_Init.
Default Asymmetric MTU for usb0 1500
USB: Leaving USB_init_module.
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
DSP binary filesize = 356930 bytes
tn7dsl_init : env var DSL_BIT_TMODE is set
Texas Instruments ATM driver: version:[6.00.01.00]
Waiting for enter to start '/bin/sh' (pid 38, terminal /dev/tts/0)
Please press Enter to activate this console. $$$$$$$proc_newboot_defparams
UP MOde is adsl
==== In logic main ====
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
ADSL default config is already here!
name MappingEntity
Sep 8 12:00:25 cfgmgr(tr069glue): get parametervalues(ConnectionRequestURL): http://192.168.1.1:1050/
resolver: configuration tree:
Sep 8 12:00:31 cfgmgr(sar): oamPingInterval(20)(20)
Sep 8 12:00:36 cfgmgr(resolver): stat successfull for /etc/resolv.conf.
Sep 8 12:00:36 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Sep 8 12:00:36 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Sep 8 12:00:36 cfgmgr(sar): DSL Polling Timer Started succesfully.
Sep 8 12:00:36 cfgmgr(fdb): Firewall NAT service started
Sep 8 12:00:37 VFS: Mounted root (squashfs filesystem) readonly.
Sep 8 12:00:37 : Mounted devfs on /dev
Sep 8 12:00:37 Freeing unused kernel memory: 64k freed
Sep 8 12:00:37 : Algorithmics/MIPS FPU Emulator v1.5
Sep 8 12:00:37 USB: Entering USB_init_module.
Sep 8 12:00:37 : USB Driver built for RNDIS-CDC protocols.
Sep 8 12:00:37 : Error getting protocol configuration from bootloader environment.
Sep 8 12:00:37 : Defaulting to "RNDIS-CDC" mode.
Sep 8 12:00:37 : VID = 0x451
Sep 8 12:00:37 : PID = 0x6060
Sep 8 12:00:38 cfgmgr(ap): AP Acquiring Lock
Sep 8 12:00:38 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Sep 8 12:00:38 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Sep 8 12:00:38 cfgmgr(ap): MAC address : 00:15:eb:5d:95:8d
Param InternetGatewayDevice.DeviceInfo.SoftwareVersion ===891=====PVALUE ======= V1.0.3.U01B
Sep 8 12:00:39 cfgmgr(lanbridge0): Bridge Created: br0
Sep 8 12:00:40 cfgmgr(lanbridge1): Bridge Created: br1
Sep 8 12:00:40 cfgmgr(lanbridge2): Bridge Created: br2
Sep 8 12:00:41 cfgmgr(lanbridge3): Bridge Created: br3
Sep 8 12:00:41 cfgmgr(lanbridge4): Bridge Created: br4
Sep 8 12:00:42 cfgmgr(ap): WPA Authenticator Started
Sep 8 12:00:42 cfgmgr(lanbridge0): Bridge Interface Added: eth0
WPA send hello to wlan drv
Sep 8 12:00:43 cfgmgr(lanbridge0): Bridge Interface Added: eth1
Sep 8 12:00:44 cfgmgr(lanbridge0): Bridge Interface Added: eth2
Sep 8 12:00:45 cfgmgr(lanbridge0): Bridge Interface Added: eth3
Sep 8 12:00:46 : No Serial Number String present.
Sep 8 12:00:46 : Manufacturer = Texas Instruments
Sep 8 12:00:46 : Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
Sep 8 12:00:46 USB: Entering USB_Init.
Sep 8 12:00:46 USB: Leaving USB_Init.
Sep 8 12:00:46 : Default Asymmetric MTU for usb0 1500
Sep 8 12:00:46 USB: Leaving USB_init_module.
Sep 8 12:00:46 : registered device TI Avalanche SAR
Sep 8 12:00:46 : Ohio250(7200/7100A2) detected
Sep 8 12:00:46 DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
Sep 8 12:00:46 : DSP binary filesize = 356930 bytes
Sep 8 12:00:46 cfgmgr(sar): DSL Carrier is down
Sep 8 12:00:46 tn7dsl_init : env var DSL_BIT_TMODE is set
Sep 8 12:00:46 Texas Instruments ATM driver: version:[6.00.01.00]
Sep 8 12:00:46 : Default Asymmetric MTU for br4 1500
Sep 8 12:00:46 : Bridge Multicasting for br0 is now Enabled.
Sep 8 12:00:46 : Bridge Multicasting for br1 is now Enabled.
Sep 8 12:00:46 : Bridge Multicasting for br2 is now Enabled.
Sep 8 12:00:46 : Bridge Multicasting for br3 is now Enabled.
Sep 8 12:00:46 : Bridge Multicasting for br4 is now Enabled.
hehe in pc message startlistenserver
in inetd_start_manufacture lanoip is 192.168.1.1
lano ip is 192.168.1.1
!!!!!set succeed initialize setsockopt IPPROTO_IP IP_ADD_MEMBERSHIP
in pc_Intialize_manuctureSocket manufacturefd is 11
in inetd_start_manufacture ret ==1 ,manufacture fd is 11
Sep 8 12:00:51 : Default Asymmetric MTU for wlan0 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wlan1 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wlan2 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wlan3 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wdsup0 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wdsdw0 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wdsdw1 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wdsdw2 1500
Sep 8 12:00:51 : Default Asymmetric MTU for wdsdw3 1500
Sep 8 12:00:52 cfgmgr(ap): EEPROM len 473
Sep 8 12:00:52 cfgmgr(ap): ERROR: DIE ID Mismatch eeprom ID: 38015c81 608c1b0f TNETW ID: 2c015ce3 44d30809
Sep 8 12:00:52 cfgmgr(ap): ERROR: Validate EEPROM Image failed
Sep 8 12:00:52 cfgmgr(ap): Read backup EEPROM Image!
Sep 8 12:00:52 cfgmgr(ap): EEPROM len 473
Sep 8 12:00:52 cfgmgr(ap): ERROR: DIE ID Mismatch eeprom ID: 38015c81 608c1b0f TNETW ID: 2c015ce3 44d30809
Sep 8 12:00:52 cfgmgr(ap): ERROR: Validate EEPROM Image failed
Sep 8 12:00:52 cfgmgr(ap): Retrieving EEPROM image file stdnvs_2c015ce344d30809.bin from TFTP Server 192.168.1.254 .....
tftp: timeout
tftp: timeout
tftp: timeout
tftp: timeout
tftp: timeout
tftp: timeout
tftp: last timeout
Sep 8 12:01:23 cfgmgr(ap): ERROR: TFTP of file : stdnvs_2c015ce344d30809.bin failed
Sep 8 12:01:23 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Sep 8 12:01:23 cfgmgr(ap): Set TFTP Server Address using IPA_SVR env variable to download the correct EEPROM image during next boot.
Sep 8 12:01:23 cfgmgr(ap): AP Releasing Lock
Sep 8 12:01:23 dda: starting cleanup:
Sep 8 12:01:23 dda: cleanup finish succesfully, good-bye.
^F
Starting pid 38, console /dev/tts/0: '/bin/sh'
BusyBox v0.61.pre (2007.08.20-09:37+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
# help
Built-in commands:
-------------------
. : bg break builtin cd chdir continue eval exec exit export
false fc fg hash help jobs kill local pwd read readonly return
set setvar shift times trap true type ulimit umask unset wait
# ?
?: No such file or directory
# ls
[1;34mbin[0m [1;34metc[0m [1;34mproc[0m [1;34musr[0m [0;0mvar.tar[0m
[1;34mdev[0m [1;34mlib[0m [1;34msbin[0m [1;34mvar[0m
#
Basic POST completed... Success.
Last reset cause: Hardware reset (Power-on reset)
ZXV10 W300A BOOT 1.0 rev: 1.4.2.0
ZXV10 W300A board 2.0.6
(c) Copyright 2004-2005 ZTE CORPORATION. All Rights Reserved.
Press ESC for monitor...
ZXV10 W300>
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
CONFIG_AVALANCHE_VLYNQ_POLARITY_LOW
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le ([email=xia@XLVersion]xia@XLVersion[/email]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113.2) neon) #1 Mon Aug 20 17:28:11 CST 2007
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14132k/16384k available (1652k kernel code, 2252k reserved, 79k data, 64k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
AVALANCHE_WATCHDOG_TIMER_BASE=a8611f00
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
cpmac_dev_init,EnableHwIGMP1
Default Asymmetric MTU for eth0 1500
Default Asymmetric MTU for eth1 1500
CPMAC: Registered switch port 1 with device eth1
Default Asymmetric MTU for eth2 1500
CPMAC: Registered switch port 2 with device eth2
Default Asymmetric MTU for eth3 1500
CPMAC: Registered switch port 3 with device eth3
Default Asymmetric MTU for eth4 1500
CPMAC: Registered switch port 4 with device eth4
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Found: SST 39VF3201
Physically mapped flash:0: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
Using word write method
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0xd0000), with size (0x320000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000d0000-0x003f0000 : "mtd0"
Avalanche: linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x40000), with size (0x90000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00040000-0x000d0000 : "mtd1"
Avalanche: linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Avalanche: linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x10000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00030000 : "mtd3"
Avalanche: linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x40000), with size (0x3b0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00040000-0x003f0000 : "mtd4"
Avalanche: linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
Avalanche: Adding a mtd5 image (0x30000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00030000-0x00040000 : "mtd5"
Avalanche: linking partition mtd5: mtd5 -> ../../mtdblock/5
Looking for mtd device :mtd6:
Avalanche: Adding a mtd6 image (0x3f0000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x003f0000-0x00400000 : "mtd6"
Avalanche: linking partition mtd6: mtd6 -> ../../mtdblock/6
Looking for mtd device :mtd7:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (128 buckets, 1024 max) - 372 bytes per conntrack
ip_ct_sip: registering helper for port 5060
ip_ct_sip: registering helper for port 5063
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
urlfilter match register 0
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
serial console detected. Disabling virtual terminals.
console=/dev/tts/0
init started: BusyBox v0.61.pre (2007.08.20-09:37+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/
?Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o
USB: Entering USB_init_module.
USB Driver built for RNDIS-CDC protocols.
Error getting protocol configuration from bootloader environment.
Defaultieng to "RNDIS-CDC" mode.
VID = 0x451
PID = 0x6060
No Serial Number String present.
Manufacturer = Texas Instruments
Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
USB: Entering USB_Init.
USB: Leaving USB_Init.
Default Asymmetric MTU for usb0 1500
USB: Leaving USB_init_module.
Us |
|
|Archiver|小黑屋|宽带技术网
|网站地图
发表于 2009-9-22 20:22:59