2650BU 官方固件终于出来了

flyxxt

强,不过大家注意,2650U的固件的Board id 为96358VW2
2650BU设备的朋友,没TTL数据线,不要刷哦.呵呵.

还有一点,2650U设备的Flash是8M的,Flash Block是64K的...而国内的2650BU是16M的Flash和Flash Block是128K的... ...
hotqj 发表于 2009-4-8 13:54

期待版主们试试，然后出个教程什么的就好了

cmcgcf08

有网友在已刷9113的2650BU的基础上升级成功.

天涯

等下我就刷进去,试用后再回贴

MINE

已经有人刷挂了。

cmcgcf08

建议没条件的还是不要刷先.

wxhnrb

看看，有人成功了吗？

mzdeng

有刷新成功的，但貌似不能连接。。可能是线路不同

CLS

看了下usermanual，还是不支持usb存储，和9113没啥区别，不激动

天涯

刷上了,启动信息好下:
接了个256M的FAT32格式的U盘,但不知道如何访问这个U盘.请高手解答.谢谢

1. 
   
2. CFE version 1.0.37-10.1 for BCM96358 (32bit,SP,BE)
   
3. Build Date: Tue Apr 24 15:57:24 CST 2007 (gavin@FD5)
   
4. Copyright (C) 2000-2006 Broadcom Corporation.
   
5. 
   
6. Boot Address 0xbe000000
   
7. 
   
8. Initializing Arena.
   
9. Initializing Devices.
   
10. Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
    
11. CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
    
12. CPU running TP0
    
13. Total memory: 67108864 bytes (64MB)
    
14. 
    
15. Total memory used by CFE:  0x80401000 - 0x80527C50 (1207376)
    
16. Initialized Data:          0x8041D580 - 0x8041F480 (7936)
    
17. BSS Area:                  0x8041F480 - 0x80425C50 (26576)
    
18. Local Heap: `              0x80425C50 - 0x80525C50 (1048576)
    
19. Stack Area:                0x80525C50 - 0x80527C50 (8192)
    
20. Text (code) segment:       0x80401000 - 0x8041D57C (116092)
    
21. Boot area (physical):      0x00528000 - 0x00568000
    
22. Relocation 芶ctor:         I:00000000 - D:00000000
    
23. 
    
24. Board IP address                  : 192.168.1.1:ffffff00  
    
25. Host IP address                   : 192.168.1.100  
    
26. Gateway IP address                :   
    
27. Run from flash/host (f/h)         : f  
    
28. Default host run file name        : vmlinux  
    
29. Default host flash file name      : bcm963xx_fs_kernel  
    
30. Boot delay (0-9 seconds)          : 2  
    
31. Board Id (0-8)                    : 96358VW2  
    
32. Number of MAC Addresses (1-32)    : 11  
    
33. Base MAC Address                  : 00:74:04:e4:15:8e  
    
34. PSI 觟ze (1-64) KBytes            : 64  
    
35. Main Thread Number [0|1]          : 0  
    
36. 
    
37. *** Pre髎 any key to stop auto run (2 seconds) ***
    
38. Auto run second count down: 0
    
39. Booting from only image (0xbe800000) ...
    
40. Code Address: 0x80010000, Entry Address: 0x80216018
    
41. Decompression OK!
    
42. Entry at 0x80216018
    
43. Closing network.
    
44. Starting program at 0x80216018
    
45. Linux version 2.6.8.1 (joan@mochow) (gcc version 3.4.2) #1 Tue Mar`31 15:20:17 CS?2009
    
46. Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
    
47. 96358VW2 prom init
    
48. CPU revision is: 0002a010
    
49. Determined physical RAM map:
    
50. memory: 03fa0000 @ 00000000 (usable)
    
51. On node 0 totalpages: 16288
    
52.   DMA zone: 40y6 pages, LIFO batch:1
    
53.   Normal zone: 12192 pages, LIFO batch:2
    
54.   HighMem zone: 0 pages, LIFO batch:1
    
55. Built 1 zonelists
    
56. Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
    
57. brcm mips: enabling icache and dcaghe...
    
58. Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
    
59. Primary data cache 16kB 2-way, linesize 16 bytes.
    
60. PID hash table entries: 256 (order 8: 2048 bytes)
    
61. Using 150.000 MHz high precision 鬷m錼.
    
62. Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
    
63. Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
    
64. Memory: 62124k/65152k available (1783k kernel code, 2960k reserved, 284k data, 76k init, 0k highmem)
    
65. Calibrating delay loop.n. 299.00 BogoMIPS
    
66. Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    
67. Checking for 'wait' instruction...  unavailable.
    
68. NET: Registered protoc飈 family 16
    
69. Total Flash size: 16384K with 128 sectors
    
70. File system address: 0xbe800100
    
71. Can't analyze prologue code at 801cc474
    
72. SCSI subsystem initialized
    
73. usbcore: registered new driver hub
    
74. Initializing Cryptographic API
    
75. PPP generic driver version 2.4.2
    
76. PPP Deflate Compression module registered
    
77. PPP BSD Compression module registered
    
78. MPPE/MPPC encryption/compression module registered
    
79. NET: Registered protocol family 24
    
80. bc?63xx_mtd driver v1.0
    
81. PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
    
82. ehci_hcd 0000:00:0a.0: EHCI Host Controller
    
83. PCI: Setting latency timer of device 0000:00:0a.0 to 64
    
84. ehci_鑓d 0000:00:0a.0: irq 18l pci mem c0000300
    
85. ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
    
86. PCI: cache line size of 32 is not supported by device 0000:00:0a.0
    
87. ehci_hcd 0000:00:0a.0: USB f.f enable? EHCI 1.00, driver 2004-May-10
    
88. hub 1-0:1.0: USB hub found
    
89. hub 1-0:1.0: 2 ports detected
    
90. ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
    
91. ohci_hcd: block sizes: ed 64 td 64
    
92. PCI: Enabling device 0000:00:09.p (0000 -> 0002)
    
93. ohci_hcd 0000:00:09.0: OHCI Host Controller
    
94. PCI: Setting latency timer of device 0000:00:09.0 to 64
    
95. ohci_hcd 0000:00:09.0: irq 13, pci mem ?002400
    
96. ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
    
97. hub 2-0:1.0: USB hub found
    
98. hub 2-0:1.0: 2 ports det錭ted
    
99. usbcore: registered new driver usblp
    
100. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
     
101. Initializing USB Mass Storage driver...
     
102. usbcore: registered new driv錼 usb-storage
     
103. USB Mass Storage support registered.
     
104. brcmboard: brcm_board_init entry
     
105. SES: Button Interrupt 0x3 is enabled
     
106. 
     
107. ======= GPIO CONFIG_BCM96358 init ========
     
108. Serial: BCM63XX driver $Revision: 3.00 $
     
109. ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
     
110. ttyS1 at MMIO 0xff鎒0120 (irq = 11) is a BCM63XX
     
111. NET: Registered protocol family 2
     
112. IP: routing cache hash table of 512 buckets, 4Kbytes
     
113. TCP: Hash tables configured (established`4096 bind x192)
     
114. Init閍lizing IPsec netlink socket
     
115. NET: Registered protocol family 1
     
116. NET: Registered protocol family 17
     
117. NET: Registered protocol family 15
     
118. Ebtables v2.0 registered
     
119. NET: Registered protocol family 8
     
120. NET: Registered protocol family 20
     
121. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
122. All bugs added by David S. Miller <davem@redhat.com>
     
123. VFS: Mounted root (squashfs filesystem) readonly.
     
124. Freeing unused kernel memory: 76k freed
     
125. init started:  BusyBox v1.00 (2009.03.31-07:26+0000) multi-鉧ll binary
     
126. Algorithmics/MIPS FPU Emulator v1.5
     
127. 
     
128. 
     
129. BusyBox v1.00 (2009.03.31-07:26+0000) Built-in shell (msh)
     
130. Enter 'help' for a list of built-in commands.
     
131. 
     
132. 
     
133. Loading drivers and kernel modules...
     
134. 
     
135. atmapi: mod}le license 'Proprietary' taints kernel.
     
136. adsl: adsl_init entry
     
137. blaadd: blaa_detect entry
     
138. Broadcom BCMPROC芐 v1.0 initialized
     
139. Broadcom BCM6358A1 Ethernet Network Device ?.3 Mar 31 2009 15:18:26
     
140. Config Ethernet Switch Through MDIO Pseudo PHY Interface
     
141. dgasp: kerSysRegyste駾yingGasp萢ndler: eth0 registered
     
142. eth0: MAC Address: 00:74:04:E4:15:8E
     
143. Broadcom BCM6358A1 USB Network Device v0.4 Mar 31 2009 15:18:28
     
144. usb0: MAC Address: 00 74 04 E4 15 8F
     
145. usb0: Host MAC Address: 00 74 04 E4 15 90
     
146. PCI: Setting latency timer of device 0000:00:01.0 to 64
     
147. PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
     
148. wl: srom not de篹cted, using main memory mapped srom info (wombo board)
     
149. wl0: wlc_attach: use mac addr from the system pool by id: px776c0000
     
150. wl0: MAC Addre髎: 00:74:04:E4:15:91
     
151. wl0: Broadcom BCM4318 802.11 Wireless Controller 4.100.27.0.cpe2.1
     
152. dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
     
153. usb 2-1: new full speed USB device using address 2
     
154. usb 2-1: not running at`top speed; connect to a high speed hub
     
155. scsi0 : SCSI emulation for USB Mass Storage devices
     
156.   Vendor: Dreams    Model: Flash Disk        Rev: 2.00
     
157.   Type:   Direct-Access                      ANSI SCSI revision: 02
     
158. sda: Unit Not Ready, sense:
     
159. Current : sense = 70  6
     
160. ASC=28 ASCQ= 0
     
161. Raw sense data:0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00
     
162. eth0 Link UP.
     
163. sda : READ CAPACITY failed.
     
164. sda : status=1, message=00, host=0, driver=08
     
165. Current sd: sense = 70  6
     
166. ASC=28 ASCQ= 0
     
167. Raw sense dataz0x70 0x00 0x06 0x00 0x00 0x00 0x00 0x0a 0x00 0x00 0x00 0x00 0x28 0x00 0x00 0x00 0x00 0x00
     
168. sda: assuming Write Enabled
     
169. sda: assuming drive cache: write through
     
170. sda: sda4
     
171. Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
     
172. USB Mass Storage device found at 2
     
173. is not de鎍ult cfg.
     
174. is not default cfg.
     
175. BcmAdsl_Initialize=0xC006A3C8, g_pFnNotifyCallback=0xC0083324
     
176. AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
     
177. pSdramPHY=0xA3FFFFF8, 0x20 0x8088C0
     
178. AdslCoreHwReset: AdslOemDataAddr = 0xA3FFB1E4
     
179. AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 ads?=0x0000p000
     
180. dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
     
181. ATM proc init !!!
     
182. ip_tables: (C) 2000-2002 Netfilter core team
     
183. ip_conntrack version 2.1 (509 buckets, 0 max) - 376 bytes per conntrack
     
184. ip_conntrack_pptp version 2.1 loaded
     
185. ip_nat_pptp version 2.0 loaded
     
186. ip_ct_h323: init success
     
187. ip_nat_h323: init success
     
188. ip_conntrack_rtsp v0.01 l颽ding
     
189. ADSL G.994 training
     
190. ip_nat_rtsp v0.01 loading
     
191. 
     
192. ==>   Bcm963xx Software Version: RU_1.11   <==
     
193. 
     
194. device usb0 entered promiscuous mode
     
195. br0: port 1(usb0) entering learning state
     
196. br0: topology change detected, propagating
     
197. br0: port 1(usb0) entering forwarding sta鬳
     
198. device eth0 entered promiscuous mode
     
199. br0: port 2(eth0) entering learning state
     
200. br0: port 2(eth0) entering forwarding state
     
201. ADSL G.992 started
     
202. Setting SSID "Dlink-2650BU"
     
203. SIOCG蒄FLAGS: No such device
     
204. Setting country code using abbreviation: "CN"
     
205. ADSL G.992 channel analysis
     
206. wlctl: Not Found
     
207. channel 1 selected
     
208. wl0: current channel 1
     
209. device wl0 entered promiscuous mode
     
210. br0: port 3(wl0) entering learning state
     
211. br0: topology change detected, propagating
     
212. br0: port 3(wl0) entering forwarding state
     
213. ADSL G.992 message exchange
     
214. ADSL link up, fast, us}672, ds=4928
     
215. BcmRfc2684_init interface is not up nas_0_0_35!
     
216. pvc2684ctl -a -v 0.0.35 &
     
217. pvc2684d: Interface "nas_0_0_35" created sucessfully
     
218. 
     
219. pvc2684d: 胦mmunicating ov錼 ATM 0.0.35, encapsulation: LLC
     
220. 
     
221. 
     
222. +++steven: in frontend.c:main:13
     
223. argv[0] = dhcpd
     
224. argv[1] = (null)
     
225. 
     
226. k++steven: in dhcpd.c:udhcpd:188
     
227. device usb0 left promiscuous mode
     
228. br0: p飏t 1(usb0) entering 鋓sabled state
     
229. device eth0 left promiscuous mode
     
230. br0: port 2(eth0) entering disabled state
     
231. device wl0 left promiscuous mode
     
232. br0: port 3(wl0) entering disabled state
     
233. device usb0 entered promiscuous mode
     
234. br0: port 1(usb0) entering learning state
     
235. br0: topology change de鬳ct錮, propagat閚g
     
236. 鈘0:`port 1(u骲0) entering forwarding state
     
237. device eth0 entered promiscuous mode
     
238. br0: port 2(eth0) entering learning state
     
239. br0: topology change detected, propagating
     
240. br0: port 2(eth0) entering forwarding state
     
241. device wl0 entered promiscuous mode
     
242. br0: port 3(wl0) entering learning state
     
243. br0: topology chang?detected, propagating
     
244. br0: port 3(wl0) entering forwarding state
     
245. 
     
246. ioctl, p_name=diapd
     
247. I am open &async_queue = 0xc004a584<3>kill_fasync: bad magic number in fasync_struct!
     
248. wlButtonInit open success
     
249. gpio_fasync
     
250. Pasync_駏eue->magic = 0x4601
     
251. 
     
252. *** diap  wait system init 1 sec start
     
253. 
     
254. ##############status LED blink now##################
     
255. br0: port 1(usb0) entering disabled state
     
256. 
     
257. *** diap  wait system init 1 sec end
     
258. dft, wanIpAddress = , wanSubnetMask =
     
259. vpi = 0, vci = 35, conId = 1, portId = 0
     
260. nat = 1, firewall = 1
     
261. tr69c: start with default interface nas_0_0_35
     
262. Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=61.191.56.117 DST=219.159.102.16 LEN=40 TOS=0x00 PREC=0x00 TTL=112 ID=256 P襉TO=TCP SPT=6000 DPT=135 WINDOW=16384 RES=0x00 SYN URGP=0
     
263. Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=203.171.237.237 DST=219.159.102.16 LEN=40 TOS=0x00 PREC=0x00 TTL=111 ID=256 PROTO=TCP SPT=6000 DPT=1433 WINDOW=16384 RES=0x00 SYN URGP=0
     
264. Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 D覶=219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=22661 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=65535 RES=0x00 SYN URGP=0
     
265. Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 DS?219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=23448 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=65535 RES=0x00 SYN URGP=0
     
266. Intrusion -> IN=nas_0_0_35 OUT= MAC=00:74:04:e4:15:92:00:18:82:1c:c6:95:08:00 SRC=121.35.0.83 DST=219.159.102.16 LEN=48 TOS=0x00 PREC=0x00 TTL=119 ID=24689 DF PROTO=TCP SPT=1105 DPT=4782 WINDOW=v5535 RES=0xp0 SYN URGP=0
     

复制代码

天涯

界面如下图