|
|
故障为路由反复重启 进入不了设置界面
启动过程
Basic POST completed... Success.
Last reset cause: Software reset (memory controller also reset)
ZXV10 HomeGateway bootloader version: 1.4.4.3
Board hardware version: 2.0.6
Flash size: 16M
Memory size: 32M
(c) Copyright 2004-2007 ZTE CORPORATION. All Rights Reserved.
Press ESC for monitor...
ZXV10 HGW>
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2003 Texas Instruments Incorporated; Copyright (C) 1999-2003 Igor
Pavlov.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,115200
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
CONFIG_AVALANCHE_VLYNQ_POLARITY_LOW
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.6.17_mvl21-malta-mips_fp_le ([email=xia@XLVersion]xia@XLVersion[/email]) (gcc version 2.96 20
000731 (Red Hat Linux 7.3 2.96-113.2) neon) #1 Wed Apr 2 17:25:39 CST 2008
Set GPIO19 interrupt mode now:
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 01fe0000 @ 14020000 (usable)
On node 0 totalpages: 8192
zone(0): 8192 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line: BOOTCFG_A 11001100 0 1 8 9
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 29788k/32768k available (1880k kernel code, 2980k reserved, 199k data, 6
8k init)
Dentry-cache hash table entries: 4096 (order: 3, 32768 bytes)
Inode-cache hash table entries: 2048 (order: 2, 16384 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 8192 (order: 3, 32768 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.6
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
JFFS2 version 2.1. (C) 2001, 2002 Red Hat, Inc., designed by Axis Communications
AB.
ticfg_name_select : board_hwversion ==0
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
cpmac_dev_probe : WAN MODE == adsl
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
cpmac_dev_init,EnableHwIGMP1
addr=0x000c value=0x8038
addr=0x000b value=0x8001
addr=0x000b value=0xa001
Default Asymmetric MTU for eth0 1500
Default Asymmetric MTU for eth1 1500
CPMAC: Registered switch port 1 with device eth1
Default Asymmetric MTU for eth2 1500
CPMAC: Registered switch port 2 with device eth2
Default Asymmetric MTU for eth3 1500
CPMAC: Registered switch port 3 with device eth3
Default Asymmetric MTU for eth4 1500
CPMAC: Registered switch port 4 with device eth4
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
cpmac_dev_probe : sync @ normal
PPP generic driver version 2.4.1
avalanche flash device: 0x1000000 at 0x10000000.
Found: Spansion S29GL128N02
Physically mapped flash:0: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
cfi_amdstd_setup :: Using buffer write method --- in w300
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0x160000), with size (0x400000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00160000-0x00560000 : "mtd0"
Avalanche: linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x80000), with size (0xe0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00080000-0x00160000 : "mtd1"
Avalanche: linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00020000 : "mtd2"
Avalanche: linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x20000), with size (0x40000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00060000 : "mtd3"
Avalanche: linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x80000), with size (0x4e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00080000-0x00560000 : "mtd4"
Avalanche: linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
Avalanche: Adding a mtd5 image (0x60000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00060000-0x00080000 : "mtd5"
Avalanche: linking partition mtd5: mtd5 -> ../../mtdblock/5
Looking for mtd device :mtd6:
Avalanche: Adding a mtd6 image (0x560000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00560000-0x00580000 : "mtd6"
Avalanche: linking partition mtd6: mtd6 -> ../../mtdblock/6
Looking for mtd device :mtd7:
Avalanche: Adding a mtd7 image (0xb00000), with size (0x500000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00b00000-0x01000000 : "mtd7"
Avalanche: linking partition mtd7: mtd7 -> ../../mtdblock/7
Looking for mtd device :mtd8:
Avalanche: Adding a mtd8 image (0x6e0000), with size (0x400000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x006e0000-0x00ae0000 : "mtd8"
Avalanche: linking partition mtd8: mtd8 -> ../../mtdblock/8
Looking for mtd device :mtd9:
Avalanche: Adding a mtd9 image (0x600000), with size (0xe0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00600000-0x006e0000 : "mtd9"
Avalanche: linking partition mtd9: mtd9 -> ../../mtdblock/9
Looking for mtd device :mtd10:
Avalanche: Adding a mtd10 image (0x580000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00580000-0x005a0000 : "mtd10"
Avalanche: linking partition mtd10: mtd10 -> ../../mtdblock/10
Looking for mtd device :mtd11:
Avalanche: Adding a mtd11 image (0x5a0000), with size (0x40000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x005a0000-0x005e0000 : "mtd11"
Avalanche: linking partition mtd11: mtd11 -> ../../mtdblock/11
Looking for mtd device :mtd12:
Avalanche: Adding a mtd12 image (0x600000), with size (0x4e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00600000-0x00ae0000 : "mtd12"
Avalanche: linking partition mtd12: mtd12 -> ../../mtdblock/12
Looking for mtd device :mtd13:
Avalanche: Adding a mtd13 image (0x5e0000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x005e0000-0x00600000 : "mtd13"
Avalanche: linking partition mtd13: mtd13 -> ../../mtdblock/13
Looking for mtd device :mtd14:
Avalanche: Adding a mtd14 image (0xae0000), with size (0x20000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00ae0000-0x00b00000 : "mtd14"
Avalanche: linking partition mtd14: mtd14 -> ../../mtdblock/14
Looking for mtd device :mtd15:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 2048)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (256 buckets, 2048 max) - 372 bytes per conntrack
ip_ct_sip: registering helper for port 5060
ip_ct_sip: registering helper for port 5063
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
bzp : /dev/mtdblock0
FAT: bogus logical sector size 22528
!!!!root fs is squash fs, so skip jffs2 fs
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 68k freed
serial console detected. Disabling virtual terminals.
console=/dev/tts/0
init started: BusyBox v0.61.pre (2008.04.02-09:36+0000) multi-call binary
Starting pid 10, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
mnum== e0011985
JFFS is already here!
mount -t jffs2 /dev/mtdblock/7 /usr/local/ct
cd: can't cd to mod
ledcfg: reading Standard Configuration File /etc/led.conf
ledcfg: configured 19 states
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DSL_FEATURE_CNTL_0 (_dsl_Feature_0) = 4000
DSL_PHY_CNTL_0 (_dsl_PhyControl_0) = 200
DSP binary filesize = 383830 bytes
^[tn7dsl_init : env var DSL_BIT_TMODE is set
tn7dsl_set_modulation : Setting mode to 0xff
Texas Instruments ATM driver: version:[7.02.01.00]
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
SCSI subsystem driver Revision: 1.00
^[Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
USB Mass Storage support registered.
ISP116x Chip_id = 6123
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 2 ports detected
ISP116x_HCD Initialization Successful
Waiting for enter to start '/bin/sh' (pid 58, terminal /dev/tts/0)
Please press Enter to activate this console. ****** unusedenv has been clean****
**
Starting pid 58, console /dev/tts/0: '/bin/sh'
BusyBox v0.61.pre (2008.04.02-09:36+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
# $$$$$$$proc_newboot_defparams
UP MOde is adsl
==== In logic main ====
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
ADSL default config is already here!
iptables: No chain/target/match by that name
Logger:log_load_from_flash:will load log from flash
Logger:log_load_from_flash:load access file success,buf:0x100308d0,40741 byte
Logger:log_load_from_flash:finshed to parse log
Logger:log_load_from_flash:will load log from flash
Logger:log_load_from_flash:load security file success,buf:0x100463d0,10620 byte
Logger:log_load_from_flash:finshed to parse log
Tr069ConnectionChanged():Restart tr069 listen socket (mini_httpd) , iface=
name MappingEntity
set_pval: No key in list InternetGatewayDevice.ManagementServer.URL
set_pval: No key in list InternetGatewayDevice.ManagementServer.URL
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_MiddlewareMgt
.MiddlewareURL
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_MiddlewareMgt
.MiddlewareURL
set_pval: No key in list InternetGatewayDevice.ManagementServer.CTMgtIPAddress
set_pval: No key in list InternetGatewayDevice.ManagementServer.CTMgtIPAddress
set_pval: No key in list InternetGatewayDevice.ManagementServer.CTUserIPAddress1
set_pval: No key in list InternetGatewayDevice.ManagementServer.MgtDNS
set_pval: No key in list InternetGatewayDevice.ManagementServer.MgtDNS
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_MiddlewareMgt
.InternetPvc
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_MiddlewareMgt
.InternetPvc
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_TeleComAccoun
t.TeleAccountChange
set_pval: No key in list InternetGatewayDevice.DeviceInfo.X_CT-COM_TeleComAccoun
t.TeleAccountChange
@@@@@@ delete_CRURL_from_notification:
ACTV_NOTIFY_DUMP
List:
add_middle_to_notification(): initialize notify parameters list. 2.
List: 'InternetGatewayDevice.ManagementServer.URL'='http://devacs.edatahome.com:
9090/ACS-server/ACS/', 'InternetGatewayDevice.DeviceInfo.X_CT-COM_MiddlewareMgt.
MiddlewareURL'='0.0.0.0:9080', 'InternetGatewayDevice.ManagementServer.CTMgtIPAd
dress'='N/A', 'InternetGatewayDevice.ManagementServer.CTUserIPAddress1'='N/A', '
InternetGatewayDevice.ManagementServer.MgtDNS'='N/A', 'InternetGatewayDevice.Dev
iceInfo.X_CT-COM_MiddlewareMgt.InternetPvc'='N/A', 'InternetGatewayDevice.Device
Info.X_CT-COM_TeleComAccount.TeleAccountChange'='0',
MWSURL: 0.0.0.0
==>set_tr069_url_conf strValue = http://devacs.edatahome.com:9090/ACS-server/AC
S/
0000-00-00T00:00:11 [Notice] dev_init one time
iptables: Bad rule (does a matching rule exist in that chain?)
restoretelnetuserpass restore user/pass ok user is root,pass is root
security init E8-B version get password1
resolver: configuration tree:
0000-00-00T00:00:16 [Critical] oamPingInterval(20)(20)
********Get pmodulation of 0xff from env********
0000-00-00T00:00:17 [Notice] ssid0 PSK value : drbegr6c. len : 8
Eeeeeeeenabe SC and akmp
#######WSC isactive = 1
0000-00-00T00:00:18 [Notice] MAC address : 00:19:c6:af:24:3a
0000-00-00T00:00:19 [Notice] Read WLAN_CARD_TYPE error!!!!! default to 200
ap is loading,set ap to busy
0000-00-00T00:00:19 [Notice] AP Acquiring Lock
0000-00-00T00:00:22 [Notice] ppp_led_ctl !DO! LED =0
0000-00-00T00:00:22 [Notice] Valid Configuration Tree
Got module id = landhcps0
Got module id = landhcps0
Got module id = landhcps0
Got module id = landhcps0
Got module id = landhcps0
0000-00-00T00:00:24 [Notice] stat successfull for /etc/resolv.conf.
in pr_start_bindroute, bridge connection here
in pr_start_bindroute, bridge connection here
in pr_start_bindroute, bridge connection here
0000-00-00T00:00:25 [Critical] NTP Polling Timer for DHCP Started succesfully.
rm: cannot remove `/var/tmp/pap-secrets': No such file or directory
###(init_pppproxy_link) num= 0
0000-00-00T00:00:25 [Notice] DSL Polling Timer Started succesfully.
0000-00-00T00:00:25 [Error] &&ð_start
0000-00-00T00:00:25 [Error] &&ð_start, ifconfig
0000-00-00T00:00:26 [Error] &&ð_start
0000-00-00T00:00:26 [Error] &&ð_start
0000-00-00T00:00:26 [Error] &&ð_start
0000-00-00T00:00:27 [Notice] Firewall NAT service started
0000-00-00T00:00:27 [Notice] ppp_proxy pEnable=-1!
0000-00-00T00:00:27 [Alert] 104001 The device rebooted by software reset
0000-00-00T00:00:28 [Notice] AP REPORT LOCK ACQUIRED
0000-00-00T00:00:28 [Notice] wlan_handle_load_event - Acquired Lock
0000-00-00T00:00:28 [Notice] ssid0 PSK value : drbegr6c. len : 8
Eeeeeeeenabe SC and akmp
#######WSC isactive = 1
0000-00-00T00:00:28 [Notice] MAC address : 00:19:c6:af:24:3a
0000-00-00T00:00:28 [Notice] Read WLAN_CARD_TYPE error!!!!! default to 200
0000-00-00T00:00:29 [Error] del_iptable_rules : ppp_name not intact
0000-00-00T00:00:29 [Warning] bogus logical sector size 22528
0000-00-00T00:00:29 [Warning] !!!!root fs is squash fs, so skip jffs2 fs
0000-00-00T00:00:29 [Warning] Mounted root (squashfs filesystem) readonly.
0000-00-00T00:00:29 [Warning] Mounted devfs on /dev
0000-00-00T00:00:29 [Warning] 68k freed
0000-00-00T00:00:29 [Warning] Algorithmics/MIPS FPU Emulator v1.5
0000-00-00T00:00:29 [Warning] registered device TI Avalanche SAR
0000-00-00T00:00:29 [Warning] Ohio250(7200/7100A2) detected
0000-00-00T00:00:29 [Warning] DSL_FEATURE_CNTL_0 (_dsl_Feature_0) = 4000
0000-00-00T00:00:29 [Warning] DSL_PHY_CNTL_0 (_dsl_PhyControl_0) = 200
0000-00-00T00:00:29 [Warning] DSP binary filesize = 383830 bytes
0000-00-00T00:00:29 [Warning] env var DSL_BIT_TMODE is set
0000-00-00T00:00:29 [Warning] Setting mode to 0xff
0000-00-00T00:00:29 [Warning] version:[7.02.01.00]
0000-00-00T00:00:29 [Warning] ISP116x Chip_id = 6123
0000-00-00T00:00:29 [Warning] ISP116x_HCD Initialization Successful
0000-00-00T00:00:29 [Warning] Default Asymmetric MTU for br0 1500
!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
Core Logic received 'SEGFAULT' signal, halting and reboot now...
!!!!!!!!!!!!!!!!Restarting system.
!!!!!!!!!!!!!!!!read flash area ...... 9000 4080
!!!!!!!!!!!!!!!!flash status 0 |
|
粤公网安备44152102000001号 
发表于 2009-2-25 20:20:52
发表于 2009-2-25 22:55:26
发表于 2009-2-26 11:29:07
