求助:db120-gw 问题

天涯

实践证明,楼上的 HOTQJ朋友讲的正确.右上角的是TTL接口.下偏左的空5针孔,目前偶也不知道.刚做了根TTL数据线,启动信息尽收眼底,可有一个问题,就是按键无法暂停启动过程.也就进不了CFE工菜单.我的数据线是以前买的NOKIA 6100时的手机线改造的. 之前用此数据把实达的一个老猫救活过来.

1. 
   
2. 
   
3. CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
   
4. Build Date: 二  1月 29 07:41:15 CST 2008 (root@ZTJ)
   
5. Copyright (C) 2000-2006 Broadcom Corporation.
   
6. 
   
7. Boot Address 0xbe000000
   
8. 
   
9. Initializing Arena.
   
10. Initializing Devices.
    
11. Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
    
12. Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
    
13.               AuxFS[95,0xbebe0000] Misc[126,0xbefc0000] PSI[127,0xbefe0000]
    
14. Flash RootFS Partition Length: 12320768
    
15. Auto-negotiation timed-out
    
16. 10 MB Half-Duplex (assumed)
    
17. CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
    
18. CPU running TP0
    
19. Total memory: 33554432 bytes (32MB)
    
20. 
    
21. Total memory used by CFE:  0x80401000 - 0x805285A0 (1209760)
    
22. Initialized Data:          0x8041DD30 - 0x8041FDC0 (8336)
    
23. BSS Area:                  0x8041FDC0 - 0x804265A0 (26592)
    
24. Local Heap:                0x804265A0 - 0x805265A0 (1048576)
    
25. Stack Area:                0x805265A0 - 0x805285A0 (8192)
    
26. Text (code) segment:       0x80401000 - 0x8041DD30 (118064)
    
27. Boot area (physical):      0x00529000 - 0x00569000
    
28. Relocation Factor:         I:00000000 - D:00000000
    
29. 
    
30. Board IP address                  : 192.168.1.1:ffffff00
    
31. Host IP address                   : 192.168.1.159
    
32. Gateway IP address                :
    
33. Run from flash/host (f/h)         : h
    
34. Default host run file name        : 308nfs6358
    
35. Default host flash file name      : bcm963xx_fs_kernel
    
36. Boot delay (0-9 seconds)          : 1
    
37. Board Id (0-9)                    : 96358VW2
    
38. Number of MAC Addresses (1-32)    : 24
    
39. Base MAC Address                  : 00:1e:40:31:37:86
    
40. PSI Size (1-64) KBytes            : 24
    
41. Flash Block Size (1-128) in KBytes: 128
    
42. Auxillary File System Size Percent: 25
    
43. Main Thread Number [0|1]          : 0
    
44. 
    
45. *** Press any key to stop auto run (1 seconds) ***
    
46. Auto run second count down: 0
    
47. Booting from only image (0xbe020000) ...
    
48. Code Address: 0x80010000, Entry Address: 0x80259018
    
49. Decompression OK!
    
50. Entry at 0x80259018
    
51. Closing network.
    
52. Starting program at 0x80259018
    
53. Linux version 2.6.8.1 (root@dhcppc2) (gcc version 3.4.2) #1 Sun Jul 6 20:09:15 E
    
54. DT 2008
    
55. Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
    
56. Not find second flash
    
57. 96358VW2 prom init
    
58. CPU revision is: 0002a010
    
59. Determined physical RAM map:
    
60. memory: 01fa0000 @ 00000000 (usable)
    
61. On node 0 totalpages: 8096
    
62.   DMA zone: 4096 pages, LIFO batch:1
    
63.   Normal zone: 4000 pages, LIFO batch:1
    
64.   HighMem zone: 0 pages, LIFO batch:1
    
65. Built 1 zonelists
    
66. Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
    
67. brcm mips: enabling icache and dcache...
    
68. Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
    
69. Primary data cache 16kB 2-way, linesize 16 bytes.
    
70. PID hash table entries: 128 (order 7: 1024 bytes)
    
71. Using 150.000 MHz high precision timer.
    
72. Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
    
73. Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
    
74. Memory: 29420k/32384k available (1909k kernel code, 2920k reserved, 426k data, 7
    
75. 6k init, 0k highmem)
    
76. Calibrating delay loop... 299.00 BogoMIPS
    
77. Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
    
78. Checking for 'wait' instruction...  unavailable.
    
79. NET: Registered protocol family 16
    
80. Computing partition layout for flash of size[16777216] sectors[128]
    
81. Flash split 25% into RootFS+Kernel[12320768] : AuxFS[4063232]
    
82. Partition ROOTFS_KRN [0xbe020000,   12320768] Blks[ 94:   1 ..  94]
    
83. SubPartition Image 1 [0xbe020000,    6160384] Blks[ 47:   1 ..  47]
    
84. SubPartition Image 2 [0xbe600000,    6160384] Blks[ 47:  48 ..  94]
    
85. Blk# BlkOff Blks BlkSize AvailSize   MemStart     MemLen Partition Name
    
86.    0   1408    1  131072    131072 0xbe000580       1024 BOOTLOADER
    
87.    1      0   94  131072  12320768 0xbe020000   12320768 ROOTFS_KRN
    
88.   95      0   31  131072   4063232 0xbebe0000    4063232 JFFS_AUXFS
    
89. 126 106496    1  131072    131072 0xbefda000      24576 PERSISTMEM 2
    
90. 127      0    1  131072    131072 0xbefe0000     106496 LOG_SCRPAD
    
91. 127 106496    1  131072    131072 0xbeffa000      24576 PERSISTMEM
    
92. Blk# BlkOff Blks  MemLen Partition Name
    
93.    0   1408    1    1024 NVRAM
    
94. 126 106496    1   24576 Config 2
    
95. 127      0    1   98304 Log
    
96. 127  98304    1    8192 Scratch PAD
    
97. 127 106496    1   24576 Config 1
    
98. Can't analyze prologue code at 801ebe04
    
99. SCSI subsystem initialized
    
100. usbcore: registered new driver hub
     
101. JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
     
102. Initializing Cryptographic API
     
103. PPP generic driver version 2.4.2
     
104. NET: Registered protocol family 24
     
105. Using noop io scheduler
     
106. bcm963xx_mtd driver v2.0
     
107. File system address: 0xbe020100
     
108. Registered device mtd[BCM63XX RootFS] dev[0] Flash[0xbe020100,3477504]
     
109. Registered device mtd[BCM63XX AuxFS] dev[1] Flash[0xbebe0000,4063232]
     
110. PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
     
111. ehci_hcd 0000:00:0a.0: EHCI Host Controller
     
112. PCI: Setting latency timer of device 0000:00:0a.0 to 64
     
113. ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
     
114. ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
     
115. PCI: cache line size of 32 is not supported by device 0000:00:0a.0
     
116. ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
     
117. hub 1-0:1.0: USB hub found
     
118. hub 1-0:1.0: 2 ports detected
     
119. ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
     
120. ohci_hcd: block sizes: ed 64 td 64
     
121. PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
     
122. ohci_hcd 0000:00:09.0: OHCI Host Controller
     
123. PCI: Setting latency timer of device 0000:00:09.0 to 64
     
124. ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
     
125. ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
     
126. hub 2-0:1.0: USB hub found
     
127. hub 2-0:1.0: 2 ports detected
     
128. usbcore: registered new driver usblp
     
129. drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
     
130. Initializing USB Mass Storage driver...
     
131. usbcore: registered new driver usb-storage
     
132. USB Mass Storage support registered.
     
133. brcmboard: brcm_board_init entry
     
134. SES: Button Interrupt 0x3 is enabled
     
135. SES: LED GPIO 0x801b is enabled
     
136. Serial: BCM63XX driver $Revision: 3.00 $
     
137. ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
     
138. ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
     
139. u32 classifier
     
140. NET: Registered protocol family 2
     
141. IP: routing cache hash table of 512 buckets, 4Kbytes
     
142. TCP: Hash tables configured (established 2048 bind 4096)
     
143. Initializing IPsec netlink socket
     
144. NET: Registered protocol family 1
     
145. NET: Registered protocol family 17
     
146. NET: Registered protocol family 15
     
147. Ebtables v2.0 registered
     
148. NET: Registered protocol family 8
     
149. NET: Registered protocol family 20
     
150. 802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
     
151. All bugs added by David S. Miller <davem@redhat.com>
     
152. VFS: Mounted root (squashfs filesystem) readonly.
     
153. Freeing unused kernel memory: 76k freed
     
154. init started:  BusyBox v1.00 (2008.07.07-00:16+0000) multi-call binary
     
155. Algorithmics/MIPS FPU Emulator v1.5
     
156. 
     
157. 
     
158. BusyBox v1.00 (2008.07.07-00:16+0000) Built-in shell (msh)
     
159. Enter 'help' for a list of built-in commands.
     
160. 
     
161. 
     
162. Loading drivers and kernel modules...
     
163. 
     
164. atmapi: module license 'Proprietary' taints kernel.
     
165. adsl: adsl_init entry
     
166. blaadd: blaa_detect entry
     
167. Broadcom BCMPROCFS v1.0 initialized
     
168. Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul  6 2008 20:06:35
     
169. Config Internal PHY Through MDIO
     
170. BCM63xx_ENET: Auto-negotiation timed-out
     
171. BCM63xx_ENET: 10 MB Half-Duplex (assumed)
     
172. eth0: MAC Address: 00:1E:40:31:37:86
     
173. Broadcom BCM6358A1 Ethernet Network Device v0.3 Jul  6 2008 20:06:35
     
174. Config Ethernet Switch Through MDIO Pseudo PHY Interface
     
175. dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
     
176. eth1: MAC Address: 00:1E:40:31:37:87
     
177. Broadcom BCM6358A1 USB Network Device v0.4 Jul  6 2008 20:06:38
     
178. usb0: MAC Address: 00 1E 40 31 37 88
     
179. usb0: Host MAC Address: 00 1E 40 31 37 89
     
180. PCI: Setting latency timer of device 0000:00:01.0 to 64
     
181. PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
     
182. wl: srom not detected, using main memory mapped srom info (wombo board)
     
183. wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
     
184. wl0: MAC Address: 00:1E:40:31:37:8A
     
185. wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
     
186. dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
     
187. BcmAdsl_Initialize=0xC00BA3F8, g_pFnNotifyCallback=0xC00D33C4
     
188. AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
     
189. pSdramPHY=0xA1FFFFF8, 0xFFFFFFFF 0xFFFFFFFF
     
190. AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
     
191. AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
     
192. dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
     
193. ATM proc init !!!
     
194. ip_tables: (C) 2000-2002 Netfilter core team
     
195. ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
     
196. ip_conntrack_pptp version 2.1 loaded
     
197. ip_nat_pptp version 2.0 loaded
     
198. ip_ct_h323: init success
     
199. ip_nat_h323: init success
     
200. ip_conntrack_rtsp v0.01 loading
     
201. ip_nat_rtsp v0.01 loading
     
202. 
     
203. ==>   Bcm963xx Software Version: 3.10L.CT_06V.A2pB022g.d20e   <==
     
204. 
     
205. device usb0 entered promiscuous mode
     
206. br0: port 1(usb0) entering learning state
     
207. br0: topology change detected, propagating
     
208. br0: port 1(usb0) entering forwarding state
     
209. device eth0 entered promiscuous mode
     
210. br0: port 2(eth0) entering learning state
     
211. br0: topology change detected, propagating
     
212. br0: port 2(eth0) entering forwarding state
     
213. killall: lld2d: no process killed
     
214. killall: wsccmd: no process killed
     
215. killall: wps_btn: no process killed
     
216. Setting SSID "Dreams-adslG"
     
217. SIOCGIFFLAGS: No such device
     
218. SIOCGIFFLAGS: No such device
     
219. SIOCGIFFLAGS: No such device
     
220. SIOCSIFHWADDR: No such device
     
221. wlctl: wl driver adapter not found
     
222. SIOCSIFHWADDR: No such device
     
223. wlctl: wl driver adapter not found
     
224. SIOCSIFHWADDR: No such device
     
225. wlctl: wl driver adapter not found
     
226. Setting country code using abbreviation: "CN"
     
227. wlctl: Not Found
     
228. wlctl: Not Found
     
229. wlctl: Not Found
     
230. wl0: current channel 11
     
231. device wl0 entered promiscuous mode
     
232. br0: port 3(wl0) entering learning state
     
233. br0: topology change detected, propagating
     
234. br0: port 3(wl0) entering forwarding state
     
235. binding raw socket (index= 9, fd=8) on br0 to TOPO_ETHERTYPE
     
236. lld2d: listening at address: 00:1e:40:31:37:86
     
237. lld2d: Using syslog
     
238. lld2d: Daemonizing...
     
239. lld2d: listening on interface br0
     
240. WlMngr::startWsc: client-pbc mode
     
241. *********************************************
     
242. Wi-Fi Simple Config Application - Intel Corp.
     
243. Version: Build 1.0.5, November 19 2006
     
244. *********************************************
     
245. Initializing stack... OK
     
246. Now starting stack
     
247. get mac = 00 1E 40 31 37 8A
     
248. BcmRfc2684_init interface is not up nas_0_0_35!
     
249. pvc2684ctl -a -v 0.0.35 &
     
250. pvc2684d: Interface "nas_0_0_35" created sucessfully
     
251. 
     
252. pvc2684d: Communicating over ATM 0.0.35, encapsulation: LLC
     
253. 
     
254. HTB init, kernel part version 3.17
     
255. eth1.2: MAC Address: 00:1E:40:31:37:87
     
256. eth1.3: MAC Address: 00:1E:40:31:37:87
     
257. eth1.4: MAC Address: 00:1E:40:31:37:87
     
258. SIOCSIFFLAGS: Network is down
     
259. SIOCSIFFLAGS: Network is down
     
260. SIOCSIFFLAGS: Network is down
     
261. device usb0 left promiscuous mode
     
262. br0: port 1(usb0) entering disabled state
     
263. device eth0 left promiscuous mode
     
264. br0: port 2(eth0) entering disabled state
     
265. device wl0 left promiscuous mode
     
266. br0: port 3(wl0) entering disabled state
     
267. device usb0 entered promiscuous mode
     
268. br2: port 1(usb0) entering learning state
     
269. br2: topology change detected, propagating
     
270. br2: port 1(usb0) entering forwarding state
     
271. device eth0 entered promiscuous mode
     
272. br0: port 1(eth0) entering learning state
     
273. br0: topology change detected, propagating
     
274. br0: port 1(eth0) entering forwarding state
     
275. device wl0 entered promiscuous mode
     
276. br0: port 2(wl0) entering learning state
     
277. br0: topology change detected, propagating
     
278. br0: port 2(wl0) entering forwarding state
     
279. device eth1.2 entered promiscuous mode
     
280. br0: port 3(eth1.2) entering learning state
     
281. br0: topology change detected, propagating
     
282. br0: port 3(eth1.2) entering forwarding state
     
283. device eth1.3 entered promiscuous mode
     
284. br0: port 4(eth1.3) entering learning state
     
285. br0: topology change detected, propagating
     
286. br0: port 4(eth1.3) entering forwarding state
     
287. device eth1.4 entered promiscuous mode
     
288. br0: port 5(eth1.4) entering learning state
     
289. br0: topology change detected, propagating
     
290. br0: port 5(eth1.4) entering forwarding state
     
291. CT SystemLog Init Read From Flash string lenth =12296
     
292. CT SystemLog Init Read From Flash string acsloglenth =5975 secloglenth=343
     
293. nas_del_wsc_ie: no valid ie was saved, len = -1
     
294. 
     
295. ******* MODE: AP with built-in Registrar and UPnP Proxy *******
     
296. WSC: Build-in Regstrar, wait for start command....
     
297. nas_del_wsc_ie: no valid ie was saved, len = -1
     
298. device wl0 is already a member of a bridge; can't enslave it to bridge br0.
     
299. br0: port 1(eth0) entering disabled state
     
300. br0: port 3(eth1.2) entering disabled state
     
301. br0: port 4(eth1.3) entering disabled state
     
302. br0: port 5(eth1.4) entering disabled state
     
303. br2: port 1(usb0) entering disabled state
     

复制代码

[ 本帖最后由 天涯 于 2008-9-2 19:04 编辑 ]

yehaku

看下FW支持那几个主板ID

天涯

我这线不知道是不是驱动不对还是芯片的问题,我按暂停,却停不下来.

还有楼上朋友讲的这个问题,如果能按住暂停,要用什么指令查看.完整的启动信息我已经贴出来了啊.

yehaku

换个超级终端软件看看。我这个TTL也是换了几个才连起的。
对了。如果你能暂停起。进到CFE》状态。先打个HELP就知道了。一般是按B。显示支持的主板ID表。
按P就是现实目前的配制信息。以上是我2650的功能。DB120目前没拿到。无法研究。

[ 本帖最后由 yehaku 于 2008-9-3 01:46 编辑 ]

天涯

已经可以停下来了,等我看到了,再贴出来.

天涯

96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
96358VW2_b20     ------- 9