Minimal POST completed... Success.
Last reset cause: Hardware reset (Power-on reset)
ZXV10 W300 BOOT 1.0 rev: 1.2.5.10
(c) Copyright 2004-2005 ZTE CORPORATION. All Rights Reserved.
Press ESC for monitor... 1
ZXV10 W300>
Booting...
Launching kernel decompressor.
Starting LZMA Uncompression Algorithm.
Copyright (C) 2005 ZTE Corporation.
Compressed file is LZMA format.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 16kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le ([email=root@XLVersion]root@XLVersion[/email]) (gcc version 2.96 20000731 (Red Hat Linux 7.3 2.96-113.2) neon) #2 Wed Oct 25 16:48:17 CST 2006
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 000b71b0(750000)
CPU frequency 150.00 MHz
Calibrating delay loop... 149.91 BogoMIPS
Freeing Adam2 reserved memory [0x14001000,0x0001f000]
Memory: 14380k/16384k available (1487k kernel code, 2004k reserved, 75k data, 60k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction... unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 512
Using 576 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
ttyS01 at 0xa8610f00 (irq = 16) is a 16550A
oyyz_vlynq init
Vlynq CONFIG_MIPS_AVALANCHE_VLYNQ_PORTS=2
Vlynq Device vlynq0 registered with minor no 63 as misc device. Result=0
Vlynq instance:0 Link UP
Vlynq Device vlynq1 registered with minor no 62 as misc device. Result=0
VLYNQ 1 : init failed
switch_connect ok
switchadd ok
switch start
--oyyz config the watch dog
--oyyz enable the watch dog
oyyz_wlan_005
oyyz_wlan_006
block: 64 slots per queue, batch=16
oyyz_ports=1
Cpmac driver is allocating buffer memory at init time.
Cpmac driver Disable TX complete interrupt setting threshold to 20.
Default Asymmetric MTU for eth0 1500
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Found: Fujitsu S29GL032R3
Physically mapped flash:0: Found 1 x16 devices at 0x0 in 16-bit mode
number of JEDEC chips: 1
Looking for mtd device :mtd0:
Found a mtd0 image (0xa0000), with size (0x360000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a0000-0x00400000 : "mtd0"
Looking for mtd device :mtd1:
Found a mtd1 image (0x20000), with size (0x80000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x000a0000 : "mtd1"
Looking for mtd device :mtd2:
Found a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Looking for mtd device :mtd3:
Found a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Looking for mtd device :mtd4:
Found a mtd4 image (0x20000), with size (0x3e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00400000 : "mtd4"
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (128 buckets, 1024 max) - 364 bytes per conntrack
ip_tables: (c)2000 Netfilter core team
netfilter PSD loaded - (c) astaro AG
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
Please set the MAC Address for the WAN Bridge.
Set the Environment variable 'wan_br_mac'.
MAC Address should be in the following format: xx.xx.xx.xx.xx.xx
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 60k freed
serial console detected. Disabling virtual terminals.
console=/dev/tts/0
init started: BusyBox v0.61.pre (2006.10.25-08:57+0000) multi-call binary
Starting pid 9, console /dev/tts/0: '/etc/init.d/rcS'
Algorithmics/MIPS FPU Emulator v1.5
Reading Standard Configuration File /etc/led.conf
Configured 19 states
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/net/avalanche_usb/avalanche_usb.o
USB: Entering USB_init_module.
USB Driver built for RNDIS-CDC protocols.
Error getting protocol configuration from bootloader environment.
Defaulting to "RNDIS-CDC" mode.
USB: Error getting mac from bootloader enviroment for usb0
USB: Using default mac address: 00.E0.A6.66.41.EB
USB: Error getting mac from bootloader enviroment for usb0
USB: Using default mac address: 00.E0.A6.66.41.E1
VID = 0x451
PID = 0x6060
No Serial Number String present.
Manufacturer = Texas Instruments
Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
USB: Entering USB_Init.
USB: Leaving USB_Init.
Default Asymmetric MTU for usb0 1500
USB: Leaving USB_init_module.
Using /lib/modules/2.4.17_mvl21-malta-mips_fp_le/kernel/drivers/atm/tiatm.o
registered device TI Avalanche SAR
Sangam detected
DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
DSP binary filesize = 356930 bytes
tn7dsl_set_modulation : Setting mode to 0x1
Texas Instruments ATM driver: version:[6.00.01.00]
Waiting for enter to start '/bin/sh' (pid 30, terminal /dev/tts/0)
Please press Enter to activate this console. hello_busybox
hello_busybox
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
SIOCGIFFLAGS: No such device
Doing BRCTL ...
addbr br0
Dtn7dsl_set_modulation : Setting mode to 0x1
oing BRCTL ...
addbr br1
Doing BRCTL ...
addbr br2
$$$$start server flag can not find
$$$$start server flag can not find
$$$$start server flag can not find
Sep 8 12:00:18 cfgmgr(snmpcm): snmpd starts (1)
Sep 8 12:00:18 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Sep 8 12:00:18 cfgmgr(sar): DSL Polling Timer Started succesfully.
Sep 8 12:00:18 cfgmgr(sar): doing modulation_set.
Sep 8 12:00:18 cfgmgr(fdb): Firewall NAT service started
Sep 8 12:00:18 : Error getting protocol configuration from bootloader environment.
Sep 8 12:00:18 : Defaulting to "RNDIS-CDC" mode.
Sep 8 12:00:18 USB: Error getting mac from bootloader enviroment for usb0
Sep 8 12:00:18 USB: Using default mac address: 00.E0.A6.66.41.EB
Sep 8 12:00:18 USB: Error getting mac from bootloader enviroment for usb0
Sep 8 12:00:18 USB: Using default mac address: 00.E0.A6.66.41.E1
Sep 8 12:00:18 : VID = 0x451
Sep 8 12:00:18 : PID = 0x6060
Sep 8 12:00:18 : No Serial Number String present.
Sep 8 12:00:18 : Manufacturer = Texas Instruments
Sep 8 12:00:18 : Product description = Texas Instruments CDC Ethernet/RNDIS Adapter
Sep 8 12:00:18 USB: Entering USB_Init.
Sep 8 12:00:18 USB: Leaving USB_Init.
Sep 8 12:00:18 : Default Asymmetric MTU for usb0 1500
Sep 8 12:00:18 USB: Leaving USB_init_module.
Sep 8 12:00:18 : registered device TI Avalanche SAR
Sep 8 12:00:18 : Sangam detected
Sep 8 12:00:18 DBG----: autopvc_enable=1(1: autoPVC ok, 2: unK=1 and 54chg, 3: unK=0 Greg's suggestion) chInfo.FwdUnkVc set to 1.
Sep 8 12:00:18 : DSP binary filesize = 356930 bytes
Sep 8 12:00:18 tn7dsl_set_modulation : Setting mode to 0x1
Sep 8 12:00:18 Texas Instruments ATM driver: version:[6.00.01.00]
Sep 8 12:00:18 tn7dsl_set_modulation : Setting mode to 0x1
Sep 8 12:00:18 : Default Asymmetric MTU for br0 1500
Sep 8 12:00:18 cfgmgr(lanbridge0): Bridge Created: br0
Sep 8 12:00:18 : Default Asymmetric MTU for br1 1500
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
addif br0 eth0
Sep 8 12:00:19 cfgmgr(lanbridge1): Bridge Created: br1
Doing BRCTL ...
setfilter br1 0
Sep 8 12:00:19 cfgmgr(lanbridge2): Bridge Created: br2
Doing BRCTL ...
setfilter br2 0
Doing BRCTL ...
stp br0 off
Doing BRCTL ...
stp br1 off
Sep 8 12:00:20 cfgmgr(lanbridge0): Bridge Interface Added: eth0
$$$$start server flag can not find
Doing BRCTL ...
setfilter br0 0
Doing BRCTL ...
stp br2 off
Sep 8 12:00:21 : Default Asymmetric MTU for br2 1500
Sep 8 12:00:24 : Default Asymmetric MTU for wlan0 1500
Sep 8 12:00:24 cfgmgr(ap): AP Driver configuration successful
Sep 8 12:00:27 cfgmgr(ap): AP IS UP
Sep 8 12:00:27 :
Doing BRCTL ...
addif br0 wlan0
Sep 8 12:00:27 : !!!!!!tiap_param_set_max_user_num val=30
Sep 8 12:00:27 : dda_ioctl_priv_go call wdrv_init
Sep 8 12:00:27 244:
Sep 8 12:00:27 802.11d is 244: ** Enabled **
Sep 8 12:00:27 244: 802.11h is 244: disabled.
Sep 8 12:00:27 244: Country String is: 'CN '
Sep 8 12:00:27 244: Configuration succeeded !!!
Sep 8 12:00:27 244: WLAN driver database is up
Sep 8 12:00:27 : Resetting the remote device.
Sep 8 12:00:27 : Un-resetting the remote device.
Sep 8 12:00:27 : About to re-init the VLYNQ.
Sep 8 12:00:27 : Re-initialized the VLYNQ.
Sep 8 12:00:27 245: AcxRegAddr = 0xA4040000, AcxMemAddr = 0xA4000000
Sep 8 12:00:27 245: whal_acxProcInitiate: found DEVICE_VENDOR ID = 0x9066104c
Sep 8 12:00:27 245: whal_acxProcInitiate: Cpu halt -} download code
Sep 8 12:00:27 245: whal_acxProcLoadFwImage: 0xa4000000, 0x0
Sep 8 12:00:27 245: whal_acxProcLoadFwImage() -- Loading FW image245: Compiled for RADIA (bg) radio
Sep 8 12:00:27 245: whal_acxProcLoadFwImage: 1, pBuf=0xc00af9d0, len=0x15564. Extra pBuf=0x0, len=0x94cfbd09
Sep 8 12:00:27 cfgmgr(lanbridge0): Bridge Interface Added: wlan0
Sep 8 12:00:27 245: whal_acxProcLoadFwImage: 2, pBuf=0xc00af9d0, len=0x15564. Extra pBuf=0x0, len=0x94cfbd09
$$$$start server flag can not find
Doing BRCTL ...
setfilter br0 0
Sep 8 12:00:28 245: whal_acxProcLoadFwImage: 3, pBuf=0xc00af9d0, len=0x15564, DataLen=0x1555c
Sep 8 12:00:28 245: whal_acxProcLoadFwImage: 4, pBuf=0xc00af9d0, len=0x15564
Sep 8 12:00:28 245: whal_acxProcLoadFwImage: Checksum, calc=0x71e76f, file=0x71e76f
Sep 8 12:00:28 255: Tx is up
Sep 8 12:00:28 : wdrv_init call wlan_memMngrInit
Sep 8 12:00:28 : firstFreeMSDU reset!!!!
Sep 8 12:00:28 255: MemMngr is up
Sep 8 12:00:28 255: main state machine is up
Sep 8 12:00:28 276: WDRV_MAINSM: WLAN Driver initialized successfully
Sep 8 12:00:28 :
Sep 8 12:00:28 276: WDRV_4X: 4x Disabled
Sep 8 12:00:28 276: WDRV_4X: Concatenation Disabled
Sep 8 12:00:28 276: WDRV_4X: Ack Emulation Disabled
Sep 8 12:00:28 276: whal_apiStartBss: Enable Tx, Rx and Start the Bss
Sep 8 12:00:28 276: ----------------------------------------------------------------
Sep 8 12:00:28 276: ----------------------------------------------------------------
Sep 8 12:00:28 276: START BSS, SSID=BAVO, BSSID=00-D0-D0-B8-56-89
Sep 8 12:00:28 276: ----------------------------------------------------------------
Sep 8 12:00:28 276: ----------------------------------------------------------------
Sep 8 12:00:28 276: AP Power Level = 1
Sep 8 12:00:28 276: Regulatory Domain = ETSI
Sep 8 12:00:28 276: Net[0] : Channel=11
Sep 8 12:00:28 276: ----------------------------------------------------------------
Sep 8 12:00:28 276: FW Watchdog is Enabled
Sep 8 12:00:28 tiwlan_ddaDoIoctl : Unknown ioctl 35143
Sep 8 12:00:28 dda: Both buf and buf_len must be valid.
Sep 8 12:00:40 : DSL in Sync
Sep 8 12:00:48 cfgmgr(sar): DSL Carrier is up |
|Archiver|小黑屋|宽带技术网
|网站地图
发表于 2008-8-5 22:57:02
发表于 2008-8-5 23:48:02
发表于 2008-8-6 00:06:20
发表于 2008-8-6 10:15:30
