Broadcom路由DSL猫用的JTAG工具最新版

hugebird

2.0.5

-  修正ft2232/jlink写入速度慢的错误
-  允许/window:XXXXXXXX 参数单独与backup/flash命令一起使用，
   避免custom的复杂定义
-  BCM7401参数变更为Little Endian,对于无法识别的BCM STB芯片可以
   加/skipdetect开关，一般可尝试/window:1e000000

hugebird

MINE 发表于 2011-4-7 16:31
用v2.0.4和并口数据线，连接HG522BBA（bcm6358），要么找不到CPU，要么偶尔找到，就会出现以下错误：

在我的机器上测试了，没出现问题，不会是操作系统的问题吧，也可以用/io2试一下
貌似cpu id检测也有问题

hugebird

tom-jerry 发表于 2011-4-8 17:25
回复 tom-jerry 的帖子

有谁用brjtag成功读出bcm6368芯片的cfe？若成功，请说明下是哪个版本，使用哪些参数 ...

brjtag一直就是在6358设备上开发出来的，除了1.0其他版本都支持。不知道你用的是哪种cable，
并口线不要加/cable：0参数。
/skipdetect /fc都不要加

提了多少遍的问题，注意执行brjtag和各设备加电的间隔。注意cpu是否进入debug模式

uzer222

hi!
can you add support storlink sl3516 based on FA526 core (CS351X) or give JTAG instructions for access to memory flash?

pttt

Hugebird 你好，我的HG227改CFE变砖了，用2.0.5版本的写入CFE，识别到CPU是BCM5354 REV 03 ，识别不到闪存，实际是S29GL128P11TF101,于是手动指定/FC:88参数，可以写入，但始终提示：
DMA Read(x2) Addr = 1c000a6e  Data = (00000000)ERROR ON READ
DMA Read(x2) Addr = 1c000a6e  Data = (00000000)ERROR ON READ
写入完成后也不能启动，请帮我看一下怎么解决，谢谢！

附以下信息供参考：
C:\jtag>brjtag -probeonly /erasechip /fc:88

        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================


Probing bus ... Done

Detected IR Length is 8

CPU assumed running under LITTLE endian

CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***

    - EJTAG IMPCODE ....... : 00000000100000010000100100000100 (00810904)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS16 MIPS32

Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor Entered Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
*** Manually Selected a Spansion S29GL128N/P Uni  (16MB) from AMD/Spansion

Operation will take 1 or 2 minutes. Don't break!!!
Erasing whole chip ... Done!



*** REQUESTED OPERATION IS COMPLETE ***


C:\jtag>brjtag -flash:cfe /fc:88

        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================


Probing bus ... Done

Detected IR Length is 8

CPU assumed running under LITTLE endian

CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***

    - EJTAG IMPCODE ....... : 00000000100000010000100100000100 (00810904)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS16 MIPS32

Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor Entered Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
*** Manually Selected a Spansion S29GL128N/P Uni  (16MB) from AMD/Spansion

    - Flash Chip Window Start .... : 1C000000
    - Flash Chip Window Length ... : 01000000
    - Selected Area Start ........ : 1C000000
    - Selected Area Length ....... : 00040000

*** You Selected to Flash the CFE.BIN ***

=========================
Flashing Routine Started
=========================
Total Blocks to Erase: 2

Erasing block: 1 (addr = 1C000000)...Done
Erasing block: 2 (addr = 1C020000)...Done

Loading CFE.BIN to Flash Memory...
DMA Read(x2) Addr = 1c000a6e  Data = (00000000)ERROR ON READ
DMA Read(x2) Addr = 1c000a6e  Data = (00000000)ERROR ON READ
Done  (CFE.BIN loaded into Flash Memory OK)

=========================
Flashing Routine Complete
=========================
elapsed time: 1033 seconds


*** REQUESTED OPERATION IS COMPLETE ***

pttt

另外我用的是自制的简易并口JTAG线，线长只有15CM，接台式电脑原生并口。

yesup

这个重要888

pttt

运行BRJTAG2.0.5时会提示“应用程序错误”见附图。

yesup

1.6r 支持了
S29GL128P10 留爪

1330916

谢谢你,辛苦了 :)