|
|
楼主 |
发表于 2024-12-31 08:32:38
|
显示全部楼层
=> help
? - alias for 'help'
base - print or set address offset
bdinfo - print Board Info structure
bootm - boot application image from memory
bootp - boot image via network using BOOTP/TFTP protocol
cmp - memory compare
cp - memory copy
crc32 - checksum calculation
dcache - enable or disable data cache
dm - Driver model low level access
downver - upgrade images for chip
editenv - edit environment variable
env - environment handling commands
fdt - flattened device tree utility commands
fpga - help fpga -r [module 0:pon 1:pps 2:nppt 3:rgmii 4:xpcs 5:uniserdes 6:ponserdes 7:top_crm 8:sys_ctrl][reg - %%x] [number - %%d] fpga -w [module 0:pon 1:pps 2:nppt 3:rgmii 4:xpcs 5:uniserdes 6:ponserdes 7:top_crm 8:sys_ctrl][reg - %%x] [data - %%x]
help - print command description/usage
icache - enable or disable instruction cache
idm_rx_debug- set idm rx debug
idm_tx_debug- set idm tx debug
idm_tx_outport- set idm tx outport
loadb - load binary file over serial line (kermit mode)
loads - load S-Record file over serial line
loadx - load binary file over serial line (xmodem mode)
loady - load binary file over serial line (ymodem mode)
loop - infinite loop on address range
mcupg - multicast upgrade
md - memory display
memtester - do memory test
mii - MII utility commands
mm - memory modify (auto-incrementing address)
mtd - MTD utils
mw - memory write (fill)
nand - NAND sub-system
nboot - boot from NAND device
netdebug - set net debug count
nm - memory modify (constant address)
np_init - set net debug count
panic - Panic with optional message
ping - send ICMP ECHO_REQUEST to network host
printenv - print environment variables
pserdes - pserdes init_change [mode]
pserdes_133- pserdes init_change [mode]
pvt_133 - PVT utility commands for 133
pwm - PWM utility commands
reset - Perform RESET of the CPU
run - run commands in an environment variable
saveenv - save environment variables to persistent storage
setenv - set environment variables
sky_bakeup_info- sky bake up all the info
smac_check_phy- smac check phy
smhload - load a file using semihosting
spa_port_attr_op- help spa_port_attr_op set_port_attr [data] [mem_id] [port_attr_id]spa_port_attr_op get_port_attr [mem_id] [port_attr_id]
submpasswd- Set uboot menu password for safe boot mode
swsfmd - Manually switch to safe boot mode
tftpboot - boot image via network using TFTP protocol
up_mode - up_mode - up_mode set/get
userdes - help userdes init_change [uni][mode], MODE_SGMII 0, MODE_HSGMII 1,MODE_USXGMII_2P5G 2,MODE_5GBASE_R 3,MODE_USXGMII_5G 4,MODE_10GBASE_R 5,MODE_USXGMII_10G 6
userdes_133- userdes_133 init_change [mode]
version - print monitor, compiler and linker version
xmac_test - help xmac_test set_ponserdes_to_xmac1 [en]xmac_test xmac_work_mode_set [xmac_id] [work_mode]
zxboot - boot zx soc images
zxvid - zxvid get|set|getall
|
|
粤公网安备44152102000001号 
发表于 2025-3-1 16:22:29