Available commands:3 T* @" n, V5 `& [( M: @4 Y
( s, G2 _3 p( z# [: [+ g cotpcfg Reading/fusing potp/sotp bits& U+ t% O" n9 I# `; O, J$ f! ?* E
unimac_stats Show UNIMAC port statistics/ Y; }4 D1 h/ [* |) d
set_dump Dump all recieved packets on active port& t- H/ v! k1 f/ [" o
net_stats Get network ports status% Y( C+ F5 Q1 M. G* w
vrpd View Ring packet descriptor
5 d4 k; v* U. m& M( ^sar Show available Runner to CPU rings' Z# I# _* v. Q" X8 M1 f9 v3 ~; e
erase_misc_parti Erase misc partition
! ^. p. [' ]0 g- H$ P# ]# f# ^x Change extra partitions size" H0 C1 N3 T& H" B: N' S
find Find string in NAND
0 j7 a1 U( N; y# J2 Fcomp Compare NAND blocks0 M/ z2 T" l$ M+ f5 [# W: d( H
bb Find NAND flipped bits by comparing a read with and without ECC$ @0 w% p. z3 F! _5 p
fb Find NAND bad blocks
+ Y, n- @, k6 y. A+ `rn Read NAND contents along with spare area with ECC off( o4 M5 _$ q; k6 Z8 }
dn Dump NAND contents along with spare area
. C! o b/ a" S; D7 P4 vphy Set memory or registers.7 C7 ]6 I+ J0 e
meminfo Display CFE System Memory
t# g2 ?) }6 Z4 q; `* B- Wkernp Updates extra bootloader parameter for kernel. To end input enter // consecutively at any time then press <enter>
# \+ E6 s7 ?. _' N+ Xsm Set memory or registers.4 l# a+ W( z( _' z( A" I7 T
swrp Enumerate power supplies1 m g+ |% |" |. D$ {+ Q
swrd Dump SWREG; [, \: W$ P! s% ^' y3 b. a8 V
swrw Write SWREG
3 ?2 i$ R1 ~' o& b! Lswrr Read SWREG( m0 e7 y% E' X- f6 O/ W
db Dump bytes.( m! n# e4 ?( o, g" N
dh Dump half-words.
# v: G ~& e5 }1 [. hdw Dump words.
: s4 @! y! Q1 x" U0 h- Dddw Dump dwords.
/ ]& Y% R7 Y; Q' s7 @7 dw Write the whole image start from beginning of the flash# i" c* |' K4 _6 ] P; O7 q
e Erase NAND flash
2 {% u0 E E O9 ewp Write pmc (previously loaded through JTAG to flash block 0.# i" |3 c9 b" r3 _7 I
ws Write whole image (priviously loaded by kermit or JTAG) to flash .8 ~0 P0 z6 |# `) W |
ba set linux kernel boot argument1 L2 n' N6 H a
ldt load device tree blob from tftp server.) \; I2 Z9 E, G3 n- G! }4 p
go goto and execute from specefic address.
( i/ U$ {3 M7 |) o8 I* Tloadb load binary via network or kermit protocol.
3 u& S9 i, w4 G, o) k1 t% jr Run program from flash image or from host depending on [f/h/c] flags; ?0 ]- {! N5 }' F& i
p Print boot line and board parameter info
# m* G+ S+ G7 \ `c Change booline parameters/ ~+ j6 L" p4 Z! d, o) G% D+ B- f, t
i Erase persistent storage data# } \, t1 ]. c( D6 _
ddr Change board DDR config s6 V9 O7 R5 J; v3 Y& W
a Change board AFE ID, I- G2 J {$ G$ ?
b Change board parameters
. X w3 H) c) N; Greset Reset the board# }! e, Q( P! q; T
pmdio Pseudo MDIO access for external switches.
# _; k5 [, L- V5 }spi Legacy SPI access of external switch.
4 P% u, H4 F6 vpmclog pmclog: H0 {- R7 k; L6 @# k: |" T1 s! l
pmc pmc cmd+ Y& ^# _$ h. h1 k0 k7 K0 @1 W% o
closeavs pmc close avs cmd: s4 F! A2 n% |. d! x" x# J
force override chipid check for images.) L( u3 D4 s$ M; S7 ?) O1 u
help Obtain help for CFE commands
& |: d `+ K" {+ g
( P0 W" D* }) p( F+ O2 iFor more information about a command, enter 'help command-name'
2 [3 l" O6 r |$ q5 U+ i, T*** command status = 0 |
粤公网安备44152102000001号 
发表于 2023-1-14 10:57:51
