|
|
之前发了这个帖子是在路由器连接TTL线通电后出现的开机自检信息，帖子详情：https://www.chinadsl.net/forum.ph ... d=171246&extra=，这次我按紧复位键插电源后，貌似进入自动刷机模式，显示TFTP，但具体要怎么操作，谁能看懂指导我一下，谢谢！
# S! X* | [' {2 A; p: C& M
( z( g% R( E' _. ~. @& n
! @7 X- y( v% |7 F" G0 I& VU-Boot 1.1.3 (Oct 9 2013 - 09:14:54)
8 l' y0 P2 H- t9 Z
6 K0 E# V- x+ W6 v/ PBoard: Ralink APSoC DRAM: 64 MB+ c" a0 ?2 h0 l. o8 a+ Y, j2 Z0 H8 \5 q
relocate_code Pointer at: 83fb00003 u3 @: E. c4 B o4 k9 h0 M. G
8 e s; [! S7 {8 @ Set info->start[0]=BC000000
2 `. P$ C# ~6 Eflash_protect ON: from 0xBC000000 to 0xBC01D24B( u6 @' S+ O9 F* y3 T- D/ V! j
flash_protect ON: from 0xBC030000 to 0xBC030FFF
) q8 P2 I1 d/ A! x& V*** Warning - bad CRC, using default environment5 Z1 c) a+ j5 ?; ~9 P
+ o2 ^1 Q! _7 H- i; [% a- m============================================ 5 |; V$ J* }" P2 s% l# ]6 V R& v
Ralink UBoot Version: 4.1.1.0
$ O7 k1 f( n, h--------------------------------------------
$ [1 C4 \: }- B& uASIC 3883_MP (MAC to Realtek Mode)
+ u/ O( e2 L9 p9 u& gDRAM component: 512 Mbits DDR, width 16
- h% X: j2 Q- ?8 j( s, VDRAM bus: 16 bit
1 ]% j) s, O& e6 k8 |, {! N0 VTotal memory: 64 MBytes( h j# L4 f: L9 \
Flash component: NOR Flash
X% @, J" k; y2 }% uDate:Oct 9 2013 Time:09:14:541 W0 T2 \, l: x
============================================ 7 _6 M8 j. W8 x) t u* c* ^
icache: sets:512, ways:4, linesz:32 ,total:65536
* v% \% w& @8 l4 a7 ?# _" ldcache: sets:256, ways:4, linesz:32 ,total:32768 9 z- P9 r9 z- Z3 u. Q
Z/ e* J* ~- R$ [9 z. [ ##### The CPU freq = 480 MHZ #### 9 U) b4 `, ]- _8 R2 r
estimate memory size =64 Mbytes
. V* v6 D8 z2 J5 D& kReset pressed, entering rescue mode!
1 ^& t. t- v( k5 D1 P! ^
3 `% [- Q( u% h/ b+ q3 F( Z4 h3 z
9 h) X: f& ^' {2 b& S5 ]( ]; S: d10: System Load Firmware then write to Flash via TFTP. ) R/ b, H+ o9 s4 l4 T
Input device IP (192.168.1.123) Input server IP (192.168.1.100)Input Linux Kernel filename () 1 L* V$ g0 [& u% u7 ~! T2 |- R& T
netboot_common, argc= 3 1 p" G5 i, N2 ^+ O: ?3 a
2 X8 A& A$ k0 O0 ]- _* w3 S8 ^
NetTxPacket = 0x83FE5900
& I+ ^0 z1 U" @9 M. k. h9 v K8 u! u i; |: Q
KSEG1ADDR(NetTxPacket) = 0xA3FE5900
- ~3 N2 g( _+ F: w
" y- T' s1 P/ K4 w0 T* j NetLoop,call eth_halt !
3 x% e% K, E. `% u" I& v
, L! _+ n! R' ~) ^. i1 c NetLoop,call eth_init !
7 |6 V8 }6 T( f% l( aTrying Eth0 (10/100-M)
9 ^6 A3 G2 c& K C+ ~) x4 q
( V1 n& X9 e/ B% I5 e Waitting for RX_DMA_BUSY status Start... done3 R* s* B4 d1 [5 v, y6 B* v- v
9 M) Q( W4 V- W6 r' W) b& v1 P+ o
* q/ q' I7 p4 ~+ Y7 M; c' ^ Realtek giga Mac support
! e* l4 H7 n; h& u
" @! E" e( \$ e9 D, z+ l6 S8 D GPIO pin 24 reset to switch
. G* E! b: S( e: ~1 {& j% } o% ]# v0 q
ETH_STATE_ACTIVE!! + e/ g" n& a+ M2 f# Z1 w8 q- @4 P
TFTP from server 192.168.1.100; our IP address is 192.168.1.123
) ]- n8 ^" \0 E% |5 g8 HFilename 'firmware.bin'.
9 e- e& q% K) W) f8 A! a9 i# q" y( C4 X
TIMEOUT_COUNT=10,Load address: 0x80100000
- N% u' b5 j' {9 e+ W) c( y5 LLoading: T T
. K M+ [6 f0 s' c1 z8 P
) j, I& A' D1 t' j# Y4 S8 ^! P3 n |
|
粤公网安备44152102000001号 
发表于 2022-3-24 22:19:22