|
|
HuaWei StartCode 2012.02 (V300R017C10 Nov 16 2017 - 08:37:22)
2 W% k) C9 g! h c' F5 i- a/ ?* k% n
* _7 k- e9 i7 E2 J9 s- `1 r0 v& ANAND: Nand ID: 0xC8 0xDA 0x90 0x95 0x44 0x7F 0x7F 0x7F E0 Y* U: J5 b
ECC Match pagesize:2K, oobzie:64, ecctype:4bit% q6 y- K, M6 }% ^
Nand(Hardware): 256 MiB
" U% h) }7 [. ^0 ~startcode select the uboot to load
& V) `- c; i- }# qthe high RAM is :8080103c
, j/ E7 V$ b* }* n, Cstartcode uboot boot count:10506824360 G h) F. c4 z' ]" n
use the main slave_param area from flash, the RAM data is not OK!!!9 }7 I9 b8 x; R& |4 S: r
Use the UbootB to load first5 ?7 x! G2 B& z, W4 |6 P' H
Use the UbootB to load success1 e, U# ?2 M3 g# o
5 g( L* U- P3 r$ W& I. Q7 q8 f! A
/ v3 p3 L9 U6 G3 T3 D5 @5 K! N8 _U-Boot 2010.03 (V300R017C10 May 12 2017 - 01:41:52)0 x2 z2 v+ `* n1 _* A
: c+ t/ c' W2 ^# q: Z J
Mbist flag = 0x0, ddr totoal size = 0x10000000
- K* G; H) m) z% n( c5 u7 xDRAM: 256 MB
" V" K* V. g/ H5 } UBoot From NAND flash) Y4 q6 @$ \7 V8 U, H
Chip Type is SD5116H
) w9 U7 i n, GNAND: Special Nand id table Version 1.23
. h' m, r% u$ h5 cNand ID: 0xC8 0xDA 0x90 0x95 0x44 0x7F 0x7F 0x7F8 _) o+ p; ]* {/ J4 ?8 P) }
now using default nand flash type, Block:128KB Page:2KB!
2 [) S$ U$ @& n3 E* pECC Match pagesize:2K, oobzie:64, ecctype:4bit
" Q6 P# ~! u7 l0 qNand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bit
3 E, \. e& E6 r* C+ [128 MiB) X( }, w! o( `! I/ b' K( m0 r
Using default environment
% ~0 y! U# n: w4 H# s# c
; H8 G2 t, i$ t/ J1 }+ \In: serial
1 k: S) Y: A. z1 y4 Y4 A# rOut: serial
+ M( ]$ d- @1 p) @) d2 c5 e# l+ ^Err: serial
: m/ t+ J. a; d7 APHY power down !!!2 q9 {4 v- U. N& Y
[main.c__6102]::CRC:0xc2c2c50, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, CommitedArea:0x1, Active:0x0, RunFlag:0x2% `" m1 a% f4 R/ L+ L! c
Start from main system(0x1)!' @+ `) c7 x2 l& i$ ?
CRC:0xc2c2c50, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x1, Active:0x1, RunFlag:0x25 s6 i: c3 Y1 m' h
0x000000100000-0x000008000000 : "mtd=1"
" U2 a8 }% v4 [2 c+ CUBI: attaching mtd1 to ubi07 p2 p4 K% N+ _ A
UBI: empty MTD device detected9 }5 g& k/ d0 Q0 p6 J: h) j. q
UBI: create volume table (copy #1)( l$ f3 @* \+ T& U: s
UBI error: ubi_scan_get_free_peb: no eraseblocks found
/ Z8 D) K5 U+ R1 E7 m, VUBI error: ubi_init: cannot attach mtd1- l2 O4 l8 n0 W. A' j9 T7 A
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
+ f. _6 J: T/ T, V- Y" w9 S# @8 ?UBI init error -28
: ~0 q5 f" g4 kERROR: failed to select 'ubifs' partition, please format it first!
' G7 {) v& V. ]resetting ...
+ O1 R$ m0 m/ {* S: c* A5 ]5 O" L5 `8 l
0 L$ h! X9 B$ O& \; c/ _) o) E/ f0 B& j |
|
粤公网安备44152102000001号 
发表于 2022-1-21 14:44:50