|
|
楼主 |
发表于 2021-1-15 15:48:22
|
显示全部楼层
这是ttl线跑出来的光猫部分的
: S$ u) i8 c8 k* Q8 ~: uBoot NAND
! p: s! {7 L _+ IC
( n, @2 [1 G' w6 E- w- ]+ P! c7 g7 G+ d' b: O5 f o' g9 G
U-Boot 2013.04-svn10364 (May 24 2019 - 19:10:44) A4 M; d2 Q5 O' K
$ B2 v N) `# W4 J8 l: H
CPU : ZX279127@A9,800MHZ
& R) a" M0 o3 t& k- X& M* \( {Board: zxic zx279127evb
" k* R# j6 L+ W' G* ]( bDRAM: 256 MiB
4 v' T/ r! X1 ?com1
7 D f! c' d8 R: `6 N7 U: ]4 _* Aproduct_vid = 66
- _* u" b: w% q( `; v* ?( V$ Mvid=66-F627
, Z, [# i+ G# ~9 H4 s5 O- z/ g1 uoutput gpio:1, value=1, 0
* b9 ~7 n: } Z4 i9 ZNAND: NAND_special nand special:0
5 J7 Z% i% M. }( T) I- ?) g% L
2 C1 n7 ]: a, P8 ~4 u; uManu ID: 0xad, Chip ID: 0xda (Hynix NAND 256MiB 3,3V 8-bit)
: _5 x# s/ l2 M256 MiB: Q/ Z. D3 m% f1 K1 Q4 u
<nand_read_skip_bad_,1308>!mtdpart=0x1,offset=0x0,mtdpartoffset=0x180000,mtdPartsize=0x80000,length=0x20000
# l5 e. H8 i WIn: serial' ~* v7 @/ E+ ^/ k
Out: serial: Q9 m9 `6 I7 l
Err: serial- i$ A1 ^1 v* ^, Q
clk_pll env is not setted, core clk won't change
% @, S3 o5 _2 \7 h' SNet: addr 0x94000008 before value is f9ff1fcf
) L; [7 V. O, Z, }addr 0x94000008 after value is ffff1fcf
/ s+ }; i [- z5 t- x* |1 H' Yserdes init done3 m8 J$ J6 C5 q3 K/ k4 s
init fe_phy first!
8 D t" p+ i$ e5 a% f, E; S- ginnerGeLedPolarSet 0
8 l7 f- K" t" m+ v2 Ieth03 E' X8 r- _1 d6 H4 u% ]
3 I( o$ C" D1 W' IHit 1 to upgrade software version
" B j( V5 H4 h+ C* d; U) @Hit any key to stop autoboot: 1 0
! A1 ?# B- D/ S8 edo_mcupg function enter..% R6 t0 m |2 E2 G; G/ @+ \& q$ O0 r
mac 4 phy status changed: 10M half-duplex
9 g$ }. p3 T5 S1 F-----smac_init% u. g, W, C# @( `
Using eth0 device |
|
粤公网安备44152102000001号 
发表于 2021-1-15 15:45:21
