|
|
本帖最后由 tao8886999 于 2020-2-4 19:21 编辑
* ^6 d$ |) {9 P8 V( L1 I- i
9 v( y6 B) a( w$ B1 _华为HS8545M移动版因刷错固件变转，电源指示灯亮，网口通。接TTL线终端显示如下信息：
7 H7 X5 Y" ^7 t7 N+ X) V! f
" r5 u/ S2 ~1 d# o3 c$ ^HuaWei StartCode 2012.02 (V300R017C10 Sep 07 2017 - 11:54:40)+ o# S2 T! A7 p$ h) M" u& z
NAND: Nand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
- r! a: f4 A% {7 bECC Match pagesize:2K, oobzie:64, ecctype:4bit& o" v' \" a2 }
Nand(Hardware): 256 MiB
! A' F) n$ \! D# ^/ s: ~startcode select the uboot to load
$ M; P" ?3 T j1 ]9 |the high RAM is :8080103c- G( d8 c. D0 Z5 B/ B; f; R
startcode uboot boot count:-1
& Q& u u: m6 e' k& Ause the main slave_param area from flash, the RAM data is not OK!!!
. m0 Q, t7 S2 H8 C* ~3 DUse the UbootB to load first( B6 @( K6 n0 t, a" J
Use the UbootB to load success; y& z% T7 V( S1 e6 [+ J
) e, C2 p0 d8 e5 s5 K p0 R; C
U-Boot 2010.03 (R16C10 Mar 10 2016 - 23:50:04)
; K% ]1 E4 x7 k5 u4 oDRAM: 256 MB
7 t3 j3 s4 ?0 j, Z$ M8 I4 nBoot From NAND flash5 y* A7 K3 b1 ^
Chip Type is SD5116H
2 E; A2 S" T% ]NAND: Special Nand id table Version 1.23
7 W. a: m: q* t# a1 K3 i) v) l) d3 }: KNand ID: 0xC2 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
5 c( F# B% [* F S+ ~0 G" Xnow using default nand flash type, Block:128KB Page:2KB!
4 I2 ^5 t4 x& Y- X6 |, R/ ~ECC Match pagesize:2K, oobzie:64, ecctype:4bit
& E) {6 M N H6 l5 |3 q$ o5 C% xNand(Hardware): Block:128KB Page:2KB Chip:128MB*1 OOB:64B ECC:4bit
: B8 e* t9 _9 o( e A9 u128 MiB
* s& @2 p' b) J8 `Using default environment
4 J& X* H& n8 {& |& dIn: serial
7 `) V# R7 D/ |1 Q r3 NOut: serial
5 @0 N7 \. q2 }( X" a% P/ U% y0 \Err: serial
+ y8 S( d) h, u, Q ^4 r& @[main.c__6080]::CRC:0xc2c2c50, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:0, Co
3 |% _4 I; b2 M1 |; rmmitedArea:0x1, Active:0x0, RunFlag:0x2; l, A/ ~; s; u7 a& i. w, [
Start from main system(0x1)!3 n9 r8 G8 s! ?0 q8 s/ m
CRC:0xc2c2c50, Magic1:0x5a5a5a5a, Magic2:0xa5a5a5a5, count:1, CommitedArea:0x1,# n9 k/ o' z }1 B2 W7 ~
Active:0x1, RunFlag:0x24 ?! g9 ^( n9 j6 | K
0x000000100000-0x000008000000 : "mtd=1"3 w$ `6 i) i4 {2 L" |( d, m
UBI: attaching mtd1 to ubi0
% B* \7 e/ z- I* S" XUBI: empty MTD device detected
9 {& V. r4 O: u, XUBI: create volume table (copy #1)
Z3 K% S1 X- b# Y+ ?5 {: w% ]UBI error: ubi_scan_get_free_peb: no eraseblocks found% \/ n+ p, {# @& ~% L. I* d* Q
UBI error: ubi_init: cannot attach mtd1) S4 e9 d" F0 k# f
UBI error: ubi_init: UBI error: cannot initialize UBI, error -28
4 n6 F; P I& A7 RUBI init error -280 M3 d$ a+ c8 y4 X
ERROR: failed to select 'ubifs' partition, please format it first!
4 ~+ C5 n2 ^9 w5 Z5 Qhisilicon #! Y& d4 v: g; Z1 {0 w$ ]. I& R
9 |7 m; |# J* o. u) r2 C
提示：加载mtd1失败，无法选择“ubifs”分区，请先格式化它！
# V2 h4 B0 E; ~* ?0 P S S% L- H& ?( {求大神提供格式化“ubifs”分区的命令及救砖办法？
, g% x4 V$ y4 M, C谢谢指导！！!
* B t4 C! Q& B& A8 | f2 @
" @3 e" D, A; A# c9 o3 Q1 _8 b l6 e
|
|
粤公网安备44152102000001号 
发表于 2020-2-4 19:20:07