哈哈 我成功了 绝对原创

kuangmsn

在这里特别感谢harrybest  大哥
偶是菜鸟，以前有个mt800，电信租借来的，被偶刷坏了，380元啊 ，心疼ing
又给了一个新的mt800，这个猫和以前的那个不一样，默认密码变成了epicrouter
版本是V200R001C01B012sp01 ， 当然了，web的界面也不一样。
因为要bt，但是又不想把路由关了，偶就到这里来看看，
来到这里，我才知道很多兄弟和我的情况是一样的
harrybest说的我的猫是Conexant芯片，我就有了要刷的意思了
可惜找了找去，也找不到一个例子，没发下手啊
到我知道了秒针大哥，哈哈，我就去他的网站看了一下
开始我就弄了一个4.1.0.28（好像就是这个）版本的，刷了上去
成功了，但是旁边的选项没了（可惜没截图），然后又想起了那个叫做EEG的小工具，
就把4.1.0.28这个版本里面的一个文件传了上去，就有了
可惜这个版本好像不稳定，BT老是掉线，后来我就换了现在的这个版本
很稳定，真的
偶的运气太好了， 哈哈
另外有那位大哥能告诉我现在的这个版本做端口映射怎么做啊？

kuangmsn

kuangmsn

02/24/2005 19:24:57> Send UPnP Connected
02/24/2005 18:30:13> UPnP Action:DeletePortMapping State:Success. TCP-port:10315 Closed!
02/24/2005 18:22:08> UPnP Action:AddPortMapping State:Success. TCP-port:10315 Opened!
02/24/2005 15:43:10> Send UPnP Connected
02/24/2005 15:35:02> UPnP Action:DeletePortMapping State:Success. TCP-port:20431 Closed!
02/24/2005 15:35:02> UPnP Action:DeletePortMapping State:Success. TCP-port:19663 Closed!
02/24/2005 15:32:11> UPnP Action:DeletePortMapping State:Success. TCP-port:19919 Closed!
02/24/2005 15:30:01> Received time from Time Server 129.6.15.29
01/01/1970 00:00:46> UPnP Action:AddPortMapping State:Success. TCP-port:20431 Opened!
01/01/1970 00:00:46> UPnP Action:AddPortMapping State:Success. TCP-port:19919 Opened!
01/01/1970 00:00:25> UPnP Action:AddPortMapping State:Success. TCP-port:19663 Opened!
01/01/1970 00:00:25> UPnP Action:DeletePortMapping State:Success. TCP-port:62162 Closed!
01/01/1970 00:00:25> UPnP Action:AddPortMapping State:Success. TCP-port:62162 Opened!
01/01/1970 00:00:21> Send UPnP Connected
01/01/1970 00:00:20> PPP1 Session is up.
01/01/1970 00:00:20> DNS: Add IP address 61.134.1.9 (Auto discovered)
01/01/1970 00:00:20> DNS: Add IP address 61.134.1.4 (Auto discovered)
01/01/1970 00:00:19> No Static Session Information is defined.
01/01/1970 00:00:19> NAT/NAPT Session Start: interface ppp1, WAN IP is 219.145.197.125
01/01/1970 00:00:19> PPP1: DNS Secondary IP address is 61.134.1.9
01/01/1970 00:00:19> PPP1: DNS Primary IP address is 61.134.1.4
01/01/1970 00:00:19> PPP1: PPP Gateway IP address is 219.145.192.225
01/01/1970 00:00:19> PPP1: PPP IP address is 219.145.197.125
01/01/1970 00:00:19> PPP1 PAP Authentication success
01/01/1970 00:00:19> PPP1 PPPoE Session is established.
01/01/1970 00:00:19> PPP1 PPPoE PADS Received  Service-Name: AC-Name:akbsn1
01/01/1970 00:00:19> PPP1 PPPoE PADR Sent, Service-Name: AC-Name:akbsn1
01/01/1970 00:00:17> PPP1 PPPoE PADI Sent
01/01/1970 00:00:17> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 00:00:17> u/s total bit capacity: 185bits, used: 185bits
01/01/1970 00:00:17> d/s total bit capacity: 1109bits, used: 264bits
01/01/1970 00:00:17> d/s Latency: INTERLEAVED, u/s Latency: INTERLEAVED
01/01/1970 00:00:17> d/s Data Rate: 1024kbps, u/s Data Rate: 640kbps
01/01/1970 00:00:17> d/s Attenuation: 62.0dB, u/s Attenuation: 31.5dB
01/01/1970 00:00:17> d/s SNR: 18.1dB, u/s SNR: 17.0dB
01/01/1970 00:00:17> CO Vendor: TEXAS_INSTRUMENTS
01/01/1970 00:00:17> Max Tx Power: -38dBm/Hz
01/01/1970 00:00:17> Annex Mode: ANNEX_A
01/01/1970 00:00:17> Modulation: G.dmt
01/01/1970 00:00:17> ADSL connected
01/01/1970 00:00:17> ATM layer is up, cell delineation achieved
01/01/1970 00:00:17> ATM Connected
01/01/1970 00:00:06> CfgMgr: ';Washer.dlz'; module loaded.
01/01/1970 00:00:00> CfgMgr: ';Shtm.dlz'; module loaded.
01/01/1970 00:00:00> Verify Firmware OK
01/01/1970 00:00:00> Initialized Dynamic NAPT.
01/01/1970 00:00:00> ATM: Setting up vcc4, VPI=8, VCI=35
01/01/1970 00:00:00> ATM: Setting up vcc3, VPI=0, VCI=50
01/01/1970 00:00:00> ATM: Setting up vcc2, VPI=14, VCI=24
01/01/1970 00:00:00> ATM: Setting up vcc1, VPI=0, VCI=100
01/01/1970 00:00:00> ATM: Setting up vcc0, VPI=8, VCI=35
01/01/1970 00:00:00> ATM: Detected
01/01/1970 00:00:00> Ethernet Device 0 Detected

kuangmsn

秒针大哥  你也很强，感谢了  

燕双鹰

MT800多么贵？我这里有。你要几个我都给你，280就行了。

kuangmsn

我靠 兄弟你也不早说，

yiping

高级配置里面的虚拟服务就是

kuangmsn

大哥 我知道是在这个地方， 问题是我想把所有的端口都开开
怎么弄？？

njly01

找到DMZ，填入你的IP就行了～

BILLYCANE

看不懂，这个原创什么？