关于sa1456c配置

xxcat · 发表于 2016-3-15 00:19:29

确实是我见过的光猫当中比较豪华的。内存512MB，flash 256MB(其实是2GB，只是系统默认只开了256MB)，带了双usb插口，sd卡槽。wifi是常见的RTL8192芯片。主控还是8245H的hi5115t。4个网口都是千兆。这豪华配置足以让许多无线路由器汗颜了。总的来说，这款机器貌似有很大的折腾空间。附bootlog

WAP>display startup info
<5>Linux version 2.6.34.10_sd5115v100_wr4.3 (root@vm1017617813) (gcc version 4.4.6 (GCC) ) #1 SMP Wed Apr 29 10:40:07 CST 2015
<3>PHYS_OFFSET = 80e00000.
<4>CPU: ARMv7 Processor [414fc091] revision 1 (ARMv7), cr=10c53c7f
<4>CPU: VIPT nonaliasing data cache, VIPT nonaliasing instruction cache
<4>Machine: sd511x
<4>Memory policy: ECC disabled, Data cache writealloc
<7>On node 0 totalpages: 127488
<7>free_area_init_node: node 0, pgdat c03dd6e0, node_mem_map c0407000
<7> Normal zone: 996 pages used for memmap
<7> Normal zone: 0 pages reserved
<7> Normal zone: 126492 pages, LIFO batch:31
<4>SD511x chip id:0x51152100
<4>apb bus clk is 100000000
<6>PERCPU: Embedded 7 pages/cpu @c07f4000 s4448 r8192 d16032 u65536
<6>pcpu-alloc: s4448 r8192 d16032 u65536 alloc=16*4096
<6>pcpu-alloc: [0] 0 [0] 1
<4>Built 1 zonelists in Zone order, mobility grouping on. Total pages: 126492
<5>Kernel command line: noalign mem=498M console=ttyAMA1,115200 ubi.mtd=1 root=/dev/mtdblock11 rootfstype=squashfs mtdparts=hinand:0x100000(startcode),0xff00000(ubifs),-(reserved) pcie0_sel=x1 maxcpus=0 user_debug=0x1f panic=1 skb_priv=128
<6>PID hash table entries: 2048 (order: 1, 8192 bytes)
<6>Dentry cache hash table entries: 65536 (order: 6, 262144 bytes)
<6>Inode-cache hash table entries: 32768 (order: 5, 131072 bytes)
<6>Memory: 498MB = 498MB total
<5>Memory: 501388k/501388k available, 8564k reserved, 0K highmem
<5>Virtual kernel memory layout:
<5> vector : 0xffff0000 - 0xffff1000 ( 4 kB)
<5> fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
<5> DMA : 0xffc00000 - 0xffe00000 ( 2 MB)
<5> vmalloc : 0xdf800000 - 0xf8000000 ( 392 MB)
<5> lowmem : 0xc0000000 - 0xdf200000 ( 498 MB)
<5> modules : 0xbf000000 - 0xc0000000 ( 16 MB)
<5> .init : 0xc0008000 - 0xc002c000 ( 144 kB)
<5> .text : 0xc002c000 - 0xc03ae000 (3592 kB)
<5> .data : 0xc03c2000 - 0xc03ddd60 ( 112 kB)
<6>SLUB: Genslabs=11, HWalign=32, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
<6>Hierarchical RCU implementation.
<6>RCU-based detection of stalled CPUs is enabled.
<6>NR_IRQS:160
<6>Calibrating delay loop... 1294.33 BogoMIPS (lpj=6471680)
<6>Security Framework initialized
<4>Mount-cache hash table entries: 512
<6>CPU: Testing write buffer coherency: ok
<7>Synthetic TSC timer will fire each 131104 jiffies.
<6>Init trace_clock_cyc2ns: precalc_mult = 312500, precalc_shift = 8
<6>Brought up 1 CPUs
<6>SMP: Total of 1 processors activated (1294.33 BogoMIPS).
<4>hi_wdt: User-Mode!
<4>hi_wdt: Init sucessfull!
<6>NET: Registered protocol family 16
<6>ACP ON!
<4>ACP bus = 200M!
<6>L2cache cache controller enabled
<6>check_res_of_trace_clock: sched_clock() high resolution
<6>Serial: dw uart driver
<6>uart:0: ttyAMA0 at MMIO 0x1010e000 (irq = 77) is a AMBA/DW
<6>uart:1: ttyAMA1 at MMIO 0x1010f000 (irq = 78) is a AMBA/DW
<6>console [ttyAMA1] enabled
<4>pcie0 sel: 0x1, pcie1 sel:0x0,pcie0 memsize:0xa00000, pcie1 memsize:0xa00000.
<4>PCIE0 Device Link Up val = 0x00008038, loop = 2.
<7>pci 0000:00:00.0: reg 10: [io 0x0000-0x00ff]
<7>pci 0000:00:00.0: reg 18: [mem 0x00000000-0x00003fff 64bit]
<7>pci 0000:00:00.0: supports D1 D2
<7>pci 0000:00:00.0: PME# supported from D0 D1 D2 D3hot D3cold
<7>pci 0000:00:00.0: PME# disabled
<6>PCI: bus0: Fast back to back transfers disabled
<6>pci 0000:00:00.0: BAR 2: assigned [mem 0x40000000-0x40003fff 64bit]
<6>pci 0000:00:00.0: BAR 2: set to [mem 0x40000000-0x40003fff 64bit] (PCI address [0x40000000-0x40003fff]
<6>pci 0000:00:00.0: BAR 0: assigned [io 0x40a00000-0x40a000ff]
<6>pci 0000:00:00.0: BAR 0: set to [io 0x40a00000-0x40a000ff] (PCI address [0x40a00000-0x40a000ff]
<4>bio: create slab <bio-0> at 0
<6>vgaarb: loaded
<6>usbcore: registered new interface driver usbfs
<6>usbcore: registered new interface driver hub
<6>usbcore: registered new device driver usb
<6>cfg80211: Calling CRDA to update world regulatory domain
<6>Switching to clocksource timer1
<6>usbcore: registered new interface driver huawei_ether
<6>NET: Registered protocol family 2
<6>IP route cache hash table entries: 128 (order: -3, 512 bytes)
<6>TCP established hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP bind hash table entries: 16384 (order: 5, 131072 bytes)
<6>TCP: Hash tables configured (established 16384 bind 16384)
<6>TCP reno registered
<6>UDP hash table entries: 256 (order: 1, 8192 bytes)
<6>UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)
<6>NET: Registered protocol family 1
<6>RPC: Registered udp transport module.
<6>RPC: Registered tcp transport module.
<6>RPC: Registered tcp NFSv4.1 backchannel transport module.
<7>PCI: CLS 32 bytes, default 32
<6>squashfs: version 4.0 (2009/01/31) Phillip Lougher
<6>JFFS2 version 2.2. © 2001-2006 Red Hat, Inc.
<6>msgmni has been set to 979
<6>io scheduler noop registered
<6>io scheduler deadline registered
<6>io scheduler cfq registered (default)
<6>brd: module loaded
<3>mtdoops: mtd device (mtddev=name/number) must be supplied
<4>Spi id table Version 1.22
<4>Special nand id table Version 1.33
<4>Hisilicon Nand Flash Controller V301 Device Driver, Version 1.10
<4>Nand ID: 0x2C 0xDA 0x90 0x95 0x06 0x00 0x00 0x00
<4>Nand(Hardware): Block:128KB Page:2KB Chip:2GB OOB:64B ECC:4Bytes
<6>NAND device: Manufacturer ID: 0x2c, Chip ID: 0xda (Micron MT29F2G08ABA)
<4>NAND_ECC_NONE selected by board driver. This is not recommended !!
<5>3 cmdlinepart partitions found on MTD device hinand
<5>Creating 3 MTD partitions on "hinand":
<5>0x000000000000-0x000000100000 : "startcode"
<5>0x000000100000-0x000010000000 : "ubifs"
<5>0x000010000000-0x000080000000 : "reserved"
<5>UBI: attaching mtd1 to ubi0
<5>UBI: physical eraseblock size: 131072 bytes (128 KiB)
<5>UBI: logical eraseblock size: 126976 bytes
<5>UBI: smallest flash I/O unit: 2048
<5>UBI: VID header offset: 2048 (aligned 2048)
<5>UBI: data offset: 4096
<5>UBI: attached mtd1 to ubi0
<5>UBI: MTD device name: "ubifs"
<5>UBI: MTD device size: 255 MiB
<5>UBI: number of good PEBs: 2040
<5>UBI: number of bad PEBs: 0
<5>UBI: max. allowed volumes: 128
<5>UBI: wear-leveling threshold: 512
<5>UBI: number of internal volumes: 1
<5>UBI: number of user volumes: 15
<5>UBI: available PEBs: 36
<5>UBI: total number of reserved PEBs: 2004
<5>UBI: number of PEBs reserved for bad PEB handling: 40
<5>UBI: max/mean erase counter: 2/1
<5>UBI: image sequence number: 307147133
<5>UBI: background thread "ubi_bgt0d" started, PID 35
<6>PPP generic driver version 2.4.2
<6>PPP Deflate Compression module registered
<6>PPP BSD Compression module registered
<6>PPP MPPE Compression module registered
<6>NET: Registered protocol family 24
<6>SLIP: version 0.8.4-NET3.019-NEWTTY (dynamic channels, max=256) (6 bit encapsulation enabled).
<6>CSLIP: code copyright 1989 Regents of the University of California.
<6>SLIP linefill/keepalive option.
<6>usbcore: registered new interface driver asix
<6>usbcore: registered new interface driver cdc_ether
<6>usbcore: registered new interface driver net1080
<6>usbcore: registered new interface driver cdc_subset
<6>usbcore: registered new interface driver zaurus
<6>cdc_ncm: 23-Apr-2011
<6>usbcore: registered new interface driver cdc_ncm
<6>ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
<4>hiusb_start_hcd sucessful(5115)!
<6>hiusb-ehci hiusb-ehci.0: HIUSB EHCI
<6>hiusb-ehci hiusb-ehci.0: new USB bus registered, assigned bus number 1
<6>hiusb-ehci hiusb-ehci.0: irq 71, io mem 0x10a40000
<6>hiusb-ehci hiusb-ehci.0: USB 0.0 started, EHCI 1.00
<6>hub 1-0:1.0: USB hub found
<6>hub 1-0:1.0: 2 ports detected
<6>ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
<6>hiusb-ohci hiusb-ohci.0: HIUSB OHCI
<6>hiusb-ohci hiusb-ohci.0: new USB bus registered, assigned bus number 2
<6>hiusb-ohci hiusb-ohci.0: irq 70, io mem 0x10a50000
<6>hub 2-0:1.0: USB hub found
<6>hub 2-0:1.0: 2 ports detected
<4>Netfilter messages via NETLINK v0.30.
<6>ip_tables: (C) 2000-2006 Netfilter Core Team
<6>arp_tables: (C) 2002 David S. Miller
<6>TCP cubic registered
<6>NET: Registered protocol family 17
<4>VFS: Mounted root (squashfs filesystem) readonly on device 31:11.
<6>Freeing init memory: 144K
<6>usb 1-2: new high speed USB device using hiusb-ehci and address 2
<4>nf_conntrack version 0.5.0 (7836 buckets, 31344 max)
<4>CONFIG_NF_CT_ACCT is deprecated and will be removed soon. Please use
<4>nf_conntrack.acct=1 kernel parameter, acct=1 nf_conntrack module option or
<4>sysctl net.netfilter.nf_conntrack_acct=1 to enable it.
<4>hw_ssp_basic: module license 'Huawei Tech. Co., Ltd.' taints kernel.
<4>Disabling lock debugging due to kernel taint
<4>set log file to:/var/init_debug.txt
<4>hw_dm_init successfully...
<4>Soc himem config loaded[51152] /etc/wap/wap_ssp_basic.cfg
<4>Lastword meminfo:0x80802000;0x000fe000;1;
<3>current lastword info:Add=0xdfb0b000;max_num=300;Add1=0xdfb01000;Add2=0xdfb06000;Add3=0xdfb0b000;
<1>Set kmsgread process pid to:113;
<5>UBIFS: recovery needed
<3>UBIFS error (pid 121): mount_ubifs: fenghe.linux4.3 : space_fixup = 0
<5>UBIFS: recovery completed
<5>UBIFS: mounted UBI device 0, volume 13, name "file_system"
<5>UBIFS: file system size: 19681280 bytes (19220 KiB, 18 MiB, 155 LEBs)
<5>UBIFS: journal size: 9023488 bytes (8812 KiB, 8 MiB, 72 LEBs)
<5>UBIFS: media format: w4/r0 (latest is w4/r0)
<5>UBIFS: default compressor: lzo
<5>UBIFS: reserved for root: 0 bytes (0 KiB)
<5>UBIFS: recovery needed
<3>UBIFS error (pid 124): mount_ubifs: fenghe.linux4.3 : space_fixup = 0
<5>UBIFS: recovery completed
<5>UBIFS: mounted UBI device 0, volume 14, name "app"
<5>UBIFS: file system size: 133070848 bytes (129952 KiB, 126 MiB, 1048 LEBs)
<5>UBIFS: journal size: 6602752 bytes (6448 KiB, 6 MiB, 52 LEBs)
<5>UBIFS: media format: w4/r0 (latest is w4/r0)
<5>UBIFS: default compressor: lzo
<5>UBIFS: reserved for root: 4952683 bytes (4836 KiB)
<4>reload log OK!
<4>inet6_init********************************************
<6>NET: Registered protocol family 10
<6>lo: Disabled Privacy Extensions
<6>IPv6 over IPv4 tunneling driver
<6>sit0: Disabled Privacy Extensions
<4>
<4> SYSCTL module is installed
<4>
<4> PIE module is installed
<4>
<4> GPIO module is installed
<3>hi_gpio: exports duplicate symbol hi_kernel_gpio_bit_write (owned by hi_gpio_5115)
<4>
<4> I2C module is installed
<4>
<4> TIMER module is installed
<4>
<4> SPI module is installed
<4>
<4> HW module is installed
<4>
<4> UART module is installed
<4>
<4> BRIDGE module is installed
<3>hi_bridge: exports duplicate symbol hi_kernel_dp_indirect_table_op_check (owned by hi_bridge_5115)
<4>
<4> GPON module is installed
<4>
<4> EPON module is installed
<4>
<4> L3 module is installed
<4>hi_l3: Unknown symbol hi_kernel_dp_tag_profile_alloc
<4>hi_l3: Unknown symbol hi_kernel_dp_tag_profile_get
<4>hi_l3: Unknown symbol hi_kernel_dp_tag_profile_free
<4>
<4> OAM module is installed
<4>
<4> SCI module is installed
<4>
<4> hi_adp_cnt module is installed
<4>COMMON For LDSP Install Successfully...
<4>GPIO For LDSP Install Successfully...
<4>HIGHWAY For LDSP Install Successfully...
<4>
<4> ------ SOC is 5115 T PILOT ------
<4><ldsp>board version is 15
<4><ldsp>pcb version is 1
<4><ldsp>orig board version is 15
<4>CHIPADP-SD5115 BASIC For LDSP Install Successfully...
<4>CHIPADP-SD5115 EXT For LDSP Install Successfully...
<4>I2C For LDSP Install Successfully...
<4>LSW L2 For LDSP Install Successfully...
<4>LSW L3 For LDSP Install Successfully...
<4>DEV For LDSP Install Successfully...
<4>WIFI For LDSP Install Successfully...
<4>[DM]:board_ver=15,pcb_ver=1
<4>hw_dm_init_data successfully...
<4> ac_typeword_key [] ,ac_tmp_typeword_key []
<4> SPI For LDSP Install Successfully...
<4>UART For LDSP Install Successfully...
<4>BATTERY For LDSP Install Successfully...
<4>OPTIC For LDSP Install Successfully...
<4>PLOAM For LDSP Install Successfully...
<4>GMAC For LDSP Install Successfully...
<4>KEY For LDSP Install Successfully...
<4>LED For LDSP Install Successfully...
<4>RF For LDSP Install Successfully...
<4>SIM For LDSP Install Successfully...
<4>NFC For LDSP Install Successfully...
<4>CODEC For LDSP Install Successfully...
<4>SI32176 For LDSP install successfully...
<6>fuse init (API version 7.13)
<5>SCSI subsystem initialized
<6>Initializing USB Mass Storage driver...
<6>scsi0 : usb-storage 1-2:1.0
<6>usbcore: registered new interface driver usb-storage
<6>USB Mass Storage support registered.
<6>usbcore: registered new interface driver usblp
<6>usbcore: registered new interface driver cdc_acm
<6>cdc_acm: v0.26:USB Abstract Control Model driver for USB modems and ISDN adapters
<6>usbcore: registered new interface driver usbserial
<6>USB Serial support registered for generic
<6>usbcore: registered new interface driver usbserial_generic
<6>usbserial: USB Serial Driver core
<6>USB Serial support registered for pl2303
<6>usbcore: registered new interface driver pl2303
<6>pl2303: Prolific PL2303 USB to serial adaptor driver
<6>USB Serial support registered for cp210x
<6>usbcore: registered new interface driver cp210x
<6>cp210x: v0.09:Silicon Labs CP210x RS232 serial adaptor driver
<6>USB Serial support registered for FTDI USB Serial Device
<6>usbcore: registered new interface driver ftdi_sio
<6>ftdi_sio: v1.5.0:USB FTDI Serial Converters Driver
<6>usbcore: registered new interface driver usbhid
<6>usbhid: USB HID core driver
<4>USB For LDSP Install Successfully...
<4>SD For LDSP Install Successfully...
<4>hw_ker_pdt_usb_init successfully...
<4> ptp_drv_init() !! chip: 6
<4>PTP For BBSP Install Successfully...
<5>scsi 0:0:0:0: Direct-Access SanDisk Extreme 0001 PQ: 0 ANSI: 6
<3><2351>usb storge probe notify
<4>[kernel]Enter hw_ker_usbstorage_action
<4>
<4> dhcp_module_init load success !
<4>
<4> pppoe_module_init load success !
<4>l2base For BBSP Install Successfully...
<5>sd 0:0:0:0: [sda] 125045424 512-byte logical blocks: (64.0 GB/59.6 GiB)
<5>sd 0:0:0:0: [sda] Write Protect is off
<7>sd 0:0:0:0: [sda] Mode Sense: 53 00 00 08
<3>sd 0:0:0:0: [sda] Assuming drive cache: write through
<3>sd 0:0:0:0: [sda] Assuming drive cache: write through
<6> sda: sda1
<3>sd 0:0:0:0: [sda] Assuming drive cache: write through
<5>sd 0:0:0:0: [sda] Attached SCSI removable disk
<4>
<4>[ker_L2M_CTP] for bbsp Install Successfully...
<4>EMAC For LDSP Install Successfully...
<4>MPCP For LDSP Install Successfully...
<4>linux kernel dopra is installed!
<4>
<4> dsp sdk insmod success!
<4>DSP For VOICE Install Successfully...
<4>l2ext For BBSP Install Successfully...
<4>
<4> vlanflt_module_init load success !
<4>l3base for bbsp Install Successfully...
<6>GRE over IPv4 tunneling driver
<4>arp_config_bridge_filter:
<4>
<4> hw_arp_announce_module_init load success !
<4>
<4> arp_module_init load success !
<4>hw_route_ipv4_module_init in
<4>Route ipv4 for bbsp Install Successfully...
<4>Neighbour discovery for bbsp Install Successfully...
<4>Portal For BBSP Install Successfully...
<4>User device for bbsp Install Successfully...
<4>BBSP_FT_FIREWALL_FLOW_LOG close!!
<4>l3ext for bbsp Install Successfully...
<4>
<4> install success
<6>ip6_tables: (C) 2000-2006 Netfilter Core Team
<6>ip6tnl0: Disabled Privacy Extensions
<4>hw_route_ipv6_module_init in
<4>Route ipv6 for bbsp Install Successfully
<4>
<4>[ker_ROUTE_ADPT] for bbsp Install Successfully...
<4>PK v1.0 acc init
<4>[hw_ker_ipfilter_set_mode][100] mode=1 ret = 0x0
<4>ip filter install st=0x0
<6>L2TP core driver, V2.0
<6>PPPoL2TP kernel driver, V2.0
<4>
<4>[ker_pdt_wifi] for bbsp Install Successfully...
<4><LDSP> system has slave space for bob
<4>read data is over time
<4>
SD511X test self OK
<4>Optic test self ERROR
<4>WIFI test self OK
<4>PHY[1] test self OK
<4>PHY[2] test self OK
<4>PHY[3] test self OK
<4>PHY[4] test self OK
<4>
<4><LDSP> 5171 optic
<4>FILE = /usr1/code/ICP_SMARTONT_V300R015C10/code/current/ONT_Code/CI/Make/../../Source/ldsp/driver/optic/hw_ker_drv_optic.c
<4>LINE = 5469, FUNC = hw_drv_optic_cal_sw_ver_set
<4><LDSP> read cal version file error
<4>
<4><LDSP> bob optic was calibrated
<4><LDSP> optic firmware load success!
<6>GPON init success !
sd_block_regsiter((hw_sd_block_callback_t)hw_drv_sd_state_report
<4>NFC INIT*********
<3>ubi_open_volume error with 2, try UBI_READONLY;
<3>ubi_open_volume error with 2, try UBI_READONLY;
<3>FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
<3>ubi_open_volume error with 2, try UBI_READONLY;
<3>ubi_open_volume error with 2, try UBI_READONLY;
<6>warning: process `bbsp' used the deprecated sysctl system call with 3.12.16.-2.1.0.
<6>warning: process `bbsp' used the deprecated sysctl system call with 3.12.16.-2.5.0.
<6>warning: process `bbsp' used the deprecated sysctl system call with 3.12.16.-2.6.0.
<4>
<4> Alloc uiSize[1048576] uiLoop1[2]
<4> OS-Functions are registered !CPU-TYPE=3
<4> HIAPI_ZspBootCompleteWait: Boot Complete!
<4>
<4>SI32176(1) INIT SUCCESS!
<3>ubi_open_volume error with 2, try UBI_READONLY;
<3>ubi_open_volume error with 2, try UBI_READONLY;
<3>FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
<4>
<4>The link of ETH3 is up, uni_phy
<4>Init Access Mode To GPON .................[PLOAM]ONUID(0): O1 => O1
<4>[PLOAM]ONUID(0): O1 => O2
<4>[PLOAM]ONUID(0): O2 => O3
<4>[PLOAM]ONUID(24): O3 => O4
<4>[PLOAM]ONUID(24): O4 => O5
<4> wifi para select A
<4>Realtek WLAN driver - version 3.1 (2014-06-26)
<4> wlan_index:0 1, 74,0x0,0x0,0
<4>rtl8192cd_init_pci in!!!!!!!
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>Load calibration data from 0@/dev/mtdblock13
<4>Load calibration data success
<4>PCI: enabling device 0000:00:00.0 (0140 -> 0143)
<4>vendor_id=0x10EC, device_id=0x818B
<4>version_id=VERSION_8192E found
<4>HalAssociateNic OK
<4>StopHW Succeed
<6>wlan0: PCI cache line size set incorrectly (0 bytes) by BIOS/FW, correcting to 32
<4>page_ptr=d9a01000, size=228672, ring_dma_addr:9a801000, alloc_dma_buf:d9a00000, ring_virt_addr:d9a01000
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>=====>>INSIDE rtl8192cd_init_one <<=====
<4>=====>>EXIT rtl8192cd_init_one <<=====
<4>pci_register_driver() OK!(0)
<4>set log file to:/var/console.log
<1>Set kmsgread process pid to:1568;
<6>java (1603): undefined instruction: pc=405d4600
<6>Code: e590c004 e15c0008 1afd7da0 e1a00000 (e7f11110)
<6>java (1652): undefined instruction: pc=405f2940
<6>Code: e590c004 e15c0008 1afd04d0 e1a00000 (e7f11110)
<6>java (1767): undefined instruction: pc=40710670
<6>Code: 00016008 60096000 00000000 00000000 (e7f11110)
<6>java (1767): undefined instruction: pc=40710670
<6>Code: 00016008 60096000 00000000 00000000 (e7f11110)
<1>Set kmsgread process pid to:2051;
<1>Set kmsgread process pid to:2195;
<1>Set kmsgread process pid to:2378;
success!
WAP>

复制代码

setttt · 发表于 2016-3-15 00:42:30

本帖最后由 setttt 于 2016-3-15 00:45 编辑

华为sa1456c(可改Gp/Ep双模) 贝尔E-140W-P(EP) 、中兴F450G (EP)、中兴F650G(GP)四款悦ME 光猫硬件配置要求全是一样的，除华为用自家的CPU，其他三个一样，但华为、贝尔固件可以，中兴的不用考虑了，这4个光猫我全有！中兴的我送给朋友用了！

xxcat · 发表于 2016-3-15 01:05:58

setttt 发表于 2016-3-15 00:42
华为sa1456c(可改Gp/Ep双模) 贝尔E-140W-P(EP) 、中兴F450G (EP)、中兴F650G(GP)四款悦ME 光猫硬件配置要求 ...

请问中兴F650G(GP)哪里可以买到？我这里只能用GPON光猫，所以贝尔的就无缘了。。

不知道什么好 · 发表于 2016-3-15 01:52:53

5115T和不带T的5115是不同的吧

hotpop · 发表于 2016-3-15 02:01:31

MT29F2G08ABA，这个是2Gb也就是256MB的flash，不是楼主说的是2GB，只开了256MB，楼主B和b的概念还没搞清楚。。。
这机子用的螃蟹的8192还是在节约成本，就这点不太爽。。。无线性能比较弱，螃蟹芯片最大的硬伤是性能，在带机量、转发性能上存在劣势。但螃蟹芯片最大的优势是性价比。

setttt · 发表于 2016-3-15 03:34:31

本帖最后由 setttt 于 2016-3-15 03:37 编辑

setttt 发表于 2016-3-15 00:42
华为sa1456c(可改Gp/Ep双模) 贝尔E-140W-P(EP) 、中兴F450G (EP)、中兴F650G(GP)四款悦ME 光猫硬件配置要求 ...

华为sa1456c (GP)某宝有售，可改双模；中兴F650G(GP)六台已卖光暂时断货！

setttt · 发表于 2016-3-15 03:42:15

hotpop 发表于 2016-3-15 02:01
MT29F2G08ABA，这个是2Gb也就是256MB的flash，不是楼主说的是2GB，只开了256MB，楼主B和b的概念还没搞清楚 ...

用的HG8145C 的模板，就改了个千兆！

irc163 · 发表于 2016-3-15 11:46:44

其实就相当于HG8145H，无线芯片改螃蟹缩水了，增加了一个USB和SD卡槽，在CPU和NAT性能上没有提升。

xxcat · 发表于 2016-3-15 15:51:59

hotpop 发表于 2016-3-15 02:01
MT29F2G08ABA，这个是2Gb也就是256MB的flash，不是楼主说的是2GB，只开了256MB，楼主B和b的概念还没搞清楚 ...

<4>Nand(Hardware): Block:128KB Page:2KB Chip:2GB OOB:64B ECC:4Bytes
朋友请仔细看看，或者你去查查datasheet。
dev: size erasesize name
mtd0: 00100000 00020000 "startcode"
mtd1: 0ff00000 00020000 "ubifs"
mtd2: 70000000 00020000 "reserved"
mtd3: 0009b000 0001f000 "ubootA"
mtd4: 0009b000 0001f000 "ubootB"
mtd5: 0003e000 0001f000 "flash_configA"
mtd6: 0003e000 0001f000 "flash_configB"
mtd7: 0003e000 0001f000 "slave_paramA"
mtd8: 0003e000 0001f000 "slave_paramB"
mtd9: 00307000 0001f000 "kernelA"
mtd10: 00307000 0001f000 "kernelB"
mtd11: 02815000 0001f000 "rootfsA"
mtd12: 02815000 0001f000 "rootfsB"
mtd13: 0003e000 0001f000 "wifi_paramA"
mtd14: 0003e000 0001f000 "wifi_paramB"
mtd15: 0003e000 0001f000 "system_param"
mtd16: 0141a000 0001f000 "file_system"
mtd17: 0801e000 0001f000 "app"
你仔细看看保留区

xxcat · 发表于 2016-3-15 15:59:43

setttt 发表于 2016-3-15 03:42
用的HG8145C 的模板，就改了个千兆！

刚查了下datasheet
– Plane size: 2 planes x 1024 blocks per plane
– Device size: 2Gb: 2048 blocks
确实是2Gbit，不好意思我搞错，被bootlog的2GB误导了。

账号		自动登录	找回密码
密码			注册