|
现在的情况是 cfe能进 网线插1-3口 电脑网卡打红叉等于没有连接网线 LAN灯有规律的闪 用SecureCRT 这个软件显示
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: Thu Feb 12 13:10:57 CST 2009 (root@localhost.localdomain)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]
AuxFS[126,0xbefc0000] Misc[126,0xbefc0000] PSI[127,0xbefe0000]
Flash RootFS Partition Length: 16384000
CFE using EMAC 0
Auto-negotiation timed-out
10 MB Half-Duplex (assumed)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE: 0x80401000 - 0x805285D0 (1209808)
Initialized Data: 0x8041E210 - 0x8041FDF0 (7136)
BSS Area: 0x8041FDF0 - 0x804265D0 (26592)
Local Heap: 0x804265D0 - 0x805265D0 (1048576)
Stack Area: 0x805265D0 - 0x805285D0 (8192)
Text (code) segment: 0x80401000 - 0x8041E210 (119312)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.159
Gateway IP address :
Run from flash/host (f/h) : h
Default host run file name : 308nfs6358
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Board Id (0-2) : 96358VW2
Number of MAC Addresses (1-32) : 10
Base MAC Address : 00:10:18:00:00:00
PSI Size (1-64) KBytes : 24
Flash Block Size (1-128) in KBytes: 64
Auxillary File System Size Percent: 0
Main Thread Number [0|1] : 0
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x80010000
Decompression OK!
Entry at 0x80010000
Closing network.
Starting program at 0x80010000
[ 0.000000] Linux version 3.10.44 (simon@GekecServer) (gcc version 4.8.3 (OpenWrt/Linaro GCC 4.8-2014.04 r41302) ) #3 Tue Jul 1 14:56:33 CST 2014
[ 0.000000] Detected Broadcom 0x6358 CPU revision a1
[ 0.000000] CPU frequency is 300 MHz
[ 0.000000] 32MB of RAM installed
[ 0.000000] registering 40 GPIOs
[ 0.000000] board_bcm963xx: Boot address 0xbe000000
[ 0.000000] board_bcm963xx: CFE version: 1.0.37-10.3
[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected 22459976, got 7ec47774)
[ 0.000000] bootconsole [early0] enabled
[ 0.000000] CPU revision is: 0002a010 (Broadcom BMIPS4350)
[ 0.000000] board: board name: 96358VW2
[ 0.000000] Determined physical RAM map:
[ 0.000000] memory: 02000000 @ 00000000 (usable)
[ 0.000000] Initrd not found or empty - disabling initrd
[ 0.000000] Zone ranges:
[ 0.000000] Normal [mem 0x00000000-0x01ffffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x00000000-0x01ffffff]
[ 0.000000] Primary instruction cache 32kB, VIPT, 2-way, linesize 16 bytes.
[ 0.000000] Primary data cache 16kB, 2-way, VIPT, cache aliases, linesize 16 bytes
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 8128
[ 0.000000] Kernel command line: root=/dev/mtdblock2 rootfstype=squashfs,jffs2 noinitrd console=ttyS0,115200
[ 0.000000] PID hash table entries: 128 (order: -3, 512 bytes)
[ 0.000000] Dentry cache hash table entries: 4096 (order: 2, 16384 bytes)
[ 0.000000] Inode-cache hash table entries: 2048 (order: 1, 8192 bytes)
[ 0.000000] Memory: 28624k/32768k available (2506k kernel code, 4144k reserved, 726k data, 284k init, 0k highmem)
[ 0.000000] NR_IRQS:256
[ 0.000000] Calibrating delay loop... 299.26 BogoMIPS (lpj=598528)
[ 0.036000] pid_max: default: 32768 minimum: 301
[ 0.040000] Mount-cache hash table entries: 512
[ 0.048000] NET: Registered protocol family 16
[ 0.064000] registering PCI controller with io_map_base unset
[ 0.068000] registering PCI controller with io_map_base unset
[ 0.088000] bio: create slab <bio-0> at 0
[ 0.096000] PCI host bridge to bus 0000:00
[ 0.100000] pci_bus 0000:00: root bus resource [mem 0x30000000-0x37ffffff]
[ 0.104000] pci_bus 0000:00: root bus resource [io 0x8000000-0x8007fff]
[ 0.108000] pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]
[ 0.124000] pci 0000:00:01.0: BAR 0: assigned [mem 0x30000000-0x30001fff]
[ 0.128000] PCI host bridge to bus 0000:01
[ 0.132000] pci_bus 0000:01: root bus resource [mem 0x38000000-0x3fffffff]
[ 0.136000] pci_bus 0000:01: root bus resource [io 0x8008000-0x800ffff]
[ 0.140000] pci_bus 0000:01: No busn resource found for root bus, will use [bus 01-ff]
[ 0.144000] pci 0000:01:1e.0: bridge configuration invalid ([bus 00-00]), reconfiguring
[ 0.148000] pci 0000:01:1e.0: BAR 10: assigned [mem 0x38000000-0x3fffffff]
[ 0.152000] pci 0000:01:1e.0: BAR 7: assigned [io 0x8008000-0x80080ff]
[ 0.156000] pci 0000:01:1e.0: BAR 8: assigned [io 0x8008400-0x80084ff]
[ 0.160000] pci 0000:01:1e.0: CardBus bridge to [bus 02-05]
[ 0.164000] pci 0000:01:1e.0: bridge window [io 0x8008000-0x80080ff]
[ 0.168000] pci 0000:01:1e.0: bridge window [io 0x8008400-0x80084ff]
[ 0.172000] pci 0000:01:1e.0: bridge window [mem 0x38000000-0x3fffffff]
[ 0.176000] PCI: Enabling device 0000:01:1e.0 (0000 -> 0003)
[ 0.180000] Switching to clocksource MIPS
[ 0.192000] PCI: Enabling device 0000:00:01.0 (0000 -> 0002)
[ 0.220000] ssb: Found chip with id 0x4318, rev 0x02 and package 0x00
[ 0.284000] ssb: Sonics Silicon Backplane found on PCI device 0000:00:01.0
[ 0.292000] NET: Registered protocol family 2
[ 0.300000] TCP established hash table entries: 512 (order: 0, 4096 bytes)
[ 0.308000] TCP bind hash table entries: 512 (order: -1, 2048 bytes)
[ 0.312000] TCP: Hash tables configured (established 512 bind 512)
[ 0.320000] TCP: reno registered
[ 0.324000] UDP hash table entries: 256 (order: 0, 4096 bytes)
[ 0.328000] UDP-Lite hash table entries: 256 (order: 0, 4096 bytes)
[ 0.336000] NET: Registered protocol family 1
[ 0.344000] audit: initializing netlink socket (disabled)
[ 0.352000] type=2000 audit(0.351:1): initialized
[ 0.356000] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 0.364000] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.
[ 0.372000] msgmni has been set to 55
[ 0.380000] io scheduler noop registered
[ 0.384000] io scheduler deadline registered (default)
[ 0.392000] bcm63xx_uart.0: ttyS0 at MMIO 0xfffe0100 (irq = 10) is a bcm63xx_uart
[ 0.400000] console [ttyS0] enabled, bootconsole disabled
[ 0.400000] console [ttyS0] enabled, bootconsole disabled
[ 0.416000] physmap platform flash device: 02000000 at 1e000000
[ 0.420000] physmap-flash.0: Found 1 x16 devices at 0x0 in 16-bit bank. Manufacturer ID 0x000001 Chip ID 0x002101
[ 0.432000] Amd/Fujitsu Extended Query Table at 0x0040
[ 0.436000] Amd/Fujitsu Extended Query version 1.3.
[ 0.444000] number of CFI chips: 1
[ 0.448000] bcm63xxpart: CFE boot tag found with version 6 and board type 96358VW2
[ 0.456000] bcm63xxpart: Partition 0 is CFE offset 0 and length 20000
[ 0.460000] bcm63xxpart: Partition 1 is kernel offset 20100 and length 11ff00
[ 0.468000] bcm63xxpart: Partition 2 is rootfs offset 140000 and length ea0000
[ 0.476000] bcm63xxpart: Partition 3 is nvram offset fe0000 and length 20000
[ 0.484000] bcm63xxpart: Partition 4 is linux offset 20000 and length fc0000
[ 0.492000] bcm63xxpart: Spare partition is offset 760004 and length 87fffc
[ 0.496000] 5 bcm63xxpart partitions found on MTD device physmap-flash.0
[ 0.504000] Creating 5 MTD partitions on "physmap-flash.0":
[ 0.512000] 0x000000000000-0x000000020000 : "CFE"
[ 0.520000] 0x000000020100-0x000000140000 : "kernel"
[ 0.524000] mtd: partition "kernel" must either start or end on erase block boundary or be smaller than an erase block -- forcing read-only
[ 0.540000] 0x000000140000-0x000000fe0000 : "rootfs"
[ 0.548000] mtd: device 2 (rootfs) set to be root filesystem
[ 0.556000] mtd: partition "rootfs_data" created automatically, ofs=0x760000, len=0x880000
[ 0.564000] 0x000000760000-0x000000fe0000 : "rootfs_data"
[ 0.572000] 0x000000fe0000-0x000001000000 : "nvram"
[ 0.584000] 0x000000020000-0x000000fe0000 : "linux"
[ 0.596000] bcm63xx-spi bcm63xx-spi: at 0xfffe0800 (irq 9, FIFOs size 542)
[ 0.612000] libphy: bcm63xx_enet MII bus: probed
[ 0.616000] bcm63xx_enet bcm63xx_enet.0: attached PHY at address 1 [Broadcom BCM63XX (2)]
[ 0.632000] libphy: bcm63xx_enet MII bus: probed
[ 0.640000] b53_common: found switch: BCM5325, rev 0
[ 0.644000] bcm63xx_enet bcm63xx_enet.1: attached PHY at address 0 [Broadcom B53 (1)]
[ 0.656000] bcm63xx-wdt bcm63xx-wdt: started, timer margin: 30 sec
[ 0.672000] TCP: cubic registered
[ 0.676000] NET: Registered protocol family 17
[ 0.680000] Bridge firewalling registered
[ 0.684000] 8021q: 802.1Q VLAN Support v1.8
[ 0.704000] VFS: Mounted root (squashfs filesystem) readonly on device 31:2.
[ 0.716000] Freeing unused kernel memory: 284K (80339000 - 80380000)
procd: Console is alive
procd: - watchdog -
[ 5.612000] usbcore: registered new interface driver usbfs
[ 5.620000] usbcore: registered new interface driver hub
[ 5.628000] usbcore: registered new device driver usb
[ 5.640000] Button Hotplug driver version 0.4.1
[ 5.740000] SCSI subsystem initialized
[ 5.756000] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 5.768000] ehci-platform: EHCI generic platform driver
[ 5.772000] ehci-platform ehci-platform: EHCI Host Controller
[ 5.780000] ehci-platform ehci-platform: new USB bus registered, assigned bus number 1
[ 5.788000] ehci-platform ehci-platform: irq 18, io mem 0xfffe1300
[ 5.804000] ehci-platform ehci-platform: USB 2.0 started, EHCI 1.00, overcurrent ignored
[ 5.812000] hub 1-0:1.0: USB hub found
[ 5.816000] hub 1-0:1.0: 2 ports detected
[ 5.828000] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 5.836000] ohci-platform ohci-platform: Generic Platform OHCI Controller
[ 5.840000] ohci-platform ohci-platform: new USB bus registered, assigned bus number 2
[ 5.848000] ohci-platform ohci-platform: irq 13, io mem 0xfffe1400
[ 5.916000] hub 2-0:1.0: USB hub found
[ 5.920000] hub 2-0:1.0: 2 ports detected
[ 5.932000] uhci_hcd: USB Universal Host Controller Interface driver
[ 5.952000] usbcore: registered new interface driver usb-storage
[ 5.960000] input: gpio-keys-polled as /devices/platform/gpio-keys-polled.0/input/input0
procd: - preinit -
ifconfig: SIOCGIFFLAGS: No such device
Press the [f] key and hit [enter] to enter failsafe mode
Press the [1], [2], [3] or [4] key and hit [enter] to select the debug level
kmod: ran 1 iterations
[ 11.172000] jffs2: notice: (255) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 18 of xref (0 dead, 2 orphan) found.
block: extroot: no root or overlay mount defined
jffs2 is ready
jffs2 is ready
[ 11.244000] jffs2: notice: (252) jffs2_build_xattr_subsystem: complete building xattr subsystem, 1 of xdatum (0 unchecked, 0 orphan) and 18 of xref (0 dead, 2 orphan) found.
switching to overlay
ifconfig: SIOCGIFFLAGS: No such device
procd: - early -
procd: - watchdog -
procd: - ubus -
procd: - init -
Please press Enter to activate this console.
[ 27.308000] NET: Registered protocol family 10
[ 27.356000] NTFS driver 2.1.30 [Flags: R/O MODULE].
[ 27.380000] tun: Universal TUN/TAP device driver, 1.6
[ 27.388000] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 27.408000] sit: IPv6 over IPv4 tunneling driver
[ 27.440000] gre: GRE over IPv4 demultiplexor driver
[ 27.452000] ip_gre: GRE over IPv4 tunneling driver
[ 27.508000] nf_conntrack version 0.5.0 (451 buckets, 1804 max)
[ 27.540000] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 27.616000] u32 classifier
[ 27.620000] input device check on
[ 27.624000] Actions configured
[ 27.836000] Mirror/redirect action on
[ 28.036000] Loading modules backported from Linux version master-2014-05-22-0-gf2032ea
[ 28.044000] Backport generated by backports.git backports-20140320-37-g5c33da0
[ 28.060000] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 28.212000] xt_time: kernel timezone is -0000
[ 28.340000] cfg80211: Calling CRDA to update world regulatory domain
[ 28.356000] cfg80211: World regulatory domain updated:
[ 28.364000] cfg80211: DFS Master region: unset
[ 28.368000] cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp), (dfs_cac_time)
[ 28.376000] cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 28.384000] cfg80211: (2457000 KHz - 2482000 KHz @ 40000 KHz), (N/A, 2000 mBm), (N/A)
[ 28.392000] cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (N/A, 2000 mBm), (N/A)
[ 28.404000] cfg80211: (5170000 KHz - 5250000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 28.412000] cfg80211: (5735000 KHz - 5835000 KHz @ 80000 KHz), (N/A, 2000 mBm), (N/A)
[ 28.420000] cfg80211: (57240000 KHz - 63720000 KHz @ 2160000 KHz), (N/A, 0 mBm), (N/A)
[ 28.736000] PPP generic driver version 2.4.2
[ 28.768000] PPP MPPE Compression module registered
[ 28.808000] NET: Registered protocol family 24
[ 28.824000] PPTP driver version 0.8.5
[ 28.992000] usbcore: registered new interface driver rtl8187
[ 29.256000] b43-phy0: Broadcom 4318 WLAN found (core revision 9)
[ 29.296000] b43-phy0: Found PHY: Analog 3, Type 2 (G), Revision 7
[ 29.300000] b43-phy0 warning: 5 GHz band is unsupported on this PHY
[ 29.504000] Broadcom 43xx driver loaded [ Features: PNL ]
[ 29.684000] usbcore: registered new interface driver rt2800usb
[ 29.852000] usbcore: registered new interface driver rtl8192cu
[ 43.608000] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 44.844000] eth1: link UP - 100/full - flow control off
[ 45.336000] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready
[ 54.428000] device eth1 entered promiscuous mode
[ 54.436000] br-lan: port 1(eth1) entered forwarding state
[ 54.440000] br-lan: port 1(eth1) entered forwarding state
[ 54.476000] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 56.144000] eth1: link UP - 100/full - flow control off
[ 56.444000] br-lan: port 1(eth1) entered forwarding state
procd: - init complete -
电脑是WIN7 64位的 大亚db120-wg双usb版
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册
×
|