本帖最后由 铁拳 于 2015-7-9 21:59 编辑
) d3 T' m/ c+ c+ Q
/ n$ \: @& G% p5 r8 w' t烽火 AN5006-02-A EPON 光猫，不带 WiFi，也不带语音，用 CFE -i 将猫里原有的数据清掉了，之后启动时加载快结束时会死机，反复折腾，最终 mount -w 将 realrootfs 挂载后，编辑过程中死机，导至 CRC Wrong 以及部份内容丢失，网上没找到厂商的 rom，请各位大师帮忙分析一下看看有没有可以替代的固件，谢谢！
, `2 m9 u5 P7 a$ u8 X0 A3 {7 P1 C
HELO CPUI L1CI PLLI PMCB HELO CPUI L1CI 4.1403-1.0.38-117.80 DRAM ---- PHYS ZQDN PHYE DINT TST1 TST2 PASS ---- ZBSS MAIN ENTR SP01 SP02 FPS0 NAN7 BT00 0001 NAN7 BT00 0001 NAN3 RFS1 NAN5 PASS Base:4.14_03 CFEversion 1.0.38-117.80 for BCM96838 (32bit,SP,BE) Copyright(C) 2000-2013 Broadcom Corporation. ChipID: BCM68385_B0, MIPS: 240MHz, DDR: 333MHz, Bus: 240MHz RDP:400MHz MainThread: TP0 TotalMemory: 134217728 bytes (128MB) BootAddress: 0xbfc00000 NANDflash device: name Spansion S34ML01G1, id 0x01f1 block 128KB size 131072KB ddr_tm_base_address= 0xa0800000 BoardIP address :192.168.1.1:ffffff00 HostIP address : 192.168.1.100 GatewayIP address : Runfrom flash/host/tftp (f/h/c) : f Defaulthost run file name : vmlinux Defaulthost flash file name :bcm963xx_fs_kernel Bootdelay (0-9 seconds) : 1 Defaulthost ramdisk file name : Defaultramdisk store address : BoardId (0-35) :968385PVSFUEPON Numberof MAC Addresses (1-32) : 11 BaseMAC Address :xx:xx:xx:xx:xx:xx PSISize (1-128) KBytes : 128 EnableBackup PSI [0|1] : 1 SystemLog Size (0-256) KBytes : 64 FlashBlock Size (1-128) in KBytes: 128 AuxillaryFile System Size Percent: 0 MainThread Number [0|1] : 0 ProductcodeClass : 0x00010015 ProductcodeHwInfo : 0x08800000 ProductcodePortMap : 0x00000000 ProductcodeExtend : 0x00000000 GPONSerial Number :"TWSHXXXXXXXX" GPONPassword :" " CTGPON LOID : "" CTGPON Password :"" MCmemory allocation (MB) : 0 TMmemory allocation (MB) : 0 VoiceBoard Configuration (0-0) : LE9540 ProductClass : AN5006-02-A WlSsid : WlKey : UserPass : xxxxx DeviceId : XXXXXXXXXXXXXXXXX FactorycfgFlg : 0 CreatingCPU ring for queue number 0 with 32 packets descriptor=0x8066c810 Done initializing Ring 0 Base=0xa220f730KEnd=0xa220f930K calculated entries= 32 RDD Base=0x0220f730Kdescriptor=0x8066c810 OpenPHY 1 on MAC 0 : link state = Down OpenPHY 2 on MAC 1 : link state = Down ***Press any key to stop auto run (1 seconds) *** Autorun second count down: 0 BootingFrom Image (0xc3880000) ... DecompressionOK! Entryat 0x803cbb70 Closingnetwork. rdd_ring_destroy Starting program at 0x803cbb70 Linuxversion 3.4.11-rt19 (hehulin@pon.twsh.com) (gcc version 4.6.2 (Buildroot2011.11) ) #6 SMP PREEMPT Sat Mar 22 22:26:40 CST 2014 BCMFlash API. Flash device is not found. 968385PVSFUEPONprom init CPUrevision is: 0002a080 (Broadcom BMIPS4350) Determinedphysical RAM map: memory: 01400000 @ 06c00000 (reserved) memory: 00400000 @ 06800000 (reserved) memory: 06800000 @ 00000000 (usable) Initrdnot found or empty - disabling initrd ZonePFN ranges: DMA 0x00000000 -> 0x00001000 Normal 0x00001000 -> 0x00006800 Movablezone start PFN for each node Earlymemory PFN ranges 0: 0x00000000 -> 0x00006800 Onnode 0 totalpages: 26624 free_area_init_node:node 0, pgdat 804e6810, node_mem_map 81000000 DMA zone: 32 pages used for memmap DMA zone: 0 pages reserved DMA zone: 4064 pages, LIFO batch:0 Normal zone: 176 pages used for memmap Normal zone: 22352 pages, LIFO batch:3 PERCPU:Embedded 7 pages/cpu @810d3000 s5088 r8192 d15392 u32768 pcpu-alloc:s5088 r8192 d15392 u32768 alloc=8*4096 pcpu-alloc:[0] 0 [0] 1 Built1 zonelists in Zone order, mobility grouping on. Total pages: 26416 Kernelcommand line: root=mtd:ImageA rw rootfstype=jffs2 irqaffinity=0 PIDhash table entries: 512 (order: -1, 2048 bytes) Dentrycache hash table entries: 16384 (order: 4, 65536 bytes) Inode-cachehash table entries: 8192 (order: 3, 32768 bytes) Primaryinstruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primarydata cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Memory:100024k/106496k available (3879k kernel code, 6472k reserved, 1077k data, 220kinit, 0k highmem) Preemptiblehierarchical RCU implementation. NR_IRQS:256 console[ttyS0] enabled Allocatingmemory for DSP module core and initialization code AllocatedDSP module memory - CORE=0x0 SIZE=0, INIT=0x0 SIZE=0 Calibratingdelay loop... 237.05 BogoMIPS (lpj=118528) pid_max:default: 32768 minimum: 301 Mount-cachehash table entries: 512 --KernelConfig-- SMP=1 PREEMPT=1 DEBUG_SPINLOCK=0 DEBUG_MUTEXES=0 BroadcomLogger v0.1 Mar 21 2014 21:27:44 CPUrevision is: 0002a080 (Broadcom BMIPS4350) Primaryinstruction cache 64kB, VIPT, 4-way, linesize 16 bytes. Primarydata cache 32kB, 2-way, VIPT, cache aliases, linesize 16 bytes Broughtup 2 CPUs NET:Registered protocol family 16 TotalFlash size: 0K with -1 sectors registeringPCI controller with io_map_base unset bio:create slab <bio-0> at 0 SCSIsubsystem initialized usbcore:registered new interface driver usbfs usbcore:registered new interface driver hub usbcore:registered new device driver usb PCIhost bridge to bus 0000:00 pci_bus0000:00: root bus resource [mem 0xeff00000-0xefffffff] pci_bus0000:00: root bus resource [io 0xf1000000-0xf100ffff] bcmhs_spibcmhs_spi.1: master is unqueued, this is deprecated skbFreeTaskcreated successfully BLOGv3.0 Initialized BLOGRule v1.0 Initialized BroadcomIQoS v0.1 Mar 21 2014 21:35:00 initialized Switchingto clocksource MIPS NET:Registered protocol family 2 IProute cache hash table entries: 1024 (order: 0, 4096 bytes) TCPestablished hash table entries: 4096 (order: 3, 32768 bytes) TCPbind hash table entries: 4096 (order: 3, 32768 bytes) TCP:Hash tables configured (established 4096 bind 4096) TCP:reno registered UDPhash table entries: 128 (order: 0, 4096 bytes) UDP-Litehash table entries: 128 (order: 0, 4096 bytes) NET:Registered protocol family 1 PCI:CLS 0 bytes, default 16 init_bcm_tstamp:unhandled mips_hpt_freq=120000000, adjust constants in bcm_tstamp.c bcm_tstampinitialized, (hpt_freq=120000000 2us_div=120 2ns_mult=0 2ns_shift=0) squashfs:version 4.0 (2009/01/31) Phillip Lougher jffs2:version 2.2. (NAND) ? 2001-2006 Red Hat, Inc. fuseinit (API version 7.18) msgmnihas been set to 195 ioscheduler noop registered (default) brd:module loaded loop:module loaded bcm963xx_mtddriver Failedto read image tag from flash BroadcomDSL NAND controller (BrcmNand Controller) mtd->oobsize=0,mtd->eccOobSize=0 NAND_CS_NAND_XOR=00000000 B4:NandSelect=40000001, nandConfig=15162400, chipSelect=0 brcmnand_read_id:CS0: dev_id=01f1001d After:NandSelect=40000001, nandConfig=15162400 Blocksize=00020000, erase shift=17 NANDConfig: Reg=15162400, chipSize=128 MB, blockSize=128K, erase_shift=11 busWidth=1,pageSize=2048B, page_shift=11, page_mask=000007ff timing1not adjusted: 6574845b timing2not adjusted: 00001e96 BrcmNANDmfg 1 f1 SPANSION_S30ML01GP_08 128MB on CS0 FoundNAND on CS0: ACC=f7441010, cfg=15162400, flashId=01f1001d, tim1=6574845b,tim2=00001e96 BrcmNANDversion = 0x80000500 128MB @00000000 brcmnand_scan:B4 nand_select = 40000001 brcmnand_scan:After nand_select = 40000001 handle_acc_control:default CORR ERR threshold 1 bits ACC:16 OOB bytes per 512B ECC step; from ID probe: 16 page_shift=11,bbt_erase_shift=17, chip_shift=27, phys_erase_shift=17 BrcmNAND controller version = 5.0 NAND flash size 128MB @18000000 ECClayout=brcmnand_oob_bch4_2k brcmnand_scan: mtd->oobsize=64 brcmnand_scan:oobavail=35, eccsize=512, writesize=2048 brcmnand_scan,eccsize=512, writesize=2048, eccsteps=4, ecclevel=4, eccbytes=7 -->brcmnand_default_bbt brcmnand_default_bbt:bbt_td = bbt_slc_bch4_main_descr Badblock table Bbt0 found at page 0000ffc0, version 0x01 for chip on CS0 Badblock table 1tbB found at page 0000ff80, version 0x01 for chip on CS0 brcmnand_reset_corr_threshold:default CORR ERR threshold 1 bits forCS0 brcmnand_reset_corr_threshold:CORR ERR threshold changed to 3 bits for CS0 brcmnandCET:Status -> Deferred Creating8 MTD partitions on "brcmnand.0": 0x000003c80000-0x000007500000: "ImageA" 0x000007700000-0x000007a00000: "ctadmin" 0x000007a00000-0x000007e00000: "Config" 0x000007500000-0x000007600000: "Env" 0x000007600000-0x000007700000: "EnvB" 0x000000400000-0x000003c80000: "ImageB" 0x000000000000-0x000000400000: "Boot" 0x000007e00000-0x000007f00000: "SECTION_EGIS" PPPgeneric driver version 2.4.2 PPPBSD Compression module registered PPPDeflate Compression module registered NET:Registered protocol family 24 ehci_hcd:USB 2.0 'Enhanced' Host Controller (EHCI) Driver ohci_hcd:USB 1.1 'Open' Host Controller (OHCI) Driver usbcore:registered new interface driver usblp i2c/dev entries driver brcmboard:brcm_board_init entry #################EnteringboardLedInit(void)########### ###########twboard:brcm_board_init entry########### Serial:BCM63XX driver $Revision: 3.00 $ MagicSysRq enabled (type ^ h for list of supported commands) ttyS0at MMIO 0xb4e00500 (irq = 9) is a BCM63XX ttyS1at MMIO 0xb4e00520 (irq = 10) is a BCM63XX GACTprobability NOT on Mirror/redirectaction on netem:version 1.3 u32classifier input device check on Actions configured TCP:cubic registered NET:Registered protocol family 10 IPv6over IPv4 tunneling driver NET:Registered protocol family 17 InitializingMCPD Module Ebtablesv2.0 registered ebt_timeregistered ebt_ftosregistered ebt_wmm_markregistered L2TPcore driver, V2.0 PPPoL2TPkernel driver, V2.0 8021q:802.1Q VLAN Support v1.8 VFS:Mounted root (jffs2 filesystem) on device 31:0. Freeingunused kernel memory: 220k freed initstarted: BusyBox v1.17.2 (2013-09-06 14:52:42 CST) startingpid 263, tty '/dev/ttyS0': '/bin/mountfs' inquerymode BUTTON:SzBoardId is [968385PVSFUEPON] LED:SzBoardId is [968385PVSFUEPON] C1KLED driver is registered. ==============EnteringLOS Led Slow blink================== ============== Leaving LOS Led ================== jffs2:Empty flash at 0x00100828 ends at 0x00101000 jffs2:notice: (282) check_node_data: wrong data CRC in data node at 0x002c59cc: read0xcb0913ca, calculated 0x58263f20. Mountingfilesystems... Configuringsystem... mountconfig partition OK SF_SetFeatureStr:Set feature(uplink_type) to epon ACTIVEIMG=1 /usr/local/bin/update_backup_img_ver.sh:line 12: syntax error: unexpected "fi" Loadingdrivers and kernel modules... ...... | 
粤公网安备44152102000001号 
发表于 2015-7-8 13:31:57