1308h在刷完uboott悲剧了，请技术达人进一下！

aiening

问哈坛子里的兄弟伙，1308用ttl刷机的时候提示：DRAM:  128 MB
* f3 I! }2 z. J/ K; ?1 ^. W3 }*** Warning - bad CRC or NAND, using default environment
3 J5 Z" j! z2 O; X+ ]8 Din ys modify!
serial number: 13082000AC2D5EC5F
chip: hi3560EROC
mac:00:0A:C2:D5:EC:5F
' p. |2 t7 d% b, [) [7 G9 o8 I======================pre============================
upInfo->kernel_suffix = -1
4 a/ s- Q0 N; c$ M/ `# jupInfo->rootfs_suffix = -1
2 Y/ V! U$ v, `" @upInfo->bootcount = -1
" d/ }: D5 o1 ]: qupInfo->boottimes = -1
upInfo->bootok = -1
upInfo->upgrade_target =
  S4 l5 S  R2 F- ?0 ]/ n6 I======================begin============================
0 [7 [) _5 ^! r& w/ ?: o( bupInfo->kernel_suffix = -1
. q9 E1 |5 a. IupInfo->rootfs_suffix = -1
; b$ P4 L5 s. G1 O3 eupInfo->bootcount = -1
6 Q0 M' O) G4 v9 X" v3 mupInfo->boottimes = -1
upInfo->bootok = -1
upInfo->upgrade_target =
  O( S" ?9 H7 z1 X$ @======================after============================
upInfo->kernel_suffix = -1
2 a% q8 i! E# i1 yupInfo->rootfs_suffix = -1
upInfo->bootcount = -1
- k. \# H: ^; x+ u% K5 lupInfo->boottimes = -1
upInfo->bootok = -1
$ N0 A1 G& I  z& t( w  cupInfo->upgrade_target =
$ J! s# J) z9 s! c/ {In:    serial
Out:   serial
Err:   serial
1 \5 Z: Q- R) v0 i: ?MAC:   00-0A-C2-D5-EC-5F
USB:   scanning bus for devices... 1 USB Device(s) found
$ k( z5 D5 u! }6 h; FUSB:   scanning bus for devices... 1 USB Device(s) found
9 L, k& e- M& X# `9 _) KUSB:   scanning bus for devices... 1 USB Device(s) found
& C: O- T: p4 @9 X& N8 x) x. u: ^0 Storage Device(s) found
+ y: U1 \* n& y& C2 a! M7 G$ hub_before_ver=<NULL>
/ b; ~% K# k6 j" ~8 h) j2 A  D; Spreboot is = mw.b 0xc1500000 ff 0x80000;tftp 0xc1500000 ubs;nand erase 0x100000000 0x108000000;nand write 0xc1500000 0x0 0x80000;mw.b 0xc1500000 ff 0x200000;tftp 0xc1500000 5532cfg;nand write 0xc1500000 0x140000 0x60000;nand write 0xc1500000 0x1A0000 0x60000;mw.b 0xc1500000 ff 0x200000;tftp 0xc1500000 yk;nand write 0xc1500000 0x200000 0x200000;nand write 0xc1500000 0x500000 0x200000;mw.b 0xc1500000 ff 0x2800000;tftp 0xc1500000 ya;nand write.yaffs 0xc1500000 0x800000 0x27ffcc0;nand write.yaffs 0xc1500000 0x3000000 0x27ffcc0;setenv preboot 'n';update -script=5532D.uHisilicon ETH net controler
5 \! X6 T. Q$ y$ M8 x/ ?0 ]$ E我更新了uboot不小心用了reset，然后就这样了。
4 ?$ e& b8 j- f- ~; d  `我按照它的恢复脚本吧uboot、config、kernel、yaffs都恢复了，但最后要读取一个什么：
Staring update BSP ...
) T! e' M; |) s2 {[ Run  ]: setenv script 5532D.u
9 r& {9 q% C0 Y4 J" P0 hStaring download update-script '5532D.u' to 0xC00631C8 ...
请问怎么建立这个5532D.u的脚本呢？
或者我在哪搞得到这个脚本？
% m9 u/ w: U2 @, ~% x这个脚本在这里起到什么作用呢？


7 @- B. @% c0 X1 V3 s  d; G

tm5880891

上编程器吧

aiening

tm5880891 发表于 2015-3-10 01:11
上编程器吧

5 E# |% j) a8 y刷坏了的只有上编程器了，
后来找到原因了，刷好后只要reset就必定会出这个问题，
但是关机再开机就没这个问题，没搞懂原理！