求助：MX29LV640BBTC-90无法被BRJTAG2.05识别。

xjmjack

我的这个路由器是H618B 原为M29flash  现换8M为MX29LV640BBTC-90 。可是不能被识别到
有时候用C:\brjtag>brjtag -probeonly /cable:2 可以识别为/fc:107 (00C2 22CB) ........... MX29LV640EB/DB
请大侠帮忙看下是没有焊好还是什么原因
C:\brjtag>brjtag -probeonly /cable:2
        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================

  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000091999999]
Initializing J-Link HW Ver. 8.0
Set I/O speed to 3000 KHz
Detected target Vref = 0.647V
USB TAP device has been initialized. Please confirm VREF signal connected
Press any key to continue... ONCE target board is powered on!
Probing bus ... Done
Detected IR Length is 8
CPU assumed running under LITTLE endian
CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***
    - EJTAG IMPCODE ....... : 00000000000000000000000000000000 (00000000)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS32
Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
Probing Flash at Address: 0x1FC00000 ...
Detected pFlash Chip ID (VenID:DevID = 0000 : 0000)
*** Found a (8MB) CFI Compatiable Flash Chip from Unknow

*** REQUESTED OPERATION IS COMPLETE ***

C:\brjtag>brjtag -probeonly /cable:2
        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================

  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000091999999]
Initializing J-Link HW Ver. 8.0
Set I/O speed to 3000 KHz
Detected target Vref = 0.349V
USB TAP device has been initialized. Please confirm VREF signal connected
Press any key to continue... ONCE target board is powered on!
Probing bus ... Done
Detected IR Length is 8
CPU assumed running under LITTLE endian
CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***
    - EJTAG IMPCODE ....... : 00000000000000000000000000000000 (00000000)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS32
Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
Probing Flash at Address: 0x1FC00000 ...
Detected pFlash Chip ID (VenID:DevID = 0000 : 0005)
*** Found a (8MB) CFI Compatiable Flash Chip from Unknow





C:\brjtag>brjtag -probeonly /verbose /cable:2
        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================

  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000091999999]
Initializing J-Link HW Ver. 8.0
Set I/O speed to 3000 KHz
Detected target Vref = 0.0V
USB TAP device has been initialized. Please confirm VREF signal connected!
Press any key to continue... ONCE target board is powered on!
Probing bus ... Done
Detected IR Length is 8
CPU assumed running under LITTLE endian
CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***
    - EJTAG IMPCODE ....... : 00000000000000000000000000000000 (00000000)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS32
Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped
Probing Flash at Address: 0x1FC00000 ...
Read pFlash raw Chip ID (MfrID:DevID = 0000 : 0000)
Detected pFlash Chip ID (VenID:DevID = 0000 : 0000)

Read Array Starting from offset [0x0010]
Array[0x10] = 0x0051
Array[0x11] = 0x0052
Array[0x12] = 0x0059

Read Array Starting from offset [0x0010]
Array[0x10] = 0x0051
Array[0x11] = 0x0052
Array[0x12] = 0x0059
Array[0x13] = 0x0002
Array[0x14] = 0x0000
Array[0x15] = 0x0040
Array[0x16] = 0x0000
Array[0x17] = 0x0000
Array[0x18] = 0x0000
Array[0x19] = 0x0000
Array[0x1A] = 0x0000
Array[0x1B] = 0x0027
Array[0x1C] = 0x0036
Array[0x1D] = 0x0000
Array[0x1E] = 0x0000
Array[0x1F] = 0x0004
Array[0x20] = 0x0000
Array[0x21] = 0x000A
Array[0x22] = 0x0000
Array[0x23] = 0x0005
Array[0x24] = 0x0000
Array[0x25] = 0x0004
Array[0x26] = 0x0000
Array[0x27] = 0x0017
Array[0x28] = 0x0002
Array[0x29] = 0x0000
Array[0x2A] = 0x0000
Array[0x2B] = 0x0000
Array[0x2C] = 0x0002
Array[0x2D] = 0x0007
Array[0x2E] = 0x0000
Array[0x2F] = 0x0020
Array[0x30] = 0x0000
Array[0x31] = 0x007E
Array[0x32] = 0x0000
Array[0x33] = 0x0000
Array[0x34] = 0x0001
Array[0x35] = 0x0000
Array[0x36] = 0x0000
Array[0x37] = 0x0000
Array[0x38] = 0x0000
Array[0x39] = 0x0000
Array[0x3A] = 0x0000
Array[0x3B] = 0x0000
Array[0x3C] = 0x0000
Flash CommandSet = 0002

Read Array Starting from offset [0x0040]
Array[0x40] = 0x0050
Array[0x41] = 0x0052
Array[0x42] = 0x0049
Array[0x43] = 0x0031
Array[0x44] = 0x0031
Array[0x45] = 0x0000
Array[0x46] = 0x0002
Array[0x47] = 0x0004
Array[0x48] = 0x0001
Array[0x49] = 0x0004
Array[0x4A] = 0x0000
Array[0x4B] = 0x0000
Array[0x4C] = 0x0000
Array[0x4D] = 0x00B5
Array[0x4E] = 0x00C5
Array[0x4F] = 0x0002
Flash Boot Block Location: Non TOP
Flash total size: 8192KB (8MB)
Flash has total 2 erase block regions
Region[0] sector count:   8,   per size:  8KB
Region[1] sector count: 127,   per size: 64KB
Complete CFI Query!!
Matching Flash Chip (VenID:DevID = 0000 : 0000)
*** Found a (8MB) CFI Compatiable Flash Chip from Unknow

*** REQUESTED OPERATION IS COMPLETE ***

xjmjack

而且刷机的时候一直卡在 Erasing block: 1 (addr = 1C000000)...
经常会出现BRJTAG 错误关闭 我的是WIN7 系统 使用的是JLINK V8 安装了LIBUSB-WIN32 驱动


C:\brjtag>brjtag -flash:cfe /cable:2

        ===============================================
         Broadcom EJTAG Debrick Utility v2.0.5-hugebird
        ===============================================


  Open USB device: 0x1366:0101
  Vendor Name: [SEGGER]
  Produc Name: [J-Link]
  Serial No  : [000091999999]

Initializing J-Link HW Ver. 8.0
Set I/O speed to 3000 KHz
Detected target Vref = 0.556V

USB TAP device has been initialized. Please confirm VREF signal connected!
Press any key to continue... ONCE target board is powered on!

Probing bus ... Done

Detected IR Length is 8

CPU assumed running under LITTLE endian

CPU Chip ID: 00110101001101010100000101111111 (3535417F)
*** Found a Broadcom manufactured BCM5354 REV 03 CPU ***

    - EJTAG IMPCODE ....... : 00000000000000000000000000000000 (00000000)
    - EJTAG Version ....... : 1 or 2.0
    - EJTAG DMA Support ... : Yes
    - EJTAG Implementation flags: R4k MIPS32

Issuing Processor / Peripheral Reset ... Done
Enabling Memory Writes ... Done
Halting Processor ... <Processor did NOT enter Debug Mode!> ... Done
Clearing Watchdog ... Done
Loading CPU Configuration Code ... Skipped

Probing Flash at Address: 0x1FC00000 ...
Detected pFlash Chip ID (VenID:DevID = 0000 : 0000)
*** Found a (8MB) CFI Compatiable Flash Chip from Unknow

    - Flash Chip Window Start .... : 1C000000
    - Flash Chip Window Length ... : 00800000
    - Selected Area Start ........ : 1C000000
    - Selected Area Length ....... : 00040000

*** You Selected to Flash the CFE.BIN ***

=========================
Flashing Routine Started
=========================
Total Blocks to Erase: 11

Erasing block: 1 (addr = 1C000000)...