|
|
发表于 2013-10-5 17:51:05
|
显示全部楼层
本帖最后由 1550261790 于 2013-10-5 21:07 编辑
. V d9 Q9 r5 H5 r% [
, r7 j x, K2 ~5 m- B( X5 |电信版烽火HG110刷了，没有CPU ID为tan的选项，选0和1启动不了，选2345则连不上. O! y! }/ V" A+ |% l
+ o& X3 ~; u$ M$ z x
找到原因了，原来要先刷成D-Link DSL_2640NRU的CFE后，刷这个固件才能正常启动，不用改成tan这个CPU id也能启动。这个固件就是没有USB和SSID只能设置一个，实在有点遗憾。我从dlink官方ftp下载了最新的DSL_2640NRU_v1.0.24_cfe_fs_kernel，TTL下改了Voice Board Configuration的数值后才启动起来的。
1 |8 y( ~0 T* t: S3 Y# c( ^Board IP address : 192.168.1.1:ffffff00 - m. G1 L) h/ C7 ~
Host IP address : 192.168.1.100 - z' v% F( [5 V
Gateway IP address : 6 I' p& ?3 }* b0 Y2 U: Z
Run from flash/host (f/h) : f
- U5 ~% q8 Z$ y- o5 @0 |8 ]Default host run file name : vmlinux
/ x8 Z$ P5 B- ]9 l0 _Default host flash file name : bcm963xx_fs_kernel : W, x+ `) `, \; v0 \. w; J
Boot delay (0-9 seconds) : 1 6 r( N0 }# Q2 H# s
Boot image (0=latest, 1=previous) : 0
2 a8 r" W. g7 XBoard Id (0-6) : 96328avng
$ @; z0 g7 Q) z. D# cNumber of MAC Addresses (1-32) : 11
' v4 [- v9 F) g' Q# h! NBase MAC Address : 00:0a:c2:34:55:d8 9 _# \* C- n. ?" c& a6 H
PSI Size (1-64) KBytes : 48
, E8 {6 ?; T3 R) |5 O2 WEnable Backup PSI [0|1] : 1
6 b2 q+ [4 B' z: L: p' Q5 ^System Log Size (0-256) KBytes : 64 + Z% E, K: Z, z% ~ c' ?$ U5 y; j
Main Thread Number [0|1] : 0 - K7 |; h& q! w1 h: I, O1 e
Voice Board Configuration (0-11) : AVNG_VE890HV & b. P: c9 q6 \2 g
; S, F0 [4 s9 j4 T O话说刷openwrt-96328avng-16M-flash-generic-squashfs-cfe.bin，硬是没启动起来，也许是跟CFE有关，也许是固件的问题
+ @9 C7 s% A. c% vBooting from only image (0xb8010000) ...- X* X, ?8 C; u: g) i
Code Address: 0x80010000, Entry Address: 0x800100007 Y" F% w. t% i9 h+ b% M5 }
LZMA: Prossible old LZMA format, trying to decompress..2 N1 r" o9 Q; H5 ^2 y) I1 V. ~
Decompression OK!0 V9 h9 r9 Z* i% O# F
Entry at 0x80010000
% \* j3 M) @" _Closing network.8 v; g6 @9 U) O7 M w
Disabling Switch ports.
% c8 @# ?9 B1 ~3 |Flushing Receive Buffers...
2 N3 D" ?5 ^$ ^6 c0 k; g& o0 buffers found.
; o/ p0 ^- O9 q$ TClosing DMA Channels.7 D, T* @) N5 r' L: H
Starting program at 0x80010000
7 ~, Y) L* A7 D( i[ 0.000000] Linux version 3.10.13 (openwrt@huchra) (gcc version 4.6.4 (OpenWrt/Linaro GCC 4.6-2013.05 r38297) ) #1 Thu Oct 3 09:38:26 PDT 2013
* o+ }3 R' z0 W2 Y% G3 c[ 0.000000] Detected Broadcom 0x6328 CPU revision b0
1 O% j+ E8 `6 H; p# F: _% Z. c[ 0.000000] CPU frequency is 320 MHz
( d' S( M3 e) r, o' v[ 0.000000] 64MB of RAM installed0 e2 w/ ?$ q$ ?5 n# q
[ 0.000000] registering 32 GPIOs) Z' A) v# n7 u' M) h7 O
[ 0.000000] board_bcm963xx: Boot address 0xb8000000
R2 e# D N: @5 ^[ 0.000000] board_bcm963xx: CFE version: unknown
* f$ ~: j! S4 K2 k[ 0.000000] bcm63xx_nvram: nvram checksum failed, contents may be invalid (expected ffffffff, got d6d2390d)- c# ^8 ?5 a% Z2 a1 A
[ 0.000000] board_bcm963xx: unknown bcm963xx board: 63av [ 0.000000] bootconsole [early0] enabled" I7 D; V( t+ s) P/ {9 V* n! v1 Y2 m7 m
[ 0.000000] CPU revision is: 0002a075 (Broadcom BMIPS4350)6 r& G% [- p1 T4 f9 w* U4 q' U& O
[ 0.000000] Kernel panic - not syncing: unable to detect bcm963xx board3 \4 `2 N1 Y. N3 f |
|
|
楼主: zhjook
/1 
44152102000001
