本帖最后由 jadi 于 2011-11-9 00:31 编辑 5 t- m0 C) y- R7 C1 `- \
( H! d9 {6 N6 _5 c高手们来帮看看如何给TP406改NR285PB提高CPU频率 + [* p# y, i2 A; Q/ J
先看TTL启动信息
* X2 V! f. z6 u$ L/ `Booting...
# n7 Q. u% L. u3 q5 [9 C/ |! K2 f2 ^=============================9 x% B' b: w+ N- [
<Probe SPI #0 >
5 i* E/ h- ?$ Y. E/ ?1.Manufacture ID=0x000000c20 V1 m( w5 ]4 z, o
2.Device ID=0x00000020$ y1 X( x( _3 t9 D' M1 t5 B
3.Capacity ID=0x00000015
2 k/ y0 [ L* r, ^8 }3 Y4.MXIC SPI (2 MByte)!8 F2 }/ G1 V: e! I S- W2 D& A
5.Total sector-counts = 512(sector=4KB) d5 _" ^- g* B* `- s
6.spi_flash_info[0].device_size = 217 A" Y3 q/ x" g- Y
5 E+ x; q1 x, p0 K7 q) F/ J; \---RealTek(RTL8196C)at 2011.01.07-12:11+0800 version v1.0a [16bit](195MHz)# |6 Q4 n% V6 D7 ]3 n
uncompress_app 1
8 G$ X& I$ S; V- x3 F/ Funcompress_app 2
; H3 x, Q6 M4 ]1 y* Puncompress_app 36 o4 n% F9 g/ l) e$ g" n
uncompress_app 4
v" r3 N5 Y; u* I& muncompress_app 5
) u9 ]" q0 t# |! h% Z RJump to image start=0x80700000...
: g! S" q+ K$ O2 ojump to init, k" p/ J$ y6 c
gpio init+ g% a* N7 E1 z/ A/ r9 ]
watchdog enable
$ f$ [- u9 d% V+ A ]9 q% x' D5 e' PUUID check OK; p- N" N$ V$ g4 B ?1 x+ Y
checksum OK+ d! s$ O3 F. r' @* Z Z# U: z
init check OK0 ?5 A5 @) b& g0 W, s8 j
Loading Run Parameters...+ K* w( u% \) S
Parameters Are Blank!
' I0 V3 _! ~/ E+ z& w* ]Loading Default Parameters..." K+ S. [2 k# v# c5 J
para size 1KB# V& v9 u! F6 T
IGD-R1A2-V1.1.19CN-Netcore(NR285PB), IGD software for NR285PB, V1.1.19 Simplifie
* P8 X! I% S. e1 a- }6 y6 ^d Chinese version, 2011.01.07 12:15.<br>Copyright(c) by Netcore Technology Co.Lt
4 V" x) H! C# H* O' c' }d. All rights reserved.4 d; V% x4 ]4 C5 n- s0 G" L
LAN_IP=192.168.1.1,unusemem=1154KB6 i1 U5 H& A) X; ^ n
2 o. b9 D% M6 Y+ I% E' `
CPU频率被降低了一半
6 B2 `2 o& a, b5 @. `就这B
, n, l0 P( g& q& h, a |
粤公网安备44152102000001号 
发表于 2011-11-9 00:29:25