刚刚找了一个CON芯片的4.1.0.38固件，和原来的不大一样的界面，已上传到网络硬盘

whyh

好用吗?!

jiaoshi

木鸟兄你用佳能A70照的相怎么是糊的哟。

wzckq

默认网关192.168.1.1.用户密码admin passowrd.以下是界面.跟爱捷特的固件差不多.呵


system log:
01/01/1970 00:00:00> Ethernet Device 0 Detected
01/01/1970 00:00:00> ATM: Detected
01/01/1970 00:00:00> ATM: Setting up vcc0, VPI=8, VCI=35
01/01/1970 00:00:00> Initialized Dynamic NAPT.
01/01/1970 00:00:00> ZDev device loaded OK.
01/01/1970 00:00:00> CfgMgr: ';Console.dlz'; module loaded.
01/01/1970 00:00:00> CfgMgr: ';Shtm.dlz'; module loaded.
01/01/1970 00:00:00> CfgMgr: ';Washer.dlz'; module loaded.
01/01/1970 00:00:00> CfgMgr: ';Apimage.dlz'; module loaded.
01/01/1970 00:00:00> CfgMgr: ';Prism.dlz'; module not found.
01/01/1970 00:00:00> CfgMgr: ';Fwbsd.dlz'; module not found.
01/01/1970 00:00:00> CfgMgr: ';Console.dlz'; module activated.
01/01/1970 00:00:07> CfgMgr: ';Shtm.dlz'; module activated.
01/01/1970 00:00:07> CfgMgr: ';Washer.dlz'; module activated.
01/01/1970 00:00:07> CfgMgr: ';Apimage.dlz'; module activated.
01/01/1970 00:00:07> CfgMgr: ';PrismModuleEntry'; module entry not found.
01/01/1970 00:00:07> CfgMgr: ';FwbsdModuleEntry'; module entry not found.
01/01/1970 00:00:33> ATM Connected
01/01/1970 00:00:33> ATM layer is up, cell delineation achieved
01/01/1970 00:00:33> ADSL connected
01/01/1970 00:00:33> Modulation: G.dmt
01/01/1970 00:00:33> Annex Mode: ANNEX_A
01/01/1970 00:00:33> Max Tx Power: -38dBm/Hz
01/01/1970 00:00:33> CO Vendor: ALCATEL_NETWORK
01/01/1970 00:00:33> d/s SNR: 16.6dB, u/s SNR: 23.0dB
01/01/1970 00:00:33> d/s Attenuation: 31.1dB, u/s Attenuation: 18.0dB
01/01/1970 00:00:33> d/s Data Rate: 2144kbps, u/s Data Rate: 512kbps
01/01/1970 00:00:33> d/s Latency: FAST, u/s Latency: FAST
01/01/1970 00:00:33> d/s total bit capacity: 1534bits, used: 544bits
01/01/1970 00:00:33> u/s total bit capacity: 152bits, used: 152bits
01/01/1970 00:00:33> ATM Tx Error Count: 0, Rx Error Count: 0
01/01/1970 00:00:33> PPP1 PPPoE PADI Sent
01/01/1970 00:00:33> PPP1 PPPoE Session is established.
01/01/1970 00:00:39> PPP1 PAP Authentication success
01/01/1970 00:00:39> PPP1: PPP IP address is 220.190.121.195
01/01/1970 00:00:39> PPP1: PPP Gateway IP address is 220.186.242.225
01/01/1970 00:00:39> PPP1: DNS Primary IP address is 61.153.177.201
01/01/1970 00:00:39> PPP1: DNS Secondary IP address is 61.153.177.197
01/01/1970 00:00:39> NAT/NAPT Session Start: interface ppp1, WAN IP is 220.190.121.195
01/01/1970 00:00:39> No Static Session Information is defined.
01/01/1970 00:00:40> DNS: Add IP address 61.153.177.201 (Auto discovered)
01/01/1970 00:00:40> DNS: Add IP address 61.153.177.197 (Auto discovered)
01/01/1970 00:00:40> PPP1 Session is up.
01/01/1970 00:00:41> DDNS: Updates disabled.
08/22/2005 01:30:49> Received time from Time Server 129.6.15.29
这个升级版本.有些模块找不到文件,没有UPNP的选项.DDNS是members.dyndns.org.使用不了.界面上有个hide advanced settings
可以打开或关闭高级选项..但配置界面基本上是老面孔.
稳定性一时半会测不出来.
升级除了我上边的方法之外.可以通过WEB刷.但不建议WEB刷.很容易导致容量不够溢出.原因是WEB升级只覆盖同名文件,不删除原有的文件,如果你有USB可以修复,试试也没事,大不了刷回来.

flashcat

以前试过，感觉不如4.1.0.44

wzckq

这个固件不行.BT慢的不行，而且开BT没一会儿就打不开网页了.关了BT又可以了。连接能力很差。
建议大家不要刷。

木鸟

和AZTECH的一样，找不到UPNP设置项