在Script file后面的Browse里面选择正确的脚本，点击 run script，执行完后刷新
我也是这个modem，以前没有用过无线，现在才发现用不了无线路由，有线路由正常，系统信息：AP MACON/C 是不是无线模块坏了？？
产品信息
Model Number AR7WRD
HW Revision Gaw7.2Z39-4
Serial Number none
Ethernet MAC 00:74:04:E5:69:D7
DSL Default MAC 00:74:04:E5:69:D8
AP MAC0 N/A
软件版本
Gateway 3.7.1_ASB
ATM Driver 6.00.01.00
DSL HAL 6.00.01.00
DSL Datapump 6.01.04.00 Annex A
SAR HAL 01.07.2b
PDSP Firmware 0.54
Wireless Firmware N/A
Wireless APDK N/A
Boot Loader 1.4.0.4
wyliq 发表于 2011-6-12 12:29 static/image/common/back.gif
在Script file后面的Browse里面选择正确的脚本，点击 run script，执行完后刷新
请问正确的脚本是啥样子的？我就这一个路由器，从哪有下载的？谢谢
wyliq 发表于 2011-6-12 12:24 static/image/common/back.gif
已经提示你错误原因了，就是MTD0/MTD1的值没有在env里面设置，你的猫之前清过了？
我参照前几页的其它朋友的env用PCTOOLS设置了MTD0/MTD1,文件可以刷进去了，但是现在WLAN灯总是灭的，而且在网页配置中打开WLAN也没用，无线还是不能打开
文件是用ruc备份出来的，里面有几个地方我有疑问
WIFI chip: TNETW1130
我打开路由器，里面芯片我看到明明是TNETW1350A(10-6BA5NCW)，
当然，这里有可能是我手工设置环境时的问题，
HWA_0 00:74:04:E5:75:92
HWA_2 00:74:04:E5:75:93
HWA_3 00:74:04:E5:75:93
WLAN_HWADDR 00:74:04:E5:75:94
mac_ap00:74:04:E5:75:95
这几个是我根据路由主板上MAC和参考网友的瞎写的，我现在怀疑是不是写错了。
另外就是我之前刷RouteTech的routertech-ar7wrd-1350A-pspboot-firmware-4ports-20110502版本曾经变砖，
只是刚刚使用你教的方法把env填了，然后把Gaw7.2Z39-4BE009(NSP3.7.1)()(Chinese_AnnexA_Upgrade).sign.img改为RT的文件名才恢复的，请帮忙看看是否我哪里有操作失误才会变砖？谢谢！
另：变砖时用PCTool查看到的env只有以下几项，其它都是我手工加的
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00800000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT(psbl)
IPA 192.168.1.1
咦，用zip压缩ruc的备份文件还要审核才行啊？
Router Upgrade Check 1.4.1 13/06/2011 20:10:56
Router IP: 192.168.1.1
CLI is needed
Description: HomePlusPlus500S6307MPWII
Board type: AR7WRD
Product ID: AR7WRD
Bootloader: psbl
RAM 16.0 MB
Flash (ROM) 8.0 MB
ADAM2: No
No default env: No
Linux version: 2.4.17_mvl21-malta-mips_fp_le
Firmware build: 070110
Firmware version: 3.7.1_ASB
Firmware stamp: 20070110183348
CPU: MIPS 4KEc V4.8
DSP: 6.01.04.00
Annex: A
/proc/wlan: No
/usr/sbin/wlan: Yes
TIAP: No
TNETW: No
Wireless: Yes
WIFI chip: TNETW1130******这里比较奇怪，我拆开看了就是TNETW1350A******
WIFI chip conf: No
Ports: 4
Ports (according to router): N/A
Marvell (or Marvell like): Yes
NSP: 3.7.1_ASB
Manufacturers:
RNDIS:
HRNDIS:
WARNING
Cannot confirm the model number of the wireless chip.
The wireless access point (AP) may be disabled - ensure it is enabled and then run this program again.
Select an AR7WRD PSPBOOT 4 PORT firmware.
Latest: routertech-ar7wrd-pspboot-firmware-4ports-20110502.zip
Please read the instructions that come with the firmware files before you upgrade.
Note: a later version of the firmware may exist depending on the how up to date the RUC is.
The date-stamp may be superseded, but the rest of the filename should be the same.
According to your current MTD values, you should be able to upgrade using a single firmware image.
/etc /versions
VERSION=3.7.1_ASB
BUILD=070110
BOARD=AR7WRD
FSSTAMP=20070110183348
#
/proc/wlan
cd: can't cd to /proc/wlan
#
/usr/sbin/wlan
#
/proc/ticfg/env
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00800000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT(psbl)
IPA 192.168.1.1
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
mtd4 0x90020000,0x90800000
BOOTCFG m:f:"mtd1"
NVS_TFTP_LOAD 1
HWA_0 00:74:04:E5:75:92
HWA_2 00:74:04:E5:75:93
HWA_3 00:74:04:E5:75:93
TR69_CR_USERNAME plugfest
TR69_CR_PASSWORD plugfest
configed 13
mtd5 0x90042000,0x90800000
Route_Enabled 1
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
vlynq_polaritylow
MAC_PORT 0
mtd1 0x90020090,0x9009f000
mtd0 0x9009f000,0x90800000
autoload 0
WLAN_HWADDR 00:74:04:E5:75:94******我怀疑这里是不是手工改错了******
Max_MACs 0
mac_ap00:74:04:E5:75:95******我怀疑这里是不是手工改错了******
cron_enable 1
configid 6
#
/proc/sys/dev/adam2/environment
cat: /proc/sys/dev/adam2/environment: No such file or directory
#
/proc/version
Linux version 2.4.17_mvl21-malta-mips_fp_le (root@localhost.localdomain) (gcc version 2.95.3 20010315 (release/MontaVista)) #3 Wed Jan 10 18:32:13 CST 2007
#
/proc/cpuinfo
processor : 0
cpu model : MIPS 4KEc V4.8
BogoMIPS : 211.35
wait instruction : no
microsecond timers : yes
extra interrupt vector: yes
hardware watchpoint : yes
VCED exceptions : not available
VCEI exceptions : not available
#
/proc/avalanche/avsar_ver
ATM Driver version:
DSL HAL version:
DSP Datapump version: Annex A
SAR HAL version:
PDSP Firmware version:
Chipset ID:
#
/proc/interrupts
7: 14779 R4000 timer/counter
8: 0 unified secondary
15: 552 serial
23: 0 + SAR
27: 1616 + Cpmac Driver
29: 0 vlynq0
31: 3 + DSL
32: 1 + USB
#
/proc/modules
tiatm 129704 c0031060 96 2
avalanche_usb 65208 c0020060 96 0 (unused)
#
/proc/flashinfo
cat: /proc/flashinfo: No such file or directory
#
/etc/PORTS
cat: /etc/PORTS: No such file or directory
#
logic:status/nspver
3.7.1_ASB
logic:status/has_marvell
1
/etc /led.conf
#################################################################
# Configuration File for AR7WRD board
##################################################################
module = adsl # module = {adsl,usb,pppoe}
##################################################################
# Note: state 0 for adsl is dummy state and is present only for ##
# compatibility with the new LED driver ##
##################################################################
state = 0 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1# gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1# gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1# gpio number
mode = 4 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 200 # flash on duration in ms
param2= 200 # flash off duration in ms
state = 3 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1# gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 4 # 0=dummy, 1=idle, 2=training, 3=sync, 4=activity
gpio = LED1# gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 100 # blink/flash rate in ms
######################################################################
module = usb # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 12 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 100 # blink/flash rate in ms
######################################################################
module = pppoe # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = pppoe down, 1 = pppoe active
gpio = 13 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
######################################################################
module = wlan # module = {adsl,usb,pppoe,wlan}
state = 0 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 0 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 1 # 0 = link down, 1 = link up
gpio = 6 # gpio number
mode = 1 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
state = 2 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 100 # blink/flash rate in ms
state = 3 # 0 = link down, 1 = link up, 2 = pkt rcv, 3 = pkt xmit
gpio = 6 # gpio number
mode = 2 # 0 = off,1 = on,2 = blinkoff,3 = blinkon, 4 = Flash
param1= 100 # blink/flash rate in ms
######################################################################
******以下部分是变砖时的env，其它是我参考前几页网友手工用PCTOOL输的，请帮忙看看是否有误，谢谢******
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00800000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT (psbl)
IPA 192.168.1.1
summerbee 发表于 2011-6-12 22:18 static/image/common/back.gif
产品信息
Model Number AR7WRD
HW Revision Gaw7.2Z39-4
无线没正确驱动，参看前面的内容
yustas 发表于 2011-6-13 20:52 static/image/common/back.gif
******以下部分是变砖时的env，其它是我参考前几页网友手工用PCTOOL输的，请帮忙看看是否有误，谢谢******
...
你前面刷过别的版本吧，env里面怎么没有无线的内容？