回复 ndir511 的帖子
还可以用firmware_tool输入TNETW ID来生成你的猫适用的ENV，把生成的env的无线rom部分用setenv写入env就可以了
回复 ndir511 的帖子
登陆 modem 用system里面的system Diagnostics查看下System environment (/proc/ticfg/env)
字段里面WLAN_EEPROM8后面是什么内容，我估计应该是171F1711075901FC0502000036006D00A600E5000404441016004510F903185A
回复 wyliq 的帖子
可否详细一点，在firmware_tool如何利用TNETW ID来生成猫适用的ENV？
回复 wyliq 的帖子
WLAN_EEPROM8后面真的是：171F1711075901FC0502000036006D00A600E5000404441016004510F903185A
本帖最后由 ndir511 于 2011-4-30 20:41 编辑
回复 wyliq 的帖子
我当时就是贝尔金刷OP成砖了，后来把别人的ENV写进去，但网卡的ROM不对，应该是MAC地址不对吧。。。。
回复 wyliq 的帖子
BUILD_OPS 0x301
bootloaderVersion 1.4.0.4
ProductID AR7WRD
HWRevision Unknown
SerialNumber none
MEMSZ 0x01000000
FLASHSZ 0x00800000
MODETTY0 9600,n,8,1,hw
MODETTY1 9600,n,8,1,hw
CPUFREQ 211968000
MIPSFREQ 211968000
SYSFREQ 105984000
PROMPT (psbl)
mtd2 0x90000000,0x90010000
mtd3 0x90010000,0x90020000
HWA_RNDIS 00:E0:A6:66:41:E1
HWA_HRNDIs 00:E0:A6:66:41:E2
BOOTCFG m:f:"mtd1"
MEMsZ 0x01000000
FLAsHsZ 0x00800000
DsL_BIT_TMODE 1
DsL_UPG_DONE 1
vcc_encaps0 0.0
vcc_encaps1 0.0
vcc_encaps2 0.0
vcc_encaps3 0.0
vcc_encaps4 0.0
vcc_encaps5 0.0
vcc_encaps6 0.0
vcc_encaps7 0.0
WLAN_EEPROM0 021156041B06001200000601095612000000010D56A9000000026D543D971906
WLAN_EEPROM1 73000000013984000100000101854C1068900105850600100001298507000000
WLAN_EEPROM2 01C1850000300001C585000000000111850000FFFF0115850000F0FF01A58500
WLAN_EEPROM3 8000000109850000800201010C03000000012184000000800181851D00030001
WLAN_EEPROM4 55090100000001E5580200000001F1580800000001D5581000000001B1580400
WLAN_EEPROM5 0000000000000000000C00C300FE0008011401260144014D014F0165019F01AF
WLAN_EEPROM6 01B70101390000110004010101000501060002010201021E000A000205020411
WLAN_EEPROM7 2244030610203031324004095449204143583130300507544920546573740108
WLAN_EEPROM9 4000145A1600020E0801E9000A01BA026400BB0176095000EF000A01D1026400
WLAN_EEPROM10 A10176090107100000400000010000050400010100000000FFFFFFFFFDFDFDFD
WLAN_EEPROM11 FBF4F4F4F40E0409090909090909090909090909090909090909090909090909
WLAN_EEPROM12 090909090909090909090909090909090909090909090909090909090909090E
WLAN_EEPROM13 0100000000000000000000000000000302A318A3180700012000000000000000
WLAN_EEPROM14 00000000000000000000000000000000000000000000000000
HWA_0 00:74:04:E6:57:7F
HWA_2 00:74:04:E6:57:80
HWA_3 00:74:04:E6:57:80
WLAN_HWADDR 00:74:04:E6:57:81
WLAN_EEPROM8 171F1711075901FC0502000037006F00A800E4000404441011004510DF03185A
Max_MACs 0
Route_Enabled 1
vlynq_polaritylow
cron_enable 1
mtd4 0x90020000,0x90400000
mtd5 0x90042000,0x90800000
DSL_BIT_TMODE 1
DSL_UPG_DONE 1
IPA 192.168.1.1
mac_ap 00:74:04:E6:57:82
configid 1
configed 13
mtd1 0x90020090,0x900a1000
mtd0 0x900a1000,0x90400000
MAC_PORT 0
NVS_TFTP_LOAD 1
Booting...
Launching kernel LZMA decompressor.
Kernel decompressor was successful ... launching kernel.
LINUX started...
Config serial console: ttyS0,9600
Auto Detection OHIO chip
This SOC has MDIX cababilities on chip.
WLAN 1350 chip configured.
vlynq_polarity = low
Success in setting up the VLYNQ.
CPU revision is: 00018448
Primary instruction cache 16kb, linesize 16 bytes (4 ways)
Primary data cache 8kb, linesize 16 bytes (4 ways)
Number of TLB entries 16.
Linux version 2.4.17_mvl21-malta-mips_fp_le (developers at RouterTech dot Org) #
162 Mon Jan 3 01:50:03 GMT 2011
Determined physical RAM map:
memory: 14000000 @ 00000000 (reserved)
memory: 00020000 @ 14000000 (ROM data)
memory: 00fe0000 @ 14020000 (usable)
On node 0 totalpages: 4096
zone(0): 4096 pages.
zone(1): 0 pages.
zone(2): 0 pages.
Kernel command line:
calculating r4koff... 00102c00(1059840)
CPU frequency 211.97 MHz
Calibrating delay loop... 211.35 BogoMIPS
Freeing Adam2 reserved memory
Memory: 14108k/16384k available (1726k kernel code, 2276k reserved, 111k data, 6
4k init)
Dentry-cache hash table entries: 2048 (order: 2, 16384 bytes)
Inode-cache hash table entries: 1024 (order: 1, 8192 bytes)
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 1024 (order: 0, 4096 bytes)
Page-cache hash table entries: 4096 (order: 2, 16384 bytes)
Checking for 'wait' instruction...unavailable.
POSIX conformance testing by UNIFIX
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
TI Optimizations: Allocating TI-Cached Memory Pool.
Warning: Number of buffers is not configured.Setting default to 120
Using 120 Buffers for TI-Cached Memory Pool.
DEBUG: Using Hybrid Mode.
NSP Optimizations: Succesfully allocated TI-Cached Memory Pool.
Initializing RT netlink socket
DEBUG: Starting ksoftirqd with ALWAYS_SOFTIRQ:0x3 NON ALWAYS SOFTIRQ:0xfffffffc.
DEBUG: Starting ksoftirqd with priority:0 policy:0 nice:19.
Starting kswapd
Disabling the Out Of Memory Killer
devfs: v1.7 (20011216) Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x1
squashfs: version 3.1 (2006/08/19) Phillip Lougher, lzma support by McMCC
pty: 32 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with no serial options enabled
ttyS00 at 0xa8610e00 (irq = 15) is a 16550A
Installed misc driver vlynq0: it handles vlynq bridge0 with 1 hop(s).
block: 64 slots per queue, batch=16
Initializing the TI QoS NSP Framework.
DEBUG: Initializing the Network Queue Manager Algorithms.
DEBUG: Initialization of the Translation Unit.
DEBUG: Initializing the LOCAL High Priority Database Module.
DEBUG: Initialization of the LOCAL High Priority Database Module successful..
Succesfully Initialized the TI QoS NSP Framework.
loop: loaded (max 8 devices)
Error getting CPMAC Configuration params for instance:0
Environment Variable:MACCFG_A not set in bootloader
Setting Default configuration params for CPMAC instance:0
MAC CFG : Tx Interrupts off , threshold : 20
Default Asymmetric MTU for eth0 1500
TI CPMAC Linux DDA version 1.9 - CPMAC DDC version 0.3
Cpmac: Installed 1 instances.
Cpmac driver is allocating buffer memory at init time.
PPP generic driver version 2.4.1
avalanche flash device: 0x400000 at 0x10000000.
Amd/Fujitsu Extended Query Table v1.3 at 0x0040
AMD/Spansion chip; checking for errata; Original Chip_ID=0x007E
AMD/Spansion chip; finished checking for errata; Revised Chip_ID=0x1000
RouterTech: AMD/Spansion chip; good chip with no errata; Restored Chip_ID=0x007E
Flash type: AMD; Manufacturer=AMD.
Manufacturer_ID=0x0001; Chip_ID=0x007E; Chip_Size=0x800000; Erase_Regions=0x0002
The Chief's FLASH extensions (www.RouterTech.Org): code loaded.
number of CFI chips: 1
Avalanche: No single image format found. Using mtd env variables
Looking for mtd device :mtd0:
Avalanche: Adding a mtd0 image (0xa1000), with size (0x35f000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x000a1000-0x00400000 : "mtd0"
mtd: partition "mtd0" doesn't start on an erase block boundary -- force read-onl
y
Avalanche: linking partition mtd0: mtd0 -> ../../mtdblock/0
Looking for mtd device :mtd1:
Avalanche: Adding a mtd1 image (0x20090), with size (0x80f70).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020090-0x000a1000 : "mtd1"
mtd: partition "mtd1" doesn't start on an erase block boundary -- force read-onl
y
Avalanche: linking partition mtd1: mtd1 -> ../../mtdblock/1
Looking for mtd device :mtd2:
Avalanche: Adding a mtd2 image (0x0), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00000000-0x00010000 : "mtd2"
Avalanche: linking partition mtd2: mtd2 -> ../../mtdblock/2
Looking for mtd device :mtd3:
Avalanche: Adding a mtd3 image (0x10000), with size (0x10000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00010000-0x00020000 : "mtd3"
Avalanche: linking partition mtd3: mtd3 -> ../../mtdblock/3
Looking for mtd device :mtd4:
Avalanche: Adding a mtd4 image (0x20000), with size (0x3e0000).
Creating 1 MTD partitions on "Physically mapped flash:0":
0x00020000-0x00400000 : "mtd4"
Avalanche: linking partition mtd4: mtd4 -> ../../mtdblock/4
Looking for mtd device :mtd5:
Looking for mtd device :mtd6:
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 1024 bind 1024)
GRE over IPv4 tunneling driver
Default Asymmetric MTU for gre0 1476
Linux IP multicast router 0.06 plus PIM-SM
ip_conntrack version 2.0 (512 buckets, 4096 max) - 400 bytes per conntrack
ip_conntrack_pptp version 1.9 loaded
ip_nat_pptp version 1.5 loaded
ip_tables: (C) 2000-2002 Netfilter core team
netfilter PSD loaded - (c) astaro AG
ipt_account 0.1.6 : Piotr Gasid硂 <quaker@barbara.eu.org>, http://www.barbara.eu
.org/~quaker/ipt_account/
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
NET4: Ethernet Bridge 008 for NET4.0
Initializing the WAN Bridge.
VFS: Mounted root (squashfs filesystem) readonly.
Mounted devfs on /dev
Freeing unused kernel memory: 64k freed
Algorithmics/MIPS FPU Emulator v1.5
Mon Jan3 01:54:00 UTC 2011
ledcfg: reading Standard Configuration File /etc/led.conf
ledcfg: configured 19 states
registered device TI Avalanche SAR
Ohio250(7200/7100A2) detected
DSP binary filesize = 374282 bytes
tn7dsl_init : env var DSL_BIT_TMODE is set
ERROR DSL: Unable to register with LED module
Texas Instruments ATM driver: version:
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
ifconfig: SIOCGIFFLAGS: No such device
resolver: configuration tree:
Jan3 01:54:16 cfgmgr(sar):Could not get oam_ping_interval from boot loader e
nv
Jan3 01:54:16 cfgmgr(sar):Trying to retreive the value from Configuration
Jan3 01:54:16 cfgmgr(sar): oamPingInterval(20)(20)
Jan3 01:54:16 cfgmgr(ap): AP Acquiring Lock
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Jan3 01:54:16 cfgmgr(pppoa-109): Valid Configuration Tree
PVC dB
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
vpi = -1 vci = -1 in_use = 0
Doing BRCTL ...
addbr br0
Doing BRCTL ...
addbr br1
Doing BRCTL ...
adDefault Asymmetric MTU for br0 1500
dbr br2
Doing BRCTL ...
addbr br3
Please press Enter to activate this console. Jan3 01:54:17 cfgmgr(resolver): s
tat successfull for /etc/resolv.conf.
Jan3 01:54:17 cfgmgr(resolver): Resolver Polling Timer Started succesfully.
Jan3 01:54:17 cfgmgr(sntp): NTP Polling Timer for DHCP Started succesfully.
Jan3 01:54:17 cfgmgr(sar): DSL Polling Timer Started succesfully.
Jan3 01:54:17 cfgmgr(fdb): Firewall NAT service started
Jan3 01:54:17 cfgmgr(ap): AP REPORT LOCK ACQUIRED
Jan Default Asymmetric MTU for br1 1500
3 01:54:17 cfgmgr(ap): wlan_handle_load_event - Acquired Lock
Jan3 01:54:17 cfgmgr(ap): MAC address is : 00:74:04:e6:57:81
Default Asymmetric MTU for br2 1500
Default Asymmetric MTU for br3 1500
root: USB is disabled
Jan3 01:54:19 cfgmgr(ap): WPA Authenticator Started
Jan3 01:54:19 cfgmgr(lanbridge0): Bridge Created: br0
Bridge Multicasting for br0 is now Enabled.
Doing BRCTL ...
addif br0 eth0
Jan3 01:54:21 cfgmgr(lanbridge1): Bridge Created: br1
Bridge Multicasting for br1 is now Enabled.
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
Jan3 01:54:23 cfgmgr(lanbridge2): Bridge Created: br2
Bridge Multicasting for br2 is now Enabled.
Default Asymmetric MTU for wlan0 1500
Default Asymmetric MTU for wdsup0 1500
Default Asymmetric MTU for wdsdw0 1500
Default Asymmetric MTU for wdsdw1 1500
Default Asymmetric MTU for wdsdw2 1500
Default Asymmetric MTU for wdsdw3 1500
Jan3 01:54:24 cfgmgr(lanbridge3): Bridge Created: br3
Bridge Multicasting for br3 is now Enabled.
Doing BRCTL ...
stp br0 off
Jan3 01:54:26 cfgmgr(lanbridgbr0: port 1(eth0) entering forwarding state
e0): Bridge Intebr0: topology change detectedrface Added: eth, propagating0
Doing BRCTL ...
stp br1 off
Jan3 01:54:28 initTnetwAddr: MemAddr=0xa4000000, RegAddr=0xa4080000
cfgmgr(ap): EEPROM len 473
Jan3 01:54:28 cfgmgr(ap): ERROR: DIE ID Mismatch eeprom ID: fc015907 11171f17
TNETW ID: b80158d1 820d0a24
Jan3 01:54:28 cfgmgr(ap): ERROR: Validate EEPROM Imdda: starting cleanup:
age failed
Jandda: cleanup finish succesfully, good-bye.
3 01:54:28 cfgmgr(ap): Error: Failed to get a valid EEPROM Image. AP is DOWN
Jan3 01:54:28 cfgmgr(ap): NVS_TFTP_LOAD is enabled to download the correct EEP
ROM image during next boot.
Set TFTP Server Address using IPA_SVR env variable
Jan3 01:54:28 cfgmgr(ap): Setting bootloader env NVS_TFTP_LOAD to 1
Jan3 01:54:28 cfgmgr(ap): AP Releasing Lock
Doing BRCTL ...
stp br2 off
Doing BRCTL ...
stp br3 off
Jan3 01:54:28 root: USB is disabled
Jan3 01:54:28 cfgmgr(sar): DSL Carrier is down
Jan3 01:54:28 cfgmgr(pppoa-109): del_iptable_rules : ppp_name not intact
BusyBox v1.18.1 (2011-01-03 01:52:40 GMT) built-in shell (ash)
Enter 'help' for a list of built-in commands.
回复 ndir511 的帖子
是就容易了，在system里面的run command里面输入如下两条命令，应该就可以搞定
unsetenv WLAN_EEPROM8
setenv WLAN_EEPROM8 240A0D82D15801B80502000036006D00A600E5000404441016004510F903185A
注意命令之间只能是半角空格，直接复制要删除多余的空格
本帖最后由 wyliq 于 2011-5-1 01:04 编辑
是TNETW ID不同，导致ROM存放的地址不同，MAC地址是放在WLAN_EEPROM0的最后到WLAN_EEPROM1的开头的，不改也没关系，后面还有WLAN_HWADDR 00:74:04:E6:57:81来修改