120# hyhqyz
附两种内存电路图，针脚定义都一样的
如何查看本机RG100A－AA的固件版本？
换了一片64M内存，但没有成功，换上后电流只有330ma，猫起动不了，不知何故，猫上面原来的内存型号是：M13S2561616A，我换上了金士顿DDR400的颗粒，型号是：HY5DU12822CTP-D43，请高手指教！！！
换了一片64M内存，但没有成功，换上后电流只有330ma，猫起动不了，不知何故，猫上面原来的内存型号是：M13S2561616A，我换上了金士顿DDR400的颗粒，型号是：HY5DU12822CTP-D43，请高手指教！！！
QYZHYH 发表于 2009-2-1 10:18 https://www.chinadsl.net/images/common/back.gif
HY5DU12822CTP-D43是8bit的芯片，6358需要16bit的
换了一片64M内存，但没有成功，换上后电流只有330ma，猫起动不了，不知何故，猫上面原来的内存型号是：M13S2561616A，我换上了金士顿DDR400的颗粒，型号是：HY5DU12822CTP-D43，请高手指教！！！
QYZHYH 发表于 2009-2-1 18:18 https://www.chinadsl.net/images/common/back.gif
确实如此！！谢谢
124# lastkiss
高人呀
2650修改为64M内存成功。
原始版固件。
下边是启动信息。
CFE version 1.0.37-8.7 for BCM96358 (32bit,SP,BE)
Build Date: Tue Dec 18 12:29:06 CST 2007 (odin@BS5)(Revision: 50)
Copyright (C) 2000-2006 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP1
Total memory: 67108864 bytes (64MB)
Total memory used by CFE:0x80401000 - 0x805288B0 (1210544)
Initialized Data: 0x8041DB60 - 0x8041FF30 (9168)
BSS Area: 0x8041FF30 - 0x804268B0 (27008)
Local Heap: 0x804268B0 - 0x805268B0 (1048576)
Stack Area: 0x805268B0 - 0x805288B0 (8192)
Text (code) segment: 0x80401000 - 0x8041DB5C (117596)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.12
Gateway IP address :
Run from flash/host (f/h) : f
Default host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 1
Board Id (0-12) : CTNEW_DSL2650
Number of MAC Addresses (1-32) : 12
Base MAC Address : 00:1c:f0:c7:14:7e
PSI Size (1-64) KBytes : 48
Main Thread Number : 1
Wireless ssid : ChinaNet-KGnF
Wireless wpakey : pewkqhxs
Serial number : 001CF0-35200001CF0C7147E
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from previous image (0xbe5e0000) ...
Code Address: 0x80010000, Entry Address: 0x80295018
Decompression OK!
Entry at 0x80295018
Closing network.
Starting program at 0x80295018
Linux version 2.6.8.1 (joan@mochow) (gcc version 3.4.2) #1 Wed Aug 27 14:50:39 CST 2008
prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 03fa0000 @ 00000000 (usable)
On node 0 totalpages: 16288
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 12192 pages, LIFO batch:2
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 16kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 256 (order 8: 2048 bytes)
Using 150.000 MHz high precision timer.
Dentry cache hash table entries: 16384 (order: 4, 65536 bytes)
Inode-cache hash table entries: 8192 (order: 3, 32768 bytes)
Memory: 61612k/65152k available (2042k kernel code, 3472k reserved, 533k data, 80k init, 0k highmem)
Calibrating delay loop... 299.00 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
Total Flash size: 16384K with 128 sectors
File system address: 0xbe5e0100
Can't analyze prologue code at 8020d1a4
SCSI subsystem initialized
usbcore: registered new driver hub
NTFS driver 2.1.15 .
JFFS2 version 2.2. (C) 2001-2003 Red Hat, Inc.
Initializing Cryptographic API
PPP generic driver version 2.4.2
NET: Registered protocol family 24
Using noop io scheduler
bcm963xx_mtd driver v1.0
JFFS2 mapped flash: Found 1 x16 devices at 0x0 in 16-bit bank
Amd/Fujitsu Extended Query Table at 0x0040
JFFS2 mapped flash: CFI does not contain boot bank location. Assuming top.
number of CFI chips: 1
cfi_cmdset_0002: Disabling erase-suspend-program due to code brokenness.
Creating 1 MTD partitions on "JFFS2 mapped flash":
0x00000000-0x00420000 : "JFFS2 filesystem"
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0050300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0052400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
brcmboard: brcm_board_init entry
InitNvramInfo
SES: Button Interrupt 0x3 is enabled
SES: LED GPIO 0x800d is enabled
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
u32 classifier
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 4096 bind 8192)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 80k freed
init started:BusyBox v1.00 (2008.08.27-06:58+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2008.08.27-06:58+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.
Loading drivers and kernel modules...
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
fuse init (API version 7.8)
fuse distribution version: 2.7.3
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 27 2008 14:49:05
Config Internal PHY Through MDIO
BCM63xx_ENET: Auto-negotiation timed-out
BCM63xx_ENET: 10 MB Half-Duplex (assumed)
eth0: MAC Address: 00:1C:F0:C7:14:7F
Broadcom BCM6358A1 Ethernet Network Device v0.3 Aug 27 2008 14:49:05
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
eth1: MAC Address: 00:1C:F0:C7:14:7E
dgasp: kerSysRegisterDyingGaspHandler: eth1 registered
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1C:F0:C7:14:80
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.120.25.0.cpe1.3
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
eth1 Link UP.
flag->enableoutfl = 0
profileGetFromFlashok!
flag->enableoutfl = 0
############## inifilename /var/ftpd.conf.##################
enter enablePVCQueue function
leave enablePVCQueue function
try to load from usb drives
Not have usb drives
############## inifilename /var/ftpd.conf.##################
ioctl, p_name=resetd
BcmAdsl_Initialize=0xC00BB3E8, g_pFnNotifyCallback=0xC00D47A4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA3FFFFF8, 0xB8001 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA3FFD3D4
AnnexCParam=0x7FFF7EB8 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
atmapi: DoInitialize
ATM proc init !!!
atmapi: BpGetWanDataLedGpio( &usValue ) == BP_SUCCESS
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (509 buckets, 0 max) - 392 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
==> Bcm963xx Software Version: 3.10L.01beta.A2pB022g.d20h <==
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_81!
pvc2684ctl -a -v 0.8.81 &
use ether mac 00:1c:f0:c7:14:7e
pvc2684d: Interface "nas_0_8_81" created sucessfully
set vlan_id before
set vlan_id 65535 vlan_priority 65535
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
device nas_0_8_81 entered promiscuous mode
br0: port 3(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 3(nas_0_8_81) entering forwarding state
BcmRfc2684_init interface is not up nas_0_8_81_1!
pvc2684ctl -a -v 0.8.81-x 1 -f &
pvc2684d: Interface "nas_0_8_81" created sucessfully
pvc2684d: Communicating over ATM 0.8.81, encapsulation: LLC
use ether mac 00:1c:f0:c7:14:7e
device nas_0_8_81_1 entered promiscuous mode
br0: port 4(nas_0_8_81_1) entering learning state
br0: topology change detected, propagating
br0: port 4(nas_0_8_81_1) entering forwarding state
enter InitialTr69QoS function
QoSConfig.enable = 1
===TEY:DHCP: server_config.max_leases=254
Cannot open /var/staticdhcp.cfg file!
class_num = 5
queue_num = 4
QoSConfig.enable = 1
qosentry.appname = None id = 1
qosentry.appname = None id = 2
qosentry.appname = None id = 3
qosentry.appname = None id = 4
qosentry.appname = TR069 id = 5
gtwy =
device eth0 left promiscuous mode
br0: port 1(eth0) entering disabled state
device eth1 left promiscuous mode
br0: port 2(eth1) entering disabled state
device nas_0_8_81 left promiscuous mode
br0: port 3(nas_0_8_81) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) entering forwarding state
device eth1 entered promiscuous mode
br0: port 2(eth1) entering learning state
br0: topology change detected, propagating
br0: port 2(eth1) entering forwarding state
device nas_0_8_81 entered promiscuous mode
br0: port 3(nas_0_8_81) entering learning state
br0: topology change detected, propagating
br0: port 3(nas_0_8_81) entering forwarding state
killall: lld2d: no process killed
killall: wsccmd: no process killed
Setting SSID "ChinaNet-KGnF"
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
SIOCSIFHWADDR: No such device
wlctl: wl driver adapter not found
Setting country code using abbreviation: "CN"
wlctl: Not Found
wlctl: Not Found
wlctl: Not Found
wl0: current channel 1
==>clark:getCurrentChannel()..set current channel
device wl0 entered promiscuous mode
br0: port 5(wl0) entering learning state
br0: topology change detected, propagating
br0: port 5(wl0) entering forwarding state
binding raw socket (index= 8, fd=6) on br0 to TOPO_ETHERTYPE
lld2d: listening at address: 00:1c:f0:c7:14:7e
lld2d: Using syslog
lld2d: Daemonizing...
lld2d: listening on interface br0
WlMngr::startWsc: client-pbc mode
*********************************************
Wi-Fi Simple Config Application - Intel Corp.
Version: Build 1.0.5, November 19 2006
*********************************************
Initializing stack... OK
Now starting stack
get mac = 00 1C F0 C7 14 80
dequeue : out of locking
Sun Dec 14 14:15:11 UTC 2008
tr69c: start!
ioctl, p_name=diapd
*** diapwait system init 1 sec start
ioctl, p_name=thttpd
ioctl, p_name=portald
entering USBWGET_Init!
entering shm_init!
Open shm_msg1572
USBWGET_Init success!
entering USBWGET_main!
entering chkUSBmyFile!
USB_file eroor!
USBWGET_Init Finish!
USBWGET_TaskID=815!
ioctl, p_name=wlanbtn
ioctl, p_name=ctclogd
!!!the telnet state is 1BcmDb_InitTelnet:stop telnet service
BcmDb_InitTelnet:Begain telnet service!
andy debug open success
gpio_fasync
Pasync_queue->magic = 0x4601
dir = www
sysSetMonitorFd:0
start to blink status led
*** diapwait system init 1 sec end
Plugin pppoe loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
Plugin pppoe called.
br0: port 1(eth0) entering disabled state
dequeue : out of locking
******* MODE: AP with built-in Registrar and UPnP Proxy *******
dequeue : out of locking
WSC: Build-in Regstrar, wait for start command....
下边是内存信息：
# cat /proc/meminfo
MemTotal: 61760 kB
MemFree: 36168 kB
Buffers: 2564 kB
Cached: 13440 kB
SwapCached: 0 kB
Active: 6936 kB
Inactive: 11632 kB
HighTotal: 0 kB
HighFree: 0 kB
LowTotal: 61760 kB
LowFree: 36168 kB
SwapTotal: 0 kB
SwapFree: 0 kB
Dirty: 0 kB
Writeback: 0 kB
Mapped: 5920 kB
Slab: 3888 kB
Committed_AS: 11144 kB
PageTables: 480 kB
VmallocTotal:1048560 kB
VmallocUsed: 2452 kB
VmallocChunk:1045856 kB
# sysinfo
Number of processes: 43
2:15pmup 1 min,
load average: 1 min:0.46, 5 min:0.18, 15 min:0.06
total used free shared buffers
Mem: 61760 25568 36192 0 2564
Swap: 0 0 0
Total: 61760 25568 36192
#
有点很奇怪，我看我的2650总内存数和其它网友的不太一样。
不知道是为什么。
等下就把猫连接到网络上边去测试有没问题。
真正的专业人士出现了！
期待中！
不错 有时间研究一下
继续关注一下，寻找内存芯片当中。找到了就下手