我的挂了，连CFE界面都进不去了
yangchengsh 发表于 2010-6-17 15:50 https://www.chinadsl.net/images/common/back.gif
你是通过什么途径刷的？CFE版本是多少？建议用ttl通过f命令刷。
用TTL线刷成功。灯果然基本正常了。
CFE version 1.0.37-6.5 for BCM96358 (32bit,SP,BE)
Build Date: Sun Apr 26 00:57:24 CST 2009 (root@MOD6538)
Copyright (C) 2000-2005 Broadcom Corporation.
Boot Address 0xbe000000
Initializing Arena.
Initializing Devices.
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
CPU type 0x2A010: 399MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)
Total memory used by CFE:0x80401000 - 0x80528280 (1208960)
Initialized Data: 0x8041DB50 - 0x8041F980 (7728)
BSS Area: 0x8041F980 - 0x80426280 (26880)
Local Heap: 0x80426280 - 00526280`(1048576)
Stack Area: 0x80526280 - 0x80528280 (8192)
Text (code) segment: 0x80401000 - 0x8041DB4C (117580)
Boot area (physical): 0x00529000 - 0x00569000
Relocation Factor: I:00000000 - D:00000000
Board IP address : 192.168.1.1:ffffff00
Host IP address : 192.168.1.100
Gateway IP address :
Run from flash/host (f/h) : f
Def醬lt host run file name : vmlinux
Default host flash file name : bcm963xx_fs_kernel
Boot delay (0-9 seconds) : 1
Boot image (0=latest, 1=previous) : 0
Board Id Name ` : 96358VW2
Psi size in KB : 24
Number of MAC Addresses (1-32) : 12
Base MAC Address : 0p:1f:a3:b2:46:8f
Ethernet PHY Type : External Switch Using Reverse MII
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from latest image (0xbe020000) ...
Code Address: 0x80010000, Entry Address: 0x802c0018
Decompression OK!
Entry at 0x802c0018
Closing network.
Starting program at 0x802c0018
Linux version 2.6.8.1 (lijf@deb-vm) (gcc version 3.4.2) #68 Sun Jun 6 19:48:24 CST 2010
Parallel flash device: name AM29LV320MT, id 0x2201, size 16384KB
96358VW2 prom init
CPU revision is: 0002a010
Determined physical RAM map:
memory: 01fa0000 @ 00000000 (usable)
On node 0 totalpages: 8096
DMA zone: 4096 pages, LIFO batch:1
Normal zone: 4000 pages, LIFO batch:1
HighMem zone: 0 pages, LIFO batch:1
Built 1 zonelists
Kernel command line: root=31:0 ro noinitrd console=ttyS0,115200
brcm mips: enabling icache and dcache...
Primary instruction cache 32kB, physically tagged, 2-way, linesize 16 bytes.
Primary data cache 16kB 2-way, linesize 16 bytes.
PID hash table entries: 128 (order 7: 1024 bytes)
Using 200.000 MHz high precision timer.
Dentry cache hash table entries: 8192 (order: 3, 32768 bytes)
Inode-cache hash table entries: 4096 (order: 2, 16384 bytes)
Memory: 28996k/32384k available (2114k kernel code, 3344k reserved, 633k data, 84k init, 0k highmem)
Calibrating delay loop... 399.76 BogoMIPS
Mount-cache hash table entries: 512 (order: 0, 4096 bytes)
Checking for 'wait' instruction...unavailable.
NET: Registered protocol family 16
Total Flash size: 16384K with 128 sectors
File system address: 0xbe020100
Can't analyze prologue code at 8021f25c
SCSI subsystem initialized
usbcore: registered new driver hub
devfs: 2004-01-31 Richard Gooch (rgooch@atnf.csiro.au)
devfs: boot_options: 0x0
Initializing Cryptographic API
loop: loaded (max 8 devices)
PPP generic driver version 2.4.2
PPP Deflate Compression module registered
PPP BSD Compression module registered
MPPE/MPPC encryption/compression module registered
NET: Registered protocol family 24
Using deadline io scheduler
bcm963xx_mtd driver v1.0
PCI: Enabling device 0000:00:0a.0 (0000 -> 0002)
ehci_hcd 0000:00:0a.0: EHCI Host Controller
PCI: Setting latency timer of device 0000:00:0a.0 to 64
ehci_hcd 0000:00:0a.0: irq 18, pci mem c0000300
ehci_hcd 0000:00:0a.0: new USB bus registered, assigned bus number 1
PCI: cache line size of 32 is not supported by device 0000:00:0a.0
ehci_hcd 0000:00:0a.0: USB f.f enabled, EHCI 1.00, driver 2004-May-10
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 2 ports detected
ohci_hcd: 2004 Feb 02 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI)
ohci_hcd: block sizes: ed 64 td 64
PCI: Enabling device 0000:00:09.0 (0000 -> 0002)
ohci_hcd 0000:00:09.0: OHCI Host Controller
PCI: Setting latency timer of device 0000:00:09.0 to 64
ohci_hcd 0000:00:09.0: irq 13, pci mem c0002400
ohci_hcd 0000:00:09.0: new USB bus registered, assigned bus number 2
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
usbcore: registered new driver usblp
drivers/usb/class/usblp.c: v0.13: USB Printer Device Class driver
brcmboard: brcm_board_init entry
SES: Button Interrupt 0x1 is enabled
======= GPIO CONFIG_BCM96358 init ========
Serial: BCM63XX driver $Revision: 3.00 $
ttyS0 at MMIO 0xfffe0100 (irq = 10) is a BCM63XX
ttyS1 at MMIO 0xfffe0120 (irq = 11) is a BCM63XX
NET: Registered protocol family 2
IP: routing cache hash table of 512 buckets, 4Kbytes
TCP: Hash tables configured (established 2048 bind 4096)
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
NET: Registered protocol family 15
Ebtables v2.0 registered
NET: Registered protocol family 8
NET: Registered protocol family 20
802.1Q VLAN Support v1.8 Ben Greear <greearb@candelatech.com>
All bugs added by David S. Miller <davem@redhat.com>
VFS: Mounted root (squashfs filesystem) readonly.
Freeing unused kernel memory: 2100180k freed
init started:BusyBox v1.00 (2010.06.03-13:16+0000) multi-call binary
Algorithmics/MIPS FPU Emulator v1.5
BusyBox v1.00 (2010.06.05-07:52+0000) Built-in shell (ash)
Enter 'help' for a list of built-in commands.
-sh: can't access tty; job control turned off
Loading drivers and kernel modules...
fuse init (API version 7.5)
fuse distribution version: 2.5.3
fuse init: DCACHE_BUG enabled
atmapi: module license 'Proprietary' taints kernel.
adsl: adsl_init entry
blaadd: blaa_detect entry
Broadcom BCMPROCFS v1.0 initialized
Broadcom BCM6358A1 Ethernet Network Device v0.3 Feb 24 2009 16:12:15
Config Ethernet Switch Through MDIO Pseudo PHY Interface
dgasp: kerSysRegisterDyingGaspHandler: eth0 registered
eth0: MAC Address: 00:1F:A3:B2:46:8F
Broadcom BCM6358A1 USB Network Device v0.4 Feb 24 2009 16:12:16
usb0: MAC Address: 00 1F A3 B2 46 90
usb0: Host MAC Address: 00 1F A3 B2 46 91
PCI: Setting latency timer of device 0000:00:01.0 to 64
PCI: Enabling device 0000:00:01.0 (0004 -> 0006)
wl: srom not detected, using main memory mapped srom info (wombo board)
wl0: wlc_attach: use mac addr from the system pool by id: 0x776c0000
wl0: MAC Address: 00:1F:A3:B2:46:92
wl0: Broadcom BCM4318 802.11 Wireless Controller 4.100.27.0.cpe2.1
dgasp: kerSysRegisterDyingGaspHandler: wl0 registered
proc file create OK for wireless lan.
eth0 Link UP.
is not default cfg.
is not default cfg.
BcmAdsl_Initialize=0xC005B3C8, g_pFnNotifyCallback=0xC0074324
AnnexCParam=0x7FFF7E28 AnnexAParam=0x00000980 adsl2=0x00000000
pSdramPHY=0xA1FFFFF8, 0xE61E 0xDEADBEEF
AdslCoreHwReset: AdslOemDataAddr = 0xA1FFD3D4
AnnexCParam=0x7FFF7E28 AnnexAParam=0x00000980 adsl2=0x00000000
dgasp: kerSysRegisterDyingGaspHandler: dsl0 registered
ATM proc init !!!
ip_tables: (C) 2000-2002 Netfilter core team
ip_conntrack version 2.1 (253 buckets, 0 max) - 376 bytes per conntrack
ip_conntrack_pptp version 2.1 loaded
ip_nat_pptp version 2.0 loaded
ip_ct_h323: init success
ip_nat_h323: init success
ADSL G.994 training
ip_conntrack_rtsp v0.01 loading
ip_nat_rtsp v0.01 loading
==> Bcm963xx Software Version: RU_1.00 <==
device usb0 entered promiscuous mode
br0: port 1(usb0) entering learning state
br0: topology change detected, propagating
br0: port 1(usb0) entering forwarding state
device eth0 entered promiscuous mode
br0: port 2(eth0) entering learning state
br0: topology change detected, propagating
br0: port 2(eth0) entering forwarding state
adding to all upstream interfaces
ADSL G.992 started
Setting SSID "Luren"
SIOCGIFFLAGS: No such device
ADSL G.992 channel analysis
Setting country code using abbreviation: "CN"
wlctl: Not Found
channel 1 selected
wl0: current channel 1
device wl0 entered promiscuous mode
br0: port 3(wl0) entering learning state
br0: topology change detected, propagating
br0: port 3(wl0) entering forwarding state
ADSL G.992 message exchange
ADSL link up, fast, us=512, ds=2464
BcmRfc2684_init interface is not up nas_0_1_33!
pvc2684ctl -a -v 0.1.33 -f &
pvc2684d: Interface "nas_0_1_33" created sucessfully
pvc2684d: Communicating over ATM 0.1.33, encapsulation: LLC
device nas_0_1_33 entered promiscuous mode
br0: port 4(nas_0_1_33) entering learning state
br0: topology change detected, propagating
br0: port 4(nas_0_1_33) entering forwarding state
device usb0 left promiscuous mode
br0: port 1(usb0) entering disabled state
device eth0 left promiscuous mode
br0: port 2(eth0) entering disabled state
device wl0 left promiscuous mode
br0: port 3(wl0) entering disabled state
device eth0 entered promiscuous mode
br0: port 1(eth0) entering learning state
br0: topology change detected, propagating
br0: port 1(eth0) enterinforwarding state
device wl0 entered promiscuous mode
br0: port 2(wl0) entering learning state
br0: topology change detected, propagating
br0: port 2(wl0) entering forwarding state
sntp: host not found
ioctl, p_name=diapd
I am open &async_queue = 0xc00367a4<3>kill_fasync: bad magic number in fasync_struct!
wlButtonInit open success
gpio_fasync
Pasync_queue->magic = 0x4601
*** diapwait system init 1 sec start
##############status LED blink now##################
Plugin pppoe loaded.
RP-PPPoE plugin version 3.3 compiled against pppd 2.4.3
Plugin pppoe called.
Using interface ppp0_1_33_1
fd_ppp = ppp_0_1_33_1
Couldn't increase MRU to 1500
localIP address 10.96.68.97
remote IP address 10.144.116.145
*** diapwait system init 1 sec end
dft, wanIpAddress = , wanSubnetMask =
vpi = 1, vci = 33, conId = 1, portId = 0
nat = 1, firewall = 1
Starting link
PPP: PPP Start Connection
Connect: ppp_0_1_33_1 <--> nas_0_1_33
Couldn't increase MRU to 1500
Initializing USB Mass Storage driver...
usbcore: registered new driver usb-storage
USB Mass Storage support registered.
Remote message: Authentication success,Welcome!
PAP authentication succeeded
peer from calling number 00:E0:FC:AD:CC:DE authorized
Local IP address changed to 125.71.184.109
Remote IP address changed to 125.71.184.1
PPP: PPP Connection Up.
dnsprobe: Primary DNS server = 221.236.9.9
dnsprobe: Secondary DNS server = 8.8.8.8
adding to all upstream interfaces
tr69c: start with default interface ppp_0_1_33_1
adding to all upstream interfaces
adding to all upstream interfaces
adding to all upstream interfaces
usb 1-1: new high speed USB device using address 2
scsi0 : SCSI emulation for USB Mass Storage devices
Vendor: Visture Model: Luren Rev: 2.10
Type: Direct-Access ANSI SC覫 revision: 02
SCSI device sda: 7085048 512-byte hdwr sectors (3628 MB)
sda: assuming Write Enabled
sda: assuming drive cache: write through
/dev/scsi/host0/bus0/target0/lun0: p1
Attached scsi removable disk sda at scsi0, channel 0, id 0, lun 0
USB Mass Storage device found at 2
VFS: Can't find ext3 filesystem on dev sda1.
SQUASHFS error: Can't find a 観UASHFS superblock on sda1
FAT: Unrecognizemount option "utf8=1" or missing value
FAT: utf8 is not a recommended IO charset for FAT filesystems, filesystem will be case sensitive!
Intrusion -> IN=ppp_0_1_33_1 OUT= MAC= SRC=222.64.20.32 DST=125.71.184.109 LEN=40 TOS=0x00 PREC=0x00 TTL=112 ID=256 PRO設=訡P SPT=64607 DPT=1433 WINDOW=16384 RES=0x00 SYN URGp
usb 1-1: USB disconnect, address 2
Intrusion -> IN=ppp_0_1_33_1 OUT= MAC= SRC=61.191.61.28 DST=125.71.184.109 LEN=40 TOS=0x00 蠷E0x00 訲L=113 ID=256 P襉TTCP SPT=v000 DPT=1t33`WIN腛W=16384 RE0x00 SYN URGP=0
usb 1-1: new high speed USB device using address 3
usb 1-1: control timeout on ep0in
usb 1-1: device not accepting address 3, error -71
usb 1-1: new high speed USB device using address 4
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Hitachi Model: HTS542525K9SA00 Rev:
Type: Direct-Access ` ANSI S肧I rev閟ion: 02
SCSI device sdb: 488397168 512-byte hdwr sectors (250059 MB)
sdb: assuming drive 鉧chez write 鬶rough
/dev/scsi/host1/bus0/target0/lun0: p1
Attached scsi disk sdb at scsi1, channel 0, id 0, lun 0
USB Mass Storage device found at 4
VFS: Can't find ext3 filesystem on dev sdb1.
SQUASHFS error: Can't find a SQUASHFS 髐perblock on sdb1
FAT: Unrecognized mount option "utf8=1" or missing value
FAT: utf8 is not a re鉶mme頳eIO charset for FAT files鵶tems, filesyst錷 will be case sensitive!
FAT: bogus number of reserved se鉻ors
VFS: Can't find a valid`艫T filesystem on dev sdb1.
-p
-t vfat /dev/sdb1
t -f
-t vfat -o iocharset=utf8 /dev/sdb1
本帖最后由 维升速 于 2010-6-19 02:59 编辑
4G U盘（FAT32）及250G移动硬盘（NTFS）分别挂载成功。修改过的双USB都能正常识别
我有个风扇接在TTL 3.3V取电，所以偶尔TTL信息是乱码。
NTFS分区存在只读的问题。之前用的1.14支持NTFS固件可以读写。
rg100a正在逐步发挥最大的威力了
学习一下。。。。。。
楼主刚刚发部的脱机下载固件怎么给删掉了啊
支持中 。。。。。。