找回密码
 注册

QQ登录

只需一步,快速开始

查看: 32019|回复: 56

付费求HUAWEI新版光猫su密码破解

[复制链接]
发表于 2014-10-9 09:16:41 | 显示全部楼层 |阅读模式
本帖最后由 antitel 于 2016-6-27 13:18 编辑

[授友委托]
  在HUAWEI新出来的光猫,把以前网上出现的破解方法全部屏蔽了,而且最可恨的是他们屏蔽了shell应用,这样即使接上TTL数据线,也只能在一个功能极少的wap>环境下(这个就是用telnet成功登陆后的第一个环境)。如果想查看或修改超级密码,在WAP>下是没办法的,甚至连基本的查看目录文件结构之类的命令都没有,更不要说其它更复杂命令的了。
  但是,在WAP>下有个su命令,输入su后,会先出来一串随机码,然后再让用户输入验证码。据说,这个su的验证码是有一个计算公式或“密码生成器”的。
  现在朋友愿出钱来获取这个“su密码生成器”,联系方式可以站内PM或电邮至garashi@163.com

[执行su命令,每次的验证码都不一样]


[华为某个教程中提到的“su密码生成器”]


[WAP>下shell等命令不能用]


[HG8346M WAP>下所有可用的命令]
amp add policy-stats pon
amp add policy-stats port
amp add stats gemport
amp clear policy-stats pon
amp clear policy-stats port
amp clear stats gemport
amp debug lswtable all
amp del policy-stats pon
amp del policy-stats port
amp del stats gemport
amp display efc
amp display l2act
amp display l2mac
amp display sfc
amp display userflow
amp show
ampcmd show car all
ampcmd show car index
ampcmd show emac stat
ampcmd show flow all
ampcmd show flow index
ampcmd show log
ampcmd show queue all
ampcmd show queue index
ampcmd trace all
ampcmd trace cli
ampcmd trace dpoe
ampcmd trace drv
ampcmd trace emac
ampcmd trace emap
ampcmd trace eth
ampcmd trace gmac
ampcmd trace gmap
ampcmd trace onu
ampcmd trace optic
ampcmd trace qos
bbsp add policy-stats btv
bbsp clear policy-stats btv all
bbsp clear policy-stats wan
bbsp del policy-stats btv
Broadband debug
Broadband display
chipdebug
clear amp pq-stats
clear file
clear lastword
clear pon statistics
clear poncnt dnstatistic
clear poncnt gemport upstatistic
clear poncnt upstatistic
clear port statistics
collect debug info
component delete all
cpu debug off
cpu debug on
dbg
debug ctp all
debug ctp step
debug ddns
debug dsp down msg
debug dsp msg
debug dsp up msg
debug ffwd all
debug ffwd event
debug ffwd fwd
debug ffwd lsw
debug ffwd napt
debug ffwd timer
debug fw pktinfo num
debug ifm
debug qoscfg
debug rtp stack
debug sample mediastar
debug vbr-fw all
debug vbr-fw hook
debug vbr-fw vbr-id
debug vport all
debug vport step
display access mode
display acl chain all
display amp policy-stats pon
display amp policy-stats port
display amp pq-stats
display amp stats gemport
display apmChipStatus
display batteryStatus
display bbsp stats btv
display bbsp stats wan
display bmsxml crc
display boardItem
display ctp all
display ctp detail
display cwmp debug
display deviceInfo
display dhcp_em result
display dsp channel para
display dsp channel running status
display dsp channel status
display dsp chip stat
display dsp codec status
display dsp interrupt stat
display epon ont info
display ethoam ma info
display ethoam md info
display ethoam mep info
display ethoam mep perf
display ffwd all
display ffwd stat
display file
display filter rf
display flashlock status
display flow
display fw all
display fw statistic
display inner version
display jb grid status
display jb para
display l2ffwd table
display lanmac
display lastword
display log info
display mac all
display macaddress
display machineItem
display memory info
display msg-queue
display napt all
display oaml2shell ethvlan
display onu info
display optic
display optmode
display patch information
display pon statistics
display poncnt dnstatistic
display poncnt gemport upstatistic
display poncnt upstatistic
display portstatistics
display pppoe_em result
display productmac
display rf config
display route
display rtp stack channel stat
display rtp stack para
display rtp stack version
display rtp statck chip stat
display sn
display startup info
display swm bootstate
display swm state
display sysinfo
display syslog
display timeout
display timer
display usb devList
display vbridge info
display vbridge nni-binding
display vbridge port-binding
display vbridge statistic
display vbridge uni-binding
display vbridge uplink-binding
display version
display vport all
display vport detail
display wan layer all
display wanmac
display wifi pa type
display wifichip
display wlanmac
display zsp version
get battery alarm status
get ip conntrack
get iptables filter
get iptables mangle
get iptables nat
get iptables raw
get mac agingtime
get ont oamfrequency
get opm switch
get optic debug info
get optic par info
get optic txmode
get poncnt upgemport
get port config
get port isolate
get port vlan
get rogue status
get testself
get vlan auth
get wlan advance
get wlan associated
get wlan basic
get wlan enable
get wlan stats
get wlan wps
ifconfig
igmp clear statistics
igmp get debug switch
igmp get flow info
igmp get global cfg
igmp get iptv
igmp get multilmac
igmp get port multicast config
igmp get statistics
igmp set debug switch
ip -6 neigh
ip -6 route
ip -6 rule
ip neigh
ip route
ip rule
load pack
logout
make ssh hostkey
mgcp mg-config
mgcp mgc 1
mgcp mgc 2
mid get
mid set
napt cli
netstat -na
oamcmd clear log
oamcmd debug
oamcmd pdt show log
oamcmd show flow
oamcmd show log
omcicmd alarm ctrl show
omcicmd alarm show
omcicmd clear log
omcicmd clear msg stat
omcicmd debug
omcicmd error log
omcicmd mib att show
omcicmd mib copy show
omcicmd mib show
omcicmd mib stat show
omcicmd pdt show log
omcicmd pm show
omcicmd show flow
omcicmd show log
omcicmd show msg stat
omcicmd show olt type
omcicmd show qos
omcicmd show tcont table
ping
qoscfg get
quit
reset
restore manufactory
route get default
save data
save log
set cwmp debug
set ethportmirror
set port isolate
set ringchk
set timeout
set userpasswd
set voicedebug
set voicedsploop
set voicelinetest
set voiceportloop
set voicesignalingprint
su
traceroute
tunnel show all
vbridge statistic clear
voice remote diagnose server set
voice remote diagnose set
vport statistic clear
vspa debug
vspa display confrence info
vspa display dsp running info
vspa display dsp state
vspa display mg if state
vspa display mg info
vspa display mgcp config
vspa display online user info
vspa display port status
vspa display signal scene info
vspa display signal scene list
vspa display user call state
vspa display user status
vspa mgc switch
vspa reset
vspa shutdown mg
wap ll
wap ls
wap ps
wap top

本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册

×
发表于 2014-10-9 18:30:41 | 显示全部楼层
本帖最后由 xulsccn 于 2014-10-9 19:00 编辑

楼主。之前做了很多功课哦。

su命令和su -命令最大的本质区别就是:前者只是切换了root身份,但Shell环境仍然是普通用户的Shell;而后者连用户和Shell环境一起切换成root身份了。只有切换了Shell环境才不会出现PATH环境变量错误。su切换成root用户以后,pwd一下,发现工作目录仍然是普通用户的工作目录;而用su -命令切换以后,工作目录变成root的工作目录了。用echo $PATH命令看一下su和su -以后的环境变量有何不同。以此类推,要从当前用户切换到其它用户也一样,应该使用su -命令。如图:
发表于 2014-10-9 23:12:33 | 显示全部楼层
帮开HG8120C 8245C 端口

高价解决不能shell问题

升级所有中兴3.0光纤猫版本,包括最新生产没办法上传固件升级的
发表于 2014-10-10 15:48:15 | 显示全部楼层
tm5880891 发表于 2014-10-9 23:12
帮开HG8120C 8245C 端口

高价解决不能shell问题

可以发猫来我解决,
 楼主| 发表于 2014-10-11 07:44:25 | 显示全部楼层
tm5880891 发表于 2014-10-10 15:48
可以发猫来我解决,

是一台一台解决还是提供彻底解决方案?
发表于 2014-10-11 09:27:59 来自手机 | 显示全部楼层
是曾相识,哈哈。俺们也是一步步自己试过来的。不过最后发现上华为的当。
发表于 2014-10-11 09:28:49 来自手机 | 显示全部楼层
z68021015 发表于 2014-10-11 09:27
是曾相识,哈哈。俺们也是一步步自己试过来的。不过最后发现上华为的当。

看看我以前发的贴
发表于 2014-10-11 10:29:46 | 显示全部楼层
antitel 发表于 2014-10-11 07:44
是一台一台解决还是提供彻底解决方案?

不提供彻底方案,搞一台收一台的费用
 楼主| 发表于 2014-10-12 05:01:10 来自手机 | 显示全部楼层
tm5880891 发表于 2014-10-11 10:29
不提供彻底方案,搞一台收一台的费用

朋友还是需要su计算器,不希望一台一台弄。
发表于 2014-10-12 07:09:15 | 显示全部楼层
好东西共同分享
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|宽带技术网 |网站地图 粤公网安备44152102000001号

GMT+8, 2025-7-2 05:12 , Processed in 0.025429 second(s), 5 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表