找回密码
 立即注册

QQ登录

只需一步,快速开始

查看: 7080|回复: 12

大亚DB120-B1刷成砖 请高手赐教

[复制链接]
发表于 2011-1-21 19:11:35 | 显示全部楼层 |阅读模式
在WEB下刷bcm96358GW_1.3_96358VW2这个文件 刷后192.168.1.1不能登入 lan1--lan3灯和电源2个USB灯交替闪烁
请高手指点一下 谢谢了 qq3264734
发表于 2011-1-21 22:43:15 | 显示全部楼层
俺的也成转了,期望高手解答
发表于 2011-1-21 22:51:06 | 显示全部楼层
我按照教程用电信3.1版不带CFE的一次刷成功。https://www.chinadsl.net/thread-44482-1-1.html
 楼主| 发表于 2011-1-23 19:30:27 | 显示全部楼层
我刷成公版后 不会设置 又在网页刷电信原版 现在彻底变砖了 只有电源和上网灯亮  进超级终端 要填写很多信息后 能进cFE 就是刷不进去固件 高手救我啊
发表于 2011-1-23 19:41:13 | 显示全部楼层
试一下cfe还活着不?活着就好办
 楼主| 发表于 2011-1-23 20:23:15 | 显示全部楼层
本帖最后由 sanyuan410 于 2011-1-23 20:23 编辑

CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二  1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device id 227a is not supported.

*** Board is not initialized properly ***

Press:  <enter> to use current value
        '-' to go previous parameter
        '.' to clear the current value
        'x' to exit this command
96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
96358VW2_b20     ------- 9
Board Id (0-9)                    :  

现在启动猫连接超级终端就是这样的 要填写一串数字
 楼主| 发表于 2011-1-23 20:25:23 | 显示全部楼层
CFE version 1.0.37-10.3 for BCM96358 (32bit,SP,BE)
Build Date: 二  1月 29 07:41:15 CST 2008 (root@ZTJ)
Copyright (C) 2000-2006 Broadcom Corporation.

Boot Address 0xbe000000

Initializing Arena.
Initializing Devices.
Parallel flash device id 227a is not supported.

*** Board is not initialized properly ***

Press:  <enter> to use current value
        '-' to go previous parameter
        '.' to clear the current value
        'x' to exit this command
96358VW2         ------- 0
96358VW          ------- 1
96358GWVG        ------- 2
96358MV2G        ------- 3
96358M           ------- 4
96358B           ------- 5
96358BGWE_OEM1   ------- 6
96359PONG        ------- 7
96358SV          ------- 8
96358VW2_b20     ------- 9
Board Id (0-9)                    :  0
Number of MAC Addresses (1-32)    :  0  12
Base MAC Address                  :  00:00:00:00:00:00  
PSI Size (1-64) KBytes            :  24  
Flash Block Size (1-128) in KBytes:  0  

Invalid flash block size (1-128) Kbytes;  Try again!
Flash Block Size (1-128) in KBytes:  0  128
Auxillary File System Size Percent:  0  
Main Thread Number [0|1]          :  0  
Flash layout changed. Need to erase all flash except bootrom
Invalid command: "e"
Available commands:

Flash Layout: Boot[0,0x00000000] Kern[-1,0xbdffffff]
              AuxFS[-1,0x00000000] Misc[-1,0x00000000] PSI[-1,0x00000000]
Flash RootFS Partition Length: 1107296257
100 MB Full-Duplex (auto-neg)
CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz
CPU running TP0
Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x805285A0 (1209760)
Initialized Data:          0x8041DD30 - 0x8041FDC0 (8336)
BSS Area:                  0x8041FDC0 - 0x804265A0 (26592)
Local Heap:                0x804265A0 - 0x805265A0 (1048576)
Stack Area:                0x805265A0 - 0x805285A0 (8192)
Text (code) segment:       0x80401000 - 0x8041DD30 (118064)
Boot area (physical):      0x00529000 - 0x00569000
Relocation Factor:         I:00000000 - D:00000000

Use default boot line parameters: e=192.168.1.1:ffffff00 h=192.168.1.159 g= r=h f=308nfs6358 i=bcm963xx_fs_kernel d=1 p=0
Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.159  
Gateway IP address                :   
Run from flash/host (f/h)         : h  
Default host run file name        : 308nfs6358  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-9)                    :   
Number of MAC Addresses (1-32)    : 0  
Base MAC Address                  : 00:00:00:00:00:00  
PSI Size (1-64) KBytes            : 24  
Flash Block Size (1-128) in KBytes: 0  
Auxillary File System Size Percent: 0  
Main Thread Number [0|1]          : 0  

*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 1
web info: Waiting for connection on socket 0.
CFE>         


信息填完 CFE出来了 LAN4口也能进网页 可是固件就是刷不进去
尝试很多版本了 哪个都刷不进去
 楼主| 发表于 2011-1-23 20:33:12 | 显示全部楼层
现在只有连上超级终端填上信息 LAN4口才能亮 才能连接上电脑升级页面
yanf141 该用户已被删除
发表于 2011-1-23 20:39:12 | 显示全部楼层
提示: 作者被禁止或删除 内容自动屏蔽
 楼主| 发表于 2011-1-23 20:46:40 | 显示全部楼层
回复 yanf141 的帖子

就是用这个软件
*滑块验证:
您需要登录后才可以回帖 登录 | 立即注册

本版积分规则

关闭

站长推荐上一条 /1 下一条

Archiver|小黑屋|宽带技术网 |网站地图 粤公网安备44152102000001号

GMT+8, 2026-3-7 23:31 , Processed in 0.023814 second(s), 5 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表