联通定制GWH-01设备 RG100S-AA启动过程

MINE

CFE version 1.0.37-102.9 for BCM96338 (32bit,SP,BE)
Build Date: 2009骞?10鏈?17鏃?鏄熸湡鍏?10:32:29 CST (root@localhost.localdomain)
Copyright (C) 2000-2009 Broadcom Corporation.
Serial flash device: name NX25P32, id 0xef15, size 4096KB
100 MB Full-Duplex (auto-neg)
CPU type 0x29010: 240MHz
Total memory: 16777216 bytes (16MB)
Boot Address 0xbfc00000

Board IP address                  : 192.168.1.1:ffffff00  
Host IP address                   : 192.168.1.100  
Gateway IP address                :   
Run from flash/host (f/h)         : f  
Default host run file name        : vmlinux  
Default host flash file name      : bcm963xx_fs_kernel  
Boot delay (0-9 seconds)          : 1  
Board Id (0-10)                   : 96333AW2G  
Number of MAC Addresses (1-32)    : 11  
Base MAC Address                  : 00:1f:a3:98:cc:02  
PSI Size (1-64) KBytes            : 24  
send udp message finished.
Not response, auto boot ...
*** Press any key to stop auto run (1 seconds) ***
Auto run second count down: 0
Booting from only image (0xbfc10000) ...
Code Address: 0x80010000, Entry Address: 0x801cb000
Decompression OK!
Entry at 0x801cb000
Closing network.
Closing DMA Channels.
Starting program at 0x801cb000
init started:  BusyBox v1.00 (2009.12.04-12:20+0000) multi-call binary

BusyBox v1.00 (2009.12.04-12:20+0000) Built-in shell (msh)
Enter 'help' for a list of built-in commands.

Loading drivers and kernel modules...

===== Release Version RG100S_V1.1 (build timestamp 091209_1612) =====
wl_cnt= 1
insmod: cannot open module `/lib/modules/2.6.21.5/extra/pktflow.ko': No such file or directory
interface eth1 does not exist!
interface eth1 does not exist!
interface eth1 does not exist!
SIOCGIFFLAGS: No such device
SIOCSIFADDR: No such device
bridge br1 does not exist!
device eth0.2 is not a slave of br0
bridge br1 does not exist!
device eth0.3 is not a slave of br0
bridge br1 does not exist!
device eth0.4 is not a slave of br0
bridge br1 does not exist!
device eth0.5 is not a slave of br0
bridge br1 does not exist!
WLmngr Daemon is running
optarg=0 shmId=0
device wl0 is not a slave of br0
Illegal target name.
Chain (null) doesn't exist.
Could not get lock!
wlmngr_retrieve() failed!
xxxx
insmod: cannot open module `/lib/modules/2.6.21.5/extra/pktflow.ko': No such file or directory
device wl0 is not a slave of br1
device wl0 is not a slave of br0
interface wl0.1 does not exist!
interface wl0.2 does not exist!
interface wl0.3 does not exist!
Setting SSID "CU_2095"
Setting SSID "CU_Gst1"
Setting SSID "CU_Gst2"
Setting SSID "CU_Gst3"
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
wlctl: Unsupported
ifconfig: eth1: error fetching interface information: Device not found
device wl0 is not a slave of br1
device wl0 is not a slave of br0
device wl0.1 is not a slave of br0
device wl0.2 is not a slave of br0
device wl0.3 is not a slave of br0


TTL接口定义（J3)
1 Rx
2 Tx
3 Gnd
4 Vcc

MINE

CFE下升级固件URL:
http://192.168.1.1/bcmtw.html

iview0520

楼主，想问一下，这个猫到底性能如何？是不是缩水比较厉害哟？

MINE

这个猫想升级非定制的固件，有固件没啊？
135641 发表于 2010-3-23 19:51

目前还没有可刷的第三方固件，不过有人已经在修改原BCM6358系列固件以支持这款设备。