找回密码
 注册

QQ登录

只需一步,快速开始

查看: 2902|回复: 7

RG100A CFE无法启动,提示Could not create TCP socket

[复制链接]
发表于 2010-1-10 23:42:00 | 显示全部楼层 |阅读模式
本帖最后由 L.C 于 2010-1-10 23:47 编辑

** Flash image not found. **后提示web error -1: Could not create TCP socket
jtag重刷cfe也不行,请问是怎么回事呢?
 楼主| 发表于 2010-1-10 23:53:58 | 显示全部楼层
Boot Address 0xbe000000



Initializing Arena.

Initializing Devices.

Parallel flash device: name AM29LV320MT|S29GL128-A, id 0x2201, size 16384KB
Flash Layout: Boot[0,0xbe000000] Kern[1,0xbe020000]

              AuxFS[93,0xbeba0000] Misc[125,0xbefa0000] PSI[127,0xbefe0000]

Flash RootFS Partition Length: 12058624

error on Ethernet Switch setup

Failed initializing enet hardware

CPU type 0x2A010: 300MHz, Bus: 133MHz, Ref: 64MHz

CPU running TP0

Total memory: 33554432 bytes (32MB)

Total memory used by CFE:  0x80401000 - 0x80529860 (1214560)

Initialized Data:          0x8041E740 - 0x80421060 (10528)

** Flash image not found. **

Board IP address                  : 192.168.1.1:ffffff00

Host IP address                   : 192.168.1.100

Gateway IP address                :

Run from flash/host (f/h)         : f

Default host run file name        : vmlinux

Default host flash file name      : bcm963xx_fs_kernel

Boot delay (0-9 seconds)          : 1

Board Id (0-8)                    : 96358VW2

Number of MAC Addresses (1-32)    : 12

Base MAC Address                  : 00:1f:a3:10:8f:99

PSI Size (1-64) KBytes            : 24

Flash Block Size (1-128) in KBytes: 128

Auxillary File System Size Percent: 25

Main Thread Number [0|1]          : 0

Could not activate network interface 'eth0': CFE error -1

udp_socket error

No answer .auto boot ...


web error -1: Could not create TCP socket.



web error -1: Could not create TCP socket.


CFE>
web error -1: Could not create TCP socket.



web error -1: Could not create TCP socket.
发表于 2010-1-11 00:21:08 | 显示全部楼层
原理与制作
发表于 2010-1-11 02:16:19 | 显示全部楼层
我的RG100a-aa刷2650遇到过你这样的问题
大概的意思是FLash程序未找到
后来直接刷了USR9113解决问题了速度和无线信号杠杠的


本帖子中包含更多资源

您需要 登录 才可以下载或查看,没有账号?注册

×
 楼主| 发表于 2010-1-11 10:11:51 | 显示全部楼层
回复 4# oovwvoo


没有固件的话应该是直接进入cfe模式的吧?
为什么会报错呢?
发表于 2010-1-11 22:32:10 | 显示全部楼层
在CFE模式下先i后e n,重新设置参数看看
发表于 2010-1-12 11:59:51 | 显示全部楼层
学习中。。。还没用过无线呢。{{XPX1{{
发表于 2010-1-13 13:42:45 | 显示全部楼层
先刷2650 1.00,再刷1.14!!
*滑块验证:
您需要登录后才可以回帖 登录 | 注册

本版积分规则

Archiver|小黑屋|宽带技术网 |网站地图 粤公网安备44152102000001号

GMT+8, 2025-5-19 22:03 , Processed in 0.030341 second(s), 3 queries , Redis On.

Powered by Discuz! X3.5 Licensed

Copyright © 2001-2020, Tencent Cloud.

快速回复 返回顶部 返回列表